Owner’s Manual & Installation Guide Freestanding Bathtub Please read all instructions carefully before proceeding with installation. Due to the complexity of the installation procedure a professional plumber is required. Specifications and directions may change without notice.
Table of Contents: 1. Installation Guide Applicable Bathtub Models..…..…… 1 2. External Drain Configuration...………………….…….… 3 3. External Drain and Overflow Installation………………. 4 4. Internal Drain Configuration…………………..……….... 5 5. Internal Drain and Overflow Installation…………..…… 6 6. Bathtub Installation………………………………..….….. 7 7. Product Care and Maintenance …………….……….….
Drain Model A-DWF-GLD and A-DWF-CH are used with below models.
Drain Model A1866 are used with below models.
3
1. Connect Drain Strainer & Drain Ell. Use silicone sealant. DO NOT use plumbers putty to seal. 2. Insert tailpiece into trap inlet. The tail piece may need to be cut for proper fit, 1" - 2" of the tailpiece should fit inside the trap. Slip the flange over the tail piece and slide down to floor. 3. Assemble tee section to tailpiece, overflow ell and drain ell using coupling nuts and O-rings that are provided . 4. Attach the tapered rubber gasket to the overflow ell.
Please note, the drain has already been pre-installed on the tub.
Note: 1. The drain might have already been installed by the manufacturer before shipment. 2. This drawing is showing how the drain connects to the bathtub only.
1. Move the bathtub into a flat location. 2. Put the drain hose into the floor drain. 3. Apply silicone along the bottom of the bathtub to create an airtight seal.
1. In order to clean the bathtub, please only use soft towel or soft sponge. Never use an abrasive materials such as a brushes to clean the tub. 2. Rinse or soak the tub for 10 minutes in warm water not exceeding 40 degrees Celsius, then wipe the surface with a soft towel to dry. Try to keep the surface dry after every use. 3. If deep cleaning is necessary, rinse or soak the tub in warm water for 30 minutes and add a bit of liquid soap or dish soap to the water. Rinse and dry with a soft towel.
Step 1 Step 2 Faucet installation 2 1 Checking and testing 1 3 2 1 1 2 Hot water 1 Cold water 2 80MM Drill one hole of 130mmX130mm max and drill 3 holes with 80mm diameter as shown. 4 1 2 3 Align the base① with the holes exactly as shown. 5 Insert the expansion anchors① into the holes on the base② with a hammer,tighten with adjustable wrench. Remove the aerator ② with aerator wrench, take out the o-ring ① too.
Step Step 4 4 Cleaning Cleaning and and care care H-100-TFMSHCH Daily cleaning and care are required in order to keep the product shining and properly working. 1 Clean it with water and dry it with soft cloth. RECOMMENDED TOOLS 2 Clean the product with gentle liquid or glass cleaner. 3 Don't use acid cleaner. 4 Don't clean with abrasive material, abrasive paper or knife.
Step 1 Step 2 Faucet installation 2 1 3 Checking and testing 1 2 Remove aerator by coin and open the hot and cold water supplies. Check for leaks. Turn on faucet handle for one minute to flush debris from faucet. Check all connections at arrows for leaks, re-tighten it if necessary. 1 Hot water 1 Cold water 2 80MM Drill one hole of 130mmX130mm max and drill 3 holes with 80mm diameter as shown. Align the base① with the holes exactly as shown.
Step 4 Cleaning and care H-120-TFMSHCH Daily cleaning and care are required in order to keep the product shining and properly working. 1 Clean it with water and dry it with soft cloth. RECOMMENDED TOOLS 2 Clean the product with gentle liquid or glass cleaner. 3 Don't use acid cleaner. 4 Don't clean with abrasive material, abrasive paper or knife.
Step 1 Step 2 Faucet installation 2 1 3 Checking and testing 1 2 1 1 2 Hot water 1 Cold water 2 80MM Drill one hole of 130mmX130mm max and drill 3 holes with 80mm diameter as shown. 4 1 2 3 Align the base① with the holes exactly as shown. 5 Insert the expansion anchors① into the holes on the base② with a hammer,tighten with adjustable wrench. Remove the aerator ② with aerator wrench , take out the o-ring ① too.
Step 4 Cleaning and care H-140-TFMSHCH Daily cleaning and care are required in order to keep the product shining and properly working. 1 Clean it with water and dry it with soft cloth. RECOMMENDED TOOLS 2 Clean the product with gentle liquid or glass cleaner. 3 Don't use acid cleaner. 4 Don't clean with abrasive material, abrasive paper or knife.
