SOLID SURFACE RESIN BATHTUB SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE BATHTUB THIS BATHTUB SHOULD ONLY BE INSTALLED BY A CERTIFIED PLUMBER CAUTION! streamlinebath.com TWO PEOPLE ARE REQUIRED TO LIFT THE BATHTUB HAVE QUESTIONS? CONTACT US BELOW: support@streamlinebath.
PRIOR TO INSTALLING These products must be installed by a fully insured and licensed plumber only. Installation of any product by anyone other than fully insured and licensed plumber shall void limited warranty. We are not responsible for any local code compliance for this product. Building and plumbing codes may vary state-to-state. Streamline shall not be held liable for any and all incidental damages or flood caused due to use of this product.
INSTALLATION GUIDE IS APPLICABLE TO THE FOLLOWING BATHTUB MODELS K-80-70FSWHSS-FM K-81-70FSWHSS-FM K-82-59FSWHSS-FM K-88-70FSWHSS-FM K-89-70FSWHSS-FM K-92-70FSWHSS-FM K-93-70FSWHSS-FM K-95-70FSWHSS-FM K-96-63FSWHSS-FM K-85-67FSWHSS-FM K-87-67FSWHSS-FM K-97-67FSWHSS-FM K-98-70FSWHSS-FM K-822-67FSWHSS-FM K-892-59FSWHSS-FM K-0907-65FSWHSS-FM K-962-67FSWHSS-FM K-1006-67FSWHSS-FM K-1009-68FSWHSS-FM K-1169-59FSWHSS-FM K-1486-67FSWHSS-FM K-1580-67FSWHSS-FM K-1681-63FSWHSS-FM K-1686-63FSWHSS
DRAIN DIAGRAMS 1 No. 2 3 DESCRIPTION Qty. 1 Cover 1 2 Gasket 1 3 Core 1 4 Body 1 5 Gasket 1 6 Gasket 1 7 Cap 1 4 Flexible Hose Pre-Installed to Bathtub 5 6 Overall Tube Length: 36'' 7 Drain Diameter: 1.
BATHTUB INSTALLATION 1. Ensure that the floor at the installation site has sufficient floor support and is level. 2. Waterproofing the floor is highly recommended. 3. Determine the location of the drainpipe on the floor by taking measurements of the drain and waste location underneath the unit. Clean the drain hole area in preparation of setting the drain. The area should be dry & free from any debris. 4. Remove the bathtub from its box.
5. Gently place the bathtub in the upside-down position on a tarp or cardboard sheet in order to avoid contact with any rough surface. 6. Loosen the nuts & washers from the metal frame. Adjust the leveling feet to align with the bathtub’s bottom as well as the floor and then tighten the washer and nuts. 7. Ensure to mark all positions of leveling legs on the floor using a pencil. Move the bathtub into the desired location near the drainpipe.
8. Before proceeding with installation, push the pop up into a close position and fill the bathtub above the overflow [Note: some models may not have an overflow] to test for overflow and drain leakage. 9. Proceed to place the provided flexible drain hose into the floor drain. 10. Please note, the flexible hose is a basic way that we provide to connect to the end plumbing in a home.
12. Apply silicone along the bottom of the bathtub In order to create an airtight seal. Then apply a bead of tub & tile caulk around the edges of the base. 13. With the bathtub now in place, wipe off any excess silicone, tub & tile caulk where the bathtub meets the floor. 14. Allow for up to 24 hours for the adhesive material to set.
SINGLE HANDLE FREESTANDING TUB&SHOWER FAUCET H-100-TFMSHCH
RECOMMENDED TOOLS Screwdriver Channel Locks Goggles Hammer WARNING: Please keep the tool for future use! Adjustable Wrench Teflon tape Allen key ATTENTION: for easy installation, you will need: 1. To read all the installation instruction completely before beginning. 2. To read all the warning, attention and maitenance information.
FAUCET INSTALLATION 1. Drill one hole of 130mmx130mm max and drill 3 holes with 80mm diameter as shown. 80 mm 2. Align the base ① with the holes exactly as shown. 1 HOT WATER COLD WATER MAX 130mm 3. Insert the expansion anchors ① into the holes on the base ② with a hammer, tighten with adjustable wrench.
4. Tighten the shower holder① into faucet body④ with a screw② and Allen key③. 1 2 3 4 INSTALLATION LOCATION 5. Connect hot and cold supply lines and test by opening water lines. HOT WATER COLD WATER 6. If there are no leaks, remove the 3 screws (1) with the Allen key (2), then remove plate (3) and nuts (4) as shown.
7. Connect hot water flexible hose(1) and cold water flexible hose(1) to the base (2) correctly as shown. 1 8. 2 Insert 3 screws (1) into holes on the plate (2), Tighten with allen key (3). 3 1 2 9. Put down cover (1) and complete installation.
CHECKING AND TESTING 1. Remove the aerator ② with aerator wrench, take out the o-ring ① too.Turn the faucet handle all the way on, turn on hot and cold water supply and flush water lines for one minute.Reinstall aerator with aerator wrench. 1 2 2. Check all connections at arrows for leaks, re-tighten it if necessary.
MAINTENANCE A. If there is splash or low flow rate,please remove the aerator with the wrench and clean the debris. B. If faucet leaks from the handle or drips from spout, please replace cartridge following the following steps: Disassemble the screw② with allenkey①, take out the handle③, then remove the trim cap④. 1. 1 2 4 3 2. Unscrew the cartridge nut① with adjustable wrench, then take out the old cartridge②. 1 2 3.
CLEANING AND CARE Daily cleaning and care are required in order to keep the product shining and properly working. 1. Clean it with water and dry it with soft cloth. 2. Clean the product with gentle liquid or glass cleaner. 3. Don't use acid cleaner. 4. Don't clean with abrasive material, abrasive paper or knife.
