FREESTANDING BATHTUB SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE BATHTUB THIS BATHTUB SHOULD ONLY BE INSTALLED BY A CERTIFIED PLUMBER CAUTION! TWO PEOPLE ARE REQUIRED TO LIFT THE BATHTUB QUESTIONS ON PRODUCT, INSTALLATION, RETURNS? PLEASE CONTACT streamlinebath.com support@streamlinebath.
WARRANTY RETURNS We thank you for your purchase. Here at Streamline®, our goal is to provide customers with exceptional bathroom and kitchen products. We understand that things sometimes don’t work out. If you are unsatisfied with your Streamline® product and would like to initiate a return, please reach out to support@streamlinebath.com .
PRIOR TO INSTALLING These products must be installed by a fully insured and licensed plumber only. Installation of any product by anyone other than fully insured and licensed plumber shall void limited warranty. We are not responsible for any local code compliance for this product. Building and plumbing codes may vary state-to-state. Streamline shall not be held liable for any and all incidental damages or flood caused due to use of this product.
DRAIN MODEL COMPATIBILITY ACRYLIC FREESTANDING BATHTUB R-5040-67CIFSBCH-FM R-5041-67CIFSPCH-FM R-5042-67CIFSWH-FM R-5043-67CIFSRDY-FM R-5080-66CIFSWH-FM R-5081-60CIFSWH-FM R-5140-66CIFSWH-FM R-5180-72CIFSWH-FM R-5200-72CIFSWH-FM R-5201-61CIFSWH-FM R-5300-71CIFSWH-FM R-5320-67CIFSGR-FM R-5340-66CIFSGLD-FM R-5360-72CIFSBCH-FM R-5380-67CIFSGLD-FM R-5381-67CIFSBCH-FM R-5480-60CIALWH-FM R-5260-67CIFSGLD-FM R-5400-67CIFSWH-FM N-DWF-CH N-DWF-GLD Model Model A1866
DRAIN DIAGRAMS No 13 12 12 16 15 14 11 10 1 2 3 4 5 6 7 9 8 Model A1866 13 ITEM Qty 1 Cover 1 2 Cover gasket 1 3 Cartridge 1 4 Strainer 1 5 Waste upper gasket 1 6 Waste lower gasket 1 7 Connector 1 8 Coupling nut 1 9 Nut 1 10 Washer 3 11 Tee 3 12 Pipe 1 13 Overflow body 1 14 Tapered rubber gasket 1 15 Overflow upper gasket 1 16 Overflow plate 1 17 Pin Bolt 1 16 Taic piece 1 17 Flange 1
DRAIN DIAGRAMS No Model: N-DWF-GLD Model: N-DWF-CH ITEM Qty 1 Cover 1 2 Cover gasket 1 3 Cartridge 1 4 Strainer 1 5 Waste upper gasket 1 6 Waste lower gasket 1 7 Connector 1 8 Coupling nut 1 9 Nut 1 10 Washer 3 11 Tee 3 12 Pipe 1 13 Overflow body 1 14 Tapered rubber gasket 1 15 Overflow upper gasket 1 16 Overflow plate 1 17 Pin Bolt 1 16 Taic piece 1 17 Flange 1
BATHTUB INSTALLATION 1. Ensure that the floor at the installation site has sufficient floor support and is level. 2. Waterproofing the floor is highly recommended. 3. Determine the location of the drainpipe on the floor by taking measurements of the drain and waste location underneath the unit. Clean the drain hole area in preparation of setting the drain. The area should be dry & free from any debris. 4. Remove the bathtub from its box.
5. Gently place the bathtub in the upside-down position on a tarp or cardboard sheet in order to avoid contact with any rough surface. 6. Loosen the nuts & washers from the metal frame. Adjust the leveling feet to align with the bathtub’s bottom as well as the floor and then tighten the washer and nuts. 7. Ensure to mark all positions of leveling legs on the floor using a pencil. Move the bathtub into the desired location near the drainpipe.
8. Before proceeding with installation, push the pop up into a close position and fill the bathtub above the overflow [Note: some models may not have an overflow] to test for overflow and drain leakage. 9. Proceed to place the provided flexible drain hose into the floor drain. 10. Please note, the flexible hose is a basic way that we provide to connect to the end plumbing in a home.
12. Apply silicone along the bottom of the bathtub In order to create an airtight seal. Then apply a bead of tub & tile caulk around the edges of the base. 13. With the bathtub now in place, wipe off any excess silicone, tub & tile caulk where the bathtub meets the floor. 14. Allow for up to 24 hours for the adhesive material to set.
8. Take the strainer, place silicone sealant around it, and then place it into the drain hole ensuring a tight connection with the drain ell & gasket. Use silicone sealant. DO NOT use plumbers putty to seal. Silicone Sealant Strainer Gasket Drain Ell 9. Insert the tailpiece into the trap inlet using the O-ring, coupling nut, & flange. The tailpiece may need to be cut for proper fit. 1''-2'' of the tail piece shoudl fit inside the trap. Slip the flange over the tailpiece and slide down to the floor.
11 . Attach the tapered rubber gasket to the overflow ell. Align the overflow ell with the overflow hole & secure the drain to the tub with overflow plate and screw provided. Tapered Rubber Gasket Overflow Plate 12 . Make sure a watertight seal exists on all bath drain connections.
SINGLE HANDLE FREESTANDING TUB&SHOWER FAUCET H-120-TFMSHCH
RECOMMENDED TOOLS Screwdriver Channel Locks Goggles Hammer WARNING: Please keep the tool for future use! Adjustable Wrench Teflon tape Allen key ATTENTION: for easy installation, you will need: 1. To read all the installation instruction completely before beginning. 2. To read all the warning, attention and maitenance information.
FAUCET INSTALLATION 1. Drill one hole of 130mmx130mm max and drill 3 holes with 80mm diameter as shown. 80 mm 2. Align the base ① with the holes exactly as shown. 1 HOT WATER COLD WATER MAX 130mm 3. Insert the expansion anchors ① into the holes on the base ② with a hammer, tighten with adjustable wrench.
4. Connect hot and cold supply lines and test by opening water lines. HOT WATER COLD WATER 5. If there are no leaks, remove the 3 screws (1) with the Allen key (2), then remove plate (3) and nuts (4) as shown.
6. Connect hot water flexible hose(1) and cold water flexible hose(1) to the base (2) correctly as shown. 1 7. 2 Insert 3 screws (1) into holes on the plate (2), tighten with allen key (3).
CHECKING AND TESTING 1. Remove the aerator ② with aerator wrench, take out the o-ring ① too.Turn the faucet handle all the way on, turn on hot and cold water supply and flush water lines for one minute.Reinstall aerator with aerator wrench. 2. Check all connections at arrows for leaks, re-tighten it if necessary.
MAINTENANCE A. If there is splash or low flow rate,please remove the aerator with the wrench and clean the debris. B. If faucet leaks from the handle or drips from spout, please replace cartridge following the following steps: Disassemble the screw② with allenkey①, take out the handle③, then remove the trim cap④. 1. 4 3 2 1 2. Unscrew the cartridge nut① with adjustable wrench, then take out the old cartridge②. 1 2 3.
CLEANING AND CARE Daily cleaning and care are required in order to keep the product shining and properly working. 1. Clean it with water and dry it with soft cloth. 2. Clean the product with gentle liquid or glass cleaner. 3. Don't use acid cleaner. 4. Don't clean with abrasive material, abrasive paper or knife.
