Digital Microscope STAD206W/BK Users Manual
LIST OF CONTENTS Safety and Maintenance.................................................................................................................................. 1 Basic Parameters ............................................................................................................................................. 1 What’s in the box............................................................................................................................................. 2 Assembly .........
Safety and Maintenance 1. Please read this manual before use the microscope. If you do not follow the instructions, it„s possible to cause the device damaged. 2. The assembly includes small parts, particularly the thumbscrews used to hold the main device in place. Do NOT allow unsupervised access by infants or toddlers. 3. The microscope is not intended for field use. It is not waterproof, and should not be exposed to extreme temperatures.
What’s in the box (P1, what’s in the box) (P2, Assembly1) (P3, Assembly2) 2
Assembly 1. Screw the optical bracket on to the base (see the left picture above, P2 ). 2. Once you have done so, if the bracket is not aligned over the base, unscrew the locking ring, adjust the bracket‟s direction, and then turn the locking ring clockwise until it is tight. (After doing this, it will still be possible to hold the base and turn the bracket if sufficient force is applied, but it will not spin freely. ) 3. Loosen the small thumbscrews on the optical bracket. 4.
(P5, remote buttons) *Frozen: Keep the image on the screen. It works at standby, record modes. *Zoom in&out: digital zooming up to 8 times. *Brightness up&down: exposure compensation from +2. 0 to -2. 0. *Line Settings: „十‟on the remote is for net line setting. *Sharpness up&down: there are three levels of sharpness: Soft/Normal/Strong. both used to switch the levels, but in different orders. *Contrast up&down: same principle as Sharpness.
*Black & White: refer to pictures in below: Normal Black & White (P6 connect ) Quick start Connect Firstly, connect the optical stack to the power supply via the switch cable. See the picture(P6) above.
display turns on. totally fine. ) (It may turn on automatically while connecting cables at the first time, and it‟s *Troubleshooting If the display freezes, locate the “reset ” hole on the back of the monitor. Use a narrow object such as an unfolded paperclip to depress the button located inside. This resets all settings to their factory values and restarts the display. It does not erase saved images or video.
To play a video, press the OK button to start play. Press the OK button again to pause. Press Mode button to stop playing the current video. Hit the Mode button again to exit playback mode. While reviewing a still image or video, the Menu button can be used to provide additional options. Press the Menu button and hold for a while till options show up.
(P8, setup menu) Date/Time Press “OK” into Date/time setting. Use “Up” and “Down” to select the correct number for year/month/day. Once you finish setting a number, press “OK” on the monitor to the next number. Or, you can use “Left” and “Right” on the remote to get to the one that you want. Press “MENU” button on the remote to exit date/time setting directly. If you don‟t have the remote, you have to go through all over these settings one by one and then press M button again to exit.
3. Why can't I get clear pictures? Make sure that the LED lights work properly. Adjust the light to illuminate the object, adjust the object distance by using the large knob on the stand, and then rotate the focus controller. If you still cannot obtain a clear image, gently wipe the lens with a clean, dry cotton cloth or paper towel to ensure that the lens is clean. 4.
Our warranty doesn‟t cover: 1 If users can not provide the purchase proof or the Warranty. 2 If users use it in an improper environment, such as incompatible power supply, high temperature environment etc. 3 If the fault caused by accident, oversight, misoperation or natural disasters etc. 4 If the fault caused by people who are not belong to authorized organizations of our company during repacking, repair, dismantle, Or if users repack, repair or dismantle the device not following our advice.