Stockton 7 & 8 Inset Convector Stove User Instructions MODELS: 7125/7126 For Use in Great Britain and Eire This product is suitable for use in the stated countries. To install the product in other countries it is essential to obtain translated instructions and in some cases the product may require modification. Contact Stovax to obtain further information. IMPORTANT Please read these instructions carefully before using the appliance. Keep them safe for future reference and when servicing the appliance.
FOR YOUR RECORDS To assist us in any Guarantee claim please complete the following information:- Stovax dealer appliance was purchased from Name: ..................................................................................................................................................................................... Address:...............................................................................................................................................................................
OPERATING INSTRUCTIONS Before use of this appliance please read these instructions fully AIR CONTROLS 1. GENERAL 1.1 Airwash Control 7125 This stove is designed for domestic heating and should only be used for this purpose, and in accordance with the manufacturers operating instructions. 7126 It should be installed by a competent installer, in accordance with the relevant local and national regulations. 1.2 1.
OPERATING INSTRUCTIONS 3.11 We would recommend that the stove is burnt at high output for at least 30 minutes each day when it is in use. This will help reduce the build-up of tars and creosotes within the appliance. 2. USING THE STOVE FOR THE FIRST TIME 2.1 2.2 When new, it is best to burn the fire at a low output for the first few days of use. This will allow the construction to settle and all fixing glues and paint to fully cure. 4.
OPERATING INSTRUCTIONS 4.11 We would recommend that the appliance is burnt at high output for at least 30 minutes each day when it is in use. This will help reduce the build up of tars and creosotes within the stove. WARNING: DO NOT USE THE DOOR AS A REST OR SUPPORT WHEN REFUELLING OR ADJUSTING THE AIR CONTROLS AS THIS COULD CAUSE PERMANENT DAMAGE TO THE APPLIANCE. 5.2 As heat can remain in the ash for a long period after use care must be taken when removing and carrying the full ashpan.
MAINTENANCE AND SERVICING 1. GENERAL CLEANING 1.1 We would recommend that your Stockton stove be cleaned fully on a regular basis, according to the level of use. Attention should be given to cleaning the baffle system, flueways and removing ash. Regular cleaning and preventative maintenance will help give many years of safe use. 2. CLEANING GLASS 2.1 2.2 2.4 Before re-lighting the appliance, dry the glass fully. 2.5 Do not use abrasive cleaner or cleaning pads.
MAINTENANCE AND SERVICING This is a list of the maintenance products you may need to use Task Glass Cleaning Preventing Build-up of Creosote in Flue Sealing Flue Pipe Joints Re-Painting Cleaning the Surface of Matt Black Stoves Product Name Stovax Code Number Stove glass cleaner 500ml-wipe on Stove glass cleaner-spray on 4111 4103 Protector (15 sachets) Protector (1kg tub) 7002 7025 Fire Cement-500g tub Fire Cement-600g cartridge 2020 2021 Thermolac Black (400ml aerosol) Thermolac Black (200ml br
MAINTENANCE AND SERVICING 5. FITTING AND REMOVING OF BAFFLE 5.1 To maintain efficient combustion the stove is fitted with a steel baffle in the top of the firebox. 5.7 The baffle system is designed to give safe and efficient operation of the stove. Replace any damaged baffles immediately. 5.8 Do not modify the baffle system. 6. FITTING AND REMOVAL OF FIREBRICKS 6.1 As part of the routine maintenance of the stove you may have to remove the firebricks from the stove.
MAINTENANCE AND SERVICING 7.4 Clean and re-paint, the rear door if required. Clean the screws with light oil or WD40®, this will aid future removal. 7.5 Fit a new sealing rope between the new glass and the door, and place the glass into position in the door. Place the glass fixing clips into position and re-fix with the clean fixing screws, tighten the screws evenly until the clips hold the glass. Do not over tighten the clips as this could break the glass. 7.
MAINTENANCE AND SERVICING 8.4 Stockton 8 (7126) only, Remove the old centre strip seal and old fixing glue from the left hand door and use a clean, dry cloth to remove all old dust and debris. 8.5 Squeeze a generous bead of fresh Stovax Thermic Seal Glue into the rope locating groove. Press the new Stovax rope into the locating groove, placing the joint in the middle of the lower edge of the door. 8.
Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF Tel: (01392) 474011 Fax: (01392) 219932 E-mail: info@stovax.com www.stovax.