FREESTANDING BATHTUB SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE BATHTUB THIS BATHTUB SHOULD ONLY BE INSTALLED BY A CERTIFIED PLUMBER CAUTION! TWO PEOPLE ARE REQUIRED TO LIFT THE BATHTUB QUESTIONS ON PRODUCT, INSTALLATION, RETURNS? PLEASE CONTACT streamlinebath.com support@streamlinebath.
WARRANTY RETURNS We thank you for your purchase. Here at Streamline®, our goal is to provide customers with exceptional bathroom and kitchen products. We understand that things sometimes don’t work out. If you are unsatisfied with your Streamline® product and would like to initiate a return, please reach out to support@streamlinebath.com .
PRIOR TO INSTALLING These products must be installed by a fully insured and licensed plumber only. Installation of any product by anyone other than fully insured and licensed plumber shall void limited warranty. We are not responsible for any local code compliance for this product. Building and plumbing codes may vary state-to-state. Streamline shall not be held liable for any and all incidental damages or flood caused due to use of this product.
DRAIN MODEL COMPATIBILITY FREESTANDING BATHTUB Model A1040-F+ (A604) N-140-60FSWH-FM N-160-60FSWH-FM N-260-66FSWH-FM N-261-62X30FSWH-FM N-262-58FSWH-FM N-263-62X31FSWH-FM N-300-59FSWH-FM N-301-69FSWH-FM N-320-60FSWH-FM N-321-70FSWH-FM N-360-62FSWH-FM N-380-63FSWH-FM N-381-67FSWH-FM N-420-63FSWH-FM N-421-67FSWH-FM N-422-70FSWH-FM N-540-62FSWH-FM N-541-67FSWH-FM N-542-70FSWH-FM N-560-59FSWH-FM N-561-67FSWH-FM N-562-71FSWH-FM N-580-62FSWH-FM N-581-66FSWH-FM N-620-63FSWH-FM N-660-59FSWH-FM N-661-6
Flexible Hose DRAIN DIAGRAMS Pre-Installed to Bathtub Model: A1040-C Overall Tube Length: 47'' Drain Diameter: 1.5'' Model: A1040-C No. Model: A1040-F+(A604) Model: A1840-0 ITEM Qty.
BATHTUB INSTALLATION 1. Ensure that the floor at the installation site has sufficient floor support and is level. 2. Waterproofing the floor is highly recommended. 3. Determine the location of the drainpipe on the floor by taking measurements of the drain and waste location underneath the unit. Clean the drain hole area in preparation of setting the drain. The area should be dry & free from any debris. 4. Remove the bathtub from its box.
5. Gently place the bathtub in the upside-down position on a tarp or cardboard sheet in order to avoid contact with any rough surface. 6. Loosen the nuts & washers from the metal frame. Adjust the leveling feet to align with the bathtub’s bottom as well as the floor and then tighten the washer and nuts. 7. Ensure to mark all positions of leveling legs on the floor using a pencil. Move the bathtub into the desired location near the drainpipe.
. Before proceeding with installation, push the pop up into a close position and fill the bathtub above the overflow [Note: some models may not have an overflow] to test for overflow and drain leakage. 9. Proceed to place the provided flexible drain hose into the floor drain. 10. Please note, the flexible hose is a basic way that we provide to connect to the end plumbing in a home.
12. Apply silicone along the bottom of the bathtub In order to create an airtight seal. Then apply a bead of tub & tile caulk around the edges of the base. 13. With the bathtub now in place, wipe off any excess silicone, tub & tile caulk where the bathtub meets the floor. 14. Allow for up to 24 hours for the adhesive material to set.
INTERNAL DRAIN INSTALLATION DIAGRAM Please Note: The drain may have already been installed by the manufacturer prior to shipment. These drawings are to only show how the drain connects to the bathtub.