OPERATION & PARTS MANUAL SideWinder MODEL SHS62A CUT-OFF SAW Revision #0 (06/02/06) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.
NOTE PAGE
SHS62A CUT-OFF SAW — TABLE OF CONTENTS STOW — SHS62A CUT-OFF SAW Proposition 65 Warning ............................................. 2 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation .................................... 8-11 Specifications (Saw/Engine) ................................... 12 Decal Placement ....................
SHS62A CUT-OFF SAW — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all orders are treated as “Standard Orders”, and will ✓ FedEx or UPS Second Day or Third D
SHS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. This Owner's Manual has been developed to provide complete NOTE instructions for the safe and efficient operation of the STOW MODEL SHS62A CUT-OFF SAW.
SHS62A CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, when the saw is not in use. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable. Guards and Covers In Place NEVER operate the saw without blade guards and covers in place.
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION WARNING - Read This Manual Failure to follow instructions in this manual may lead to Serious Injury or even Death. This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the Stow SHS62A Cut-off Saw. SAFETY ■ DO NOT operate or service this equipment before reading this entire manual.
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION General Safety ■ ALWAYS read, understand, and follow procedures in Operator's Manual before attempting to operate this equipment. ■ ALWAYS hold the saw with both hands when the engine is running. Use a firm grip with thumbs and fingers encircling the handles. ■ ALWAYS keep all parts of the body away from the cutting-off blades when the engine is running. ■ ALWAYS keep the handles dry, clean and free of oil or fuel.
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION ■ NEVER leave the machine unattended while running. Diamond Blade Safety ■ NEVER run the engine without the air filter. Severe engine damage could occur. ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ NEVER wear jewelry or loose fitting clothing that may snag on the controls or moving parts, this can cause a serious injury. ■ NEVER operate this saw without the blade guard, or other protective guards in place.
SHS62A CUT-OFF SAW — RULES FOR SAFE OPERATION EMERGENCIES ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor, and fire department. This information will be invaluable in the case of an emergency. SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — SPECIFICATIONS Table 1. SHS62A Cut-off Saw Specifications 50 x 33 x18 in. (1270 x 838 x 457 mm) Dimension (Shipping) LxWxH Weight 22.9 lbs. (10.4 kg) Blade Size 14 in. (356 mm) Maximum Cut Depth 5 in. (127 mm) Arbor Size 1 in. (20 mm) Cutting Arm Reversible Table 2. SHS62A Power Source Specifications Engine Type Two-Stroke, Single Cylinder, Air cooled Displacement 3.86 cu. in (63.3 cc.
SHS62A CUT-OFF SAW — DECAL PLACEMENT Machine Operation And Safety Decals The SHS62A CUT-OFF SAW is equipped with a number of operation and safety decals (Figure 1). Should any of these decals become unreadable, replacements can be obtained from your dealer. P/N DCL 230 P/N DCL 231 P/N DCL 232 A P/N TBD P/N DCL 161 Figure 1. Safety Decals SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — CONTROLS & COMPONENTS 1 2 3 4 7 6 5 12 11 10 9 8 Figure 2. SHS62A Cut-off Saw Components 1 Figures 2 and 3 shows the location of the basic controls or components for the Stow Model SHS62A Cut-off Saw. Listed below is a brief explanation of each control or component. 1. Air Filter – Prevents dirt and debris from entering the engine air intake. Check filter periodically and keep cleaned or replace when necessary. NEVER run engine with a dirty air filter. 2.
SHS62A CUT-OFF SAW — CONTROLS & COMPONENTS 14 13 15 16 22 21 20 19 18 17 Figure 3. SHS62A Cut-off Saw Components 2 13. Blade Guard – Covers saw blade. 14. Front Handle – When lifting or carrying of the saw is required, use this handle. 15. Throttle Lock Lever – Using your thumb, press this lever downward and squeeze the trigger lever to lock the throttle in place. Use this option only to aid starting. Squeeze the trigger lever again to unlock the throttle. 18.
SHS62A CUT-OFF SAW — BLADE INSTALLATION INSTRUCTIONS The Stow Side Winder Cut-Off Saw comes with a Tool Kit (Figure 4) that assists you with day to day operations. You will need these tools for the assembly of your saw. Item G is a versatile screwdriver/wrench that accommodates common bolt/screw and nut head sizes of your saw. Item H is the wrench necessary to accommodate various allen screws. Figure 4.
SHS62A CUT-OFF SAW — WATER KIT INSTALLATION INSTRUCTIONS Contents of Water Kit The contents of the Water Kit cannot be purchased seperately. See Water Kit Assembly in Parts Section of this manual for Water Kit part number. Hose Clamp G Socket Head Cap Screw w/ Washer H Quick Disconnect Fitting I Water Hose J Hex Key Tool K (Included with Tool Kit) Figure 9.
SHS62A CUT-OFF SAW — BLADES PREPARATION / PRE-INSPECTION 1. Read and fully understand this manual, the safety instructions in particular, and the engine manufacturer's manual supplied with the saw. 2. Select the correct blade for each application. If abrasive blades are used, MAKE CERTAIN they are designed for use on a concrete floor saw. They must be reinforced and have a hole for the driving pin. When wet cutting with an abrasive blade, MAKE CERTAIN the blade is intended for wet cutting.
SHS62A CUT-OFF SAW — INITIAL START-UP/OPERATION INITIAL START-UP CAUTION DO NOT attempt to operate the saw until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. CAUTION Figure 13. Fuel to Oil Mixture NEVER operate the saw in a confined area or enclosed area structure that does not provide ample free flow of air.
SHS62A CUT-OFF SAW — INITIAL START-UP/OPERATION 7. Grasp the starter grip and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. 8. If the engine has started, slowly return the choke lever to the "OPEN" position. If the engine has not started repeat steps 1 through 9. 9. Squeeze the throttle lever trigger to release it from the halfthrottle position. 10.
SHS62A CUT-OFF SAW — MAINTENANCE V-Belt Changing Procedure N Remove the 2 hex nuts Land hex screw and washer M to gain access to the V-belt on the clutch side. Remove V-belt cover T. Figure 14. Belt Guard Cover Removal Remove the 2 hex nuts J and hex screw and guard adjustment knob I to gain access to the V-belt on the spindle side. Remove the Cover Guard K. Figure 15.
SHS62A CUT-OFF SAW — MAINTENANCE V-Belt Changing Procedure (continued) Re-tension the V-belt by turning the belt tensioning cam O . The V-belt should remain in tension. Fully tighten the three nuts N that lock the V-belt into the proper tensioning position. Figure 18. Reversing the Cutting Arm Re-install the guard Kand V-belt Tcovers. Fully tighten the two cap screws J and reinstall the adjustment knob I. N Figure 19.
SHS62A CUT-OFF SAW — MAINTENANCE Reversing the Cutting Arm Procedure NOTE This assembly procedure permits the operator to reorient the cutting blade closer to a wall, column and/or object. The Stow Side Winder Cut-Off Saw comes with a Tool Kit (Figure 16) that assist you with day to day operations. You will need these tools for the maintenance of your saw. Item G is a versatile screwdriver/wrench that accommodates common bolt/screw and nut head sizes of your saw.
SHS62A CUT-OFF SAW — MAINTENANCE Reversing the Cutting Arm Procedure (continued) Reverse the cutting arm 180 degrees as shown in the Figure 23, and re-tension the V-belt by turning the belt tensioning cam O . The V-belt should remain in tension. Fully tighten the three nuts N that lock the V-belt into the proper tensioning position. Figure 23. Reversing the Cutting Arm Re-attach the cover guard Kwith the 2 cap screws J, and reconnect the guard adjustment knob Figure 24.
SHS62A CUT-OFF SAW — MAINTENANCE (AIR/FUEL FILTER) Air/Fuel Filter Maintenance Procedures Check the fuel filter G located inside the fuel tank periodically for dirt/debris build up. It is recommended to change the fuel filter every 50 tanks of fuel. This engine is a 2-stroke gasoline engine requiring a specific fuel to oil mixture of 50:1(2%). It is recommended to use an unleaded gasoline rated at 92 octane (premium) with an oil for use on 2-stroke engines only. See Figure 13. Figure 25.
SHS62A CUT-OFF SAW — TROUBLESHOOTING (BLADE) TABLE 3. BLADE TROUBLESHOOTING SYMPTOM Blade slows or stops cutting. Blade does not cut straight and/or true. Blade discoloring, crackling and/or wearing excessively. POSSIBLE PROBLEM SOLUTION Blade too hard for the material being cut? Consult Dealer or Multiquip for correct blade. Try cutting very soft material (sandstone, silica brick, cinder block) to "Redress" the blade.
SHS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE) TABLE 4. TROUBLESHOOTING (ENGINE) SYMPTOM Difficult to star t, "fuel is available, but no SPARK at spark plug". POSSIBLE CAUSE Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Shor t circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap. Ignition coil defective? Replace ignition coil.
SHS62A CUT-OFF SAW — TROUBLESHOOTING (ENGINE) TABLE 4. TROUBLESHOOTING (ENGINE, CONTINUED) SYMPTOM POSSIBLE CAUSE Air cleaner not clean? "Weak in power" compression is proper and does not misfire. Rotational speed fluctuates. Recoil starter malfunction. Clean or replace air cleaner. Rebuild carburetor. Defective spark plug? Clean or replace spark plug. Improper spark plug gap? Set to proper gap. Water in fuel system? Flush fuel system and replace with correct type fuel.
SHS62A CUT-OFF SAW — FILTER KITS For Side Winder HS Series Cut-Off Saws SHS62A DRY FILTER KITS HS62FK1A HS62FK5A HS62FK10A [ Includes 1 ea.] HS52020270R- Foam Filter HS018600125R- Paper Filter HS018600056AR - Inner Filter [ Includes 5 ea.] HS52020270R- Foam Filter HS018600125R - Paper Filter HS018600056AR - Inner Filter [ Includes 10 ea.
SHS62A CUT-OFF SAW — EXPLANATION OF PARTS SECTION REMARKS The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice. Stow does not guarantee the availability of the parts listed. Sample Parts List: NO.
SHS62A CUT-OFF SAW — SUGGESTED SPARE PARTS SUGGESTED SPARE PARTS SHS62A SIDEWINDER CUT-OFF SAW 1 to 3 Units Qty. P/N Description 1 ............ HS52022011A ....... STARTER ASSEMBLY 3 ............ HS098000079R .... ROPE, STARTER 1 ............ HS50140060 ......... HANDLE, ROPE 1 ............ HS098000060A ..... SPRING & CASE, STARTER 6 ............ HS3055118 ........... SPARK PLUG 1 ............ HS50012023AR .... CLUTCH ASSEMBLY 1 ............ HS52022005 ......... FUEL CAP, W/O-RING 3 ............
SHS62A CUT-OFF SAW — MUFFLER ASSY. MUFFLER ASSY. PAGE 32 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — MUFFLER ASSY. MUFFLER ASSY. NO. 1 * 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 10 * 11 PART NO. HS3801052 HS3033074 HS50010145 HS3801045 HS005100913B HS3833073 HS50010198 HS50010197 HS52010441 HS097000092A HS50010058A PART NAME QTY. REMARKS SCREW 3 WASHER 5 COVER, MUFFLER 1 SCREW 2 SCREW 2 WASHER 2 DEFLECTOR, MUFFLER 1 SCREEN 1 MUFFLER ASSEMBLY ............................. 1 ......... INCLUDES ITEMS W/ * SCREW 2 GASKET, MUFFLER 1 SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — RECOIL START ASSY. RECOIL START ASSY. PAGE 34 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — RECOIL START ASSY. RECOIL START ASSY. NO. 14 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 * 23 24 25 * 26 * 27 * PART NO. HS50140060 HS098000079R HS098000060A HS3960017 HS3960116 HS50140055 HS3918006 HS52010439B HS3908036 HS097000092A HS52022011A HS52010410 HS50140056 HS52010404 PART NAME QTY. REMARKS HANDLE, STARTER ROPE 1 ROPE, STARTER 1 SPRING AND CASE, STARTER 1 SCREW 4 SCREW 1 COVER 1 WASHER 1 PULLEY, STARTER 1 SCREW 1 SCREW 4 STARTER ASSEMBLY .............................. 1 .......
SHS62A CUT-OFF SAW — CRANKCASE ASSY. CRANKCASE ASSY. PAGE 36 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — CRANKCASE ASSY. CRANKCASE ASSY. NO. 3 11 12 16 18 19 * 20 21 22 23 24 26 28 30 31 37 * PART NO. HS52010312 HS52020014 HS52020040 HS50010047AR HS52020273 HS3034012 HS52020013 HS50010029 HS3833073 HS006100303 HS097000080BR HS3801015 HS005100987 HS097000057 HS52020037 HS3023008 PART NAME QTY. REMARKS PLATE 1 GROMMET 1 CAP 1 GASKET, CRANKCASE 1 CRANKCASE W/ BEARING ASSY ........................ 1 .........
SHS62A CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY. V-BELT COVER (CLUTCH SIDE) ASSY PAGE 38 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY. V-BELT COVER (CLUTCH SIDE) ASSY. NO. 25 31 34 40 41 42 43 44 PART NO. HS52020240 HS50010148R HS3833073 HS3806021A HS3801066 HS52020019 HS3916008R HS006000300 PART NAME V-BELT COVER, (CLUTCH SIDE) NUT WASHER SCREW SCREW GUARD, BELT INNER WASHER BUSHING QTY. 1 2 3 2 1 1 2 1 REMARKS SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — V-BELT COVER (PULLEY) /BLADE GUARD ASSY. V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY. BLADE FLANGE INNER (LIP) 10 2 8 1 34 5 14 BLADE FLANGE OUTER (FLAT) 6 22 7 20 14 46 12 13 14 23 34 4 28 36 12 24 27 11 37 35 15 21 9 6 38 39 16 47 45 17 18 26 32 33 CLUTCH PULLEY 34 19 29 30 PAGE 40 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — V-BELT COVER (PULLEY) /BLADE GUARD ASSY. V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY. NO. 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 32 33 34 35 36 37 38 39 45 46 47 PART NO.
SHS62A CUT-OFF SAW — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 42 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — FUEL TANK ASSY. FUEL TANK ASSY. NO. 4 5 6 8 9 15 * 16 19 28 29 30 PART NO. HS52010082 HS093000448 HS018500066 HS018500096 HS50010093 HS099900090 HS52022005 HS50010061R HS50010218 HS50010093 HS50140023 PART NAME QTY. REMARKS BREATHER 1 TUBE 1 FITTING 1 VALVE BODY 1 CLIP 1 0-RING 1 CAP, FUEL ............................................................. 1 ......... INCLUDES ITEM W/ * SHOCK ABSORBER 1 FILTER, FUEL 1 TUBE 1 GROMMET 1 SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY. LIFTING HANDLE AND ROLLER ASSY. PAGE 44 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — LIFTING HANDLE AND ROLLER ASSY. LIFTING HANDLE AND ROLLER ASSY. NO. 1 2 3 7 17 18 20 21 22 23 25 26 27 29 30 PART NO. HS52020023 HS018100317 HS3072015 HS3801020 HS52020026 HS3960087 HS52010214 HS3960045 HS018100171A HS52010098 HS38003035 HS52010066R HS52020077A HS3833076 HS3806035 PART NAME HANDLE SCREW WASHER SCREW GUARD, FUEL TANK SCREW MAIN ROLLER SUPPORT UPPER SPACER, ROLLER SUPPORT LOWER ROLLER SUPPORT, ROLLER LOWER SCREW SHOCK ABSORBER FUEL TANK ASSY. WASHER SCREW QTY.
SHS62A CUT-OFF SAW — THROTTLE LINKAGE ASSY. THROTTLE ASSY. PAGE 46 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — THROTTLE LINKAGE ASSY. THROTTLE ASSY NO. 10 11 12 13 14 38% 39 40# PART NO. HS52010092 HS52010077 HS097000028 HS097000024 HS3960040 HS52022048A PART NAME QTY. REMARKS THROTTLE TRIGGER LEVER ............................... 1 ......... INCLUDES ITEM W/ # THROTTLE LOCK LEVER 1 SPRING 1 COVER, HANDLE/TANK 1 SCREW 3 CAP, THROTTLE LINKAGE ................................... 1 ......... NOT SOLD SEPARATELY THROTTLE LINKAGE ............................................ 1 .........
SHS62A CUT-OFF SAW — FLYWHEEL COVER ASSY. FLYWHEEL COVER ASSY. PAGE 48 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — FLYWHEEL COVER ASSY. FLYWHEEL COVER ASSY. NO. 3 4 5 6 PART NO. HS005000361 HS3833080 HS004000142 HS500110019A PART NAME WASHER, FLAT WASHER, LOCK NUT FLANGE, STARTER QTY. 1 1 1 1 REMARKS SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — FLYWHEEL ASSY. FLYWHEEL ASSY. PAGE 50 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — FLYWHEEL ASSY. FLYWHEEL ASSY. NO. 1 2 * PART NO. HS52020247R HS52012027 PART NAME QTY. REMARKS FLYWHEEL ................................................ 1 ......... INCLUDES ITEM W/ * PAWL SET 1 SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — IGNITION COIL ASSY. IGNITION COIL ASSY. PAGE 52 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — IGNITION COIL ASSY. IGNITION COIL ASSY. NO. 7 * 8 * 9 10 11 12 13 15 16 17 18 19 PART NO. HS094600169 HS094600097A HS052010362 HS3916004 HS006000315 HS094000227 HS52020148R HS52010132 HS094500497 HS097000121A HS099900397 HS004000438 PART NAME QTY. REMARKS SPRING SPARK PLUG 1 CAP, SPARK PLUG 1 CABLE WIRE 1 WASHER 2 WASHER 2 SCREW 2 COIL, IGNITION ASSY. ............................. 1 .........
SHS62A CUT-OFF SAW — AIR FILTER ASSY. AIR FILTER ASSY. PAGE 54 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — AIR FILTER ASSY. AIR FILTER ASSY. NO. 1 2 3 3A 4 5 6 7 8 9 10 11 12 13 14 20 21 22 23 24 PART NO. HS52012024B HS330000010 HS018600125R HS099900778A HS018600056AR HS3802002A HS3049007 HS52010014B HS52020270R HS093000468A HS018600090A HS52020021 HS52010016 HS072700182 HS3833073 HS52022006 HS52010060 HS52010041 HS52020018 HS093000468A PART NAME QTY. REMARKS FLANGE, PRE- FILTER, CAP 1 O- RING, FLANGE PRE- FILTER 2 FILTER, AIR (STANDARD) 1 FILTER, AIR (WET CUTTING) .................. 1 ...
SHS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY. CARBURETOR MOUNTINGASSY. PAGE 56 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — CARBURETOR MOUNTING ASSY. CARBURETOR MOUNTING ASSY. NO. 6 11 12 13 14 15 16 17 18 19 20 21 22 23 PART NO. HS3833073 HS52020060 HS094000215A HS61052009B HS097000059A HS52020008B HS50010028 HS3960057 HS52020271 HS018100354 HS52020177 HS097000092A HS52020039 HS50020026 PART NAME WASHER SPRING TUBE SCREW SPRING, MANIFOLD MANIFOLD, OUTER FLANGE SCREW CARBURETOR ASSEMBLY FUEL LINE, CARBURETOR SCREW SCREW SUPPORT, CARBURETOR MANIFOLD, INNER QTY.
SHS62A CUT-OFF SAW — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 58 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1 * 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 * 12 * 13 * 14 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 23 24 * 25 * 26 * 27 * 28 * 29 * 30 PART NO.
SHS62A CUT-OFF SAW — CRANKSHAFT / PISTON ASSY. CRANKSHAFT AND PISTON ASSY. PAGE 60 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — CRANKSHAFT AND PISTON ASSY. CRANKSHAFT AND PISTON ASSY. NO. 1 2 3 4 5 # * 6 # * 7 # * 8 * 9 10 13 14 15 17 25 27 29+ 32 33$ 34 35 36 PART NO. HS3055118 HS005100906A HS3833076 HS50010215 HS50020004 HS50010031 HS007201198 HS50092013 HS50092028 HS50010046B HS3037014 HS50090001R HS094500028R HS094500004 HS007201313 HS50012023AR HS004900137B HS097000097 HS52010030 HS52010035 HS52010034 HS52010029R PART NAME QTY.
SHS62A CUT-OFF SAW — WATER KIT ASSY. WATER KIT ASSY. PAGE 62 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — WATER KIT ASSY. WATER KIT ASSY. NO. 1 2 * 3 * 4 * 5 * 6 * 7 * PART NO. HS52012062 HS52010121 HS52010207 NOTE PART NAME QTY. REMARKS WATER KIT ASSY. .......................................................1 .......... INCLUDES ITEMS W / * FITTING, QUICK DISCONNECT 1 PLASTIC TIE WRAPS .................................................. 8 .......... NOT SOLD SEPARATELY HOSE CLAMP .............................................................1 ..........
SHS62A CUT-OFF SAW — TOOLS TOOLS PAGE 64 — SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — TOOLS TOOLS NO. 1 2 PART NO. HS4191240 00325 PART NAME QTY. REMARKS TOOL KIT 1 SMOKELESS 2-STROKE OIL....... 1 ............. CAN ONLY BE PURCHASED AS A CASE (QTY 36) SHS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
SHS62A CUT-OFF SAW — RECOMMENDED DIAMOND BLADES Recommended Diamond Blades for Your Blade Type Asphalt Green Concrete Light Weight Block PDHS1A PDHS2 PDHS2A SW2 SW2G SW2 PDHS3 PDHS3 PDHS3A SDW SDW SWG SWG HSC HSC HSG HSG PVL PVL KBL KBL BBL GET Medium Stone PDHS1 SW2 PDHS3A Soft Stone SBLA PDHS2 SW2G Concrete (Brick) Pavers SBL PDHS1 PDHS2A Standard Red Brick GPSA SBL PDHS1A Cured Concrete GPS GPS SBLA Concrete Block Saw GES GES GPSA Side Winder BBL GET GPT GPT
Effective: July 15, 2003 TERMS AND CONDITIONS OF SALE — PARTS Terms and Conditions of Sale STOW Construction Equipment PAYMENT TERMS Terms of payment for unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice. Parts invoices have terms of net 10 days. Minimum parts billing is $15.00 net. Applicable discounts will be computed on merchandise value only. Late charges will be assessed at prevailing rates.
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 FAX: 800-672-7877 310-537-3700 FAX: 310-637-3284 SERVICE DEPARTMENT 800-478-1244 FAX: 310-537-4259 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 FAX: 310-631-5032 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 FAX: 310-537-1173 310-537-3700, EXT.