UNDERMOUNT RANGE HOOD SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE RANGE HOOD For installation and assembly videos, please visit our website www.streamlinebath.com OR our YouTube page by searching for "Streamline Bath" OR following the below link to our channel: https://www.youtube.com/channel/UCII7TGMbkwoGSqzo-pGfaJw streamlinebath.com support@streamlinebath.
TABLE OF CONTENTS 1. Safety Disclaimer 3 2. Electrical Guidelines 7 3. Warranty Guidelines 8 4. Tools Required 10 5. Parts Supplied 11 6. Installation Dimensions 12 7. Ventilation Options 13 8. Installation Instructions 15 A: Recessed Installation 17 B: Wall Installation 25 9. Control Panel Operation 33 10. Product Care & Maintenance 37 11 LED Light Replacement & Charcoal Filter Installation 41 streamlinebath.com support@streamlinebath.
1. Safety Disclaimer • Please note that these installation instructions are intended as general guidelines only. It is recommended to seek advice from a professional installation specialist for the most suitable type of mounting hardware and support system based on the construction of your space. • Use this unit only in the manner intended by Streamline. If you have any questions, please contact Streamline. • The manufacturer cannot be held responsible for failing to comply with safety regulations.
• Before installing your range hood, it's essential to verify the local, city, and state regulations for the appropriate venting method. Many agencies have specific CFM (cubic feet per minute) rating specifications for hoods as well. Additionally, you may need to purchase additional items to ensure that the hood is vented in accordance with your local city and state specifications. Be sure to follow all regulations and guidelines to ensure safe and proper installation.
• Before drilling any holes, it is crucial to verify that the space behind the installation surface is free of any electrical cables, pipes, or other obstructions. • The stainless-steel surfaces of the range hood are highly susceptible to damage during installation if they are scratched or bumped by tools. Therefore, it is crucial to take necessary precautions to protect the surfaces while installing the range hood.
• Sufficient air is needed for proper combustion and exhaustion of gases to avoid back-drafting. Follow the heating equipment manufacturer’s guidelines and safety standards, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local municipal code guidelines. • Do not connect the appliance to flues (from boilers, fireplaces, etc.).
2. Electrical Guidelines Please ensure to observe all governing codes and ordinances when installing the range hood. Additionally, ensure that the electrical installation is adequate and complies with the latest edition of the National Electrical Code, ANSI/NFPA 70, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91, as well as all local codes and ordinances.
3. Warranty Guidelines LIMITED WARRANTY EXCLUSION ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITED MANUFACTURER’S WARRANTY All parts and finishes of Streamline® products are warranted to the original consumer purchaser to be free from defects in material and workmanship for a period of two to five years [depending on the product and model; please check the product listing or email us at support@streamlinebath.com if you are unsure] after the date of original retail purchase. Proof of the original purchase is required to obtain a remedy under this limited warranty.
4. Tools Required Electric Drill Utility Knife 5/16'' Drill Bit 5/32'' Drill Bit Screwdriver Pliers Tape Measure & Pencil Electrical Wiring ON OFF Aluminum Foil Tape/Duct Tape streamlinebath.com Hammer Jigsaw/Saber Saw support@streamlinebath.
5. Parts Supplied Range Hood Name Image 4x30 mm Mounting Screws Qty x9 5’’ Round Aluminum Duct x1 Flaps x1 Damper x1 Wall Anchors x9 Vent Cover x1 Charcoal Filter Set x1 (Length: 6.5 ft.) streamlinebath.com support@streamlinebath.
6. Installation Dimensions A Floor To Ceiling Height B Floor To Counter Top Height (Standard: 36’’) C Height of Counter Top to Range Hood Bottom (Minimum 26’’-30’’) D Kitchen Cabinet Height E Range Hood Installation Height [A-D-(B+C)] D E C C A A B streamlinebath.com B support@streamlinebath.
7. Ventilation Options There are three different options available for venting the range hood. It is recommended to seek guidance from a professional installer to choose the best installation method for your specific requirements. Ductless streamlinebath.com Wall Venting support@streamlinebath.
• We recommend installing the vent system before installing the range hood. • A damper is required in the venting system. If the wall or roof cap already has a damper, do not use the damper that comes with the range hood. • Ensure that the exhaust hose is fully extended to maximize airflow. • For the best results, it is advised to limit the length of the exhaust duct hose and the number of bends in the system to achieve optimal performance. • The ideal length of the duct system is between 35 and 40 feet.
8. Installation Instructions 1. The range hood should be carefully removed from its packaging. RANGE HOOD 2. Remove the protective blue/white film from the range hood. 3. Ensure that there are no components or packaging materials that may have become trapped or left inside the range hood and remove any, if necessary. streamlinebath.com support@streamlinebath.
4. Test to ensure that the range hood works by plugging it into an electrical outlet. 5. Check that all features are properly functioning and that the LED lights work. 6. Unplug the range hood. 7. Remove the mesh or baffle filters, depending on the range hood that was purchased. streamlinebath.com support@streamlinebath.
8. On the top right of the motor, there is a lever that you can use to switch between recirculating and ducted modes for the range hood. Loosen the lever from its current position and adjust it to the desired position. • For ducted mode, turn the lever to the RIGHT. • For ductless/recirculating mode, turn the lever to the LEFT. Recessed Installation 9. If you plan to use the provided template, affix the template with tape to the bottom of the cabinet.
10. Use a 5/16’’ [8mm] drill bit to make (4) pilot holes in the cabinet at the marked locations. For wood, use a 5/32'' drill bit. Drill 11. Insert the plastic wall anchors firmly into the four drilled holes. Plastic Anchors streamlinebath.com support@streamlinebath.
12. Insert the ST4*30 screws into the plastic wall anchors, leaving about 1/4 of an inch of the screw protruding from the cabinet. It will be tightened after the range hood is hung in the final step. Screws 13. Check for stability by mounting the range hood onto the screws and ensuring it fits tightly and securely. 14. Remove the range hood from the mounting screws. streamlinebath.com support@streamlinebath.
15. There are multiple ventilation choices available for the range hood: A B Venting through the roof: If you choose to vent through the roof, you will need to make an extra cutout of 5.25''(133mm) to accommodate the duct passing through the ceiling. C Venting through the wall: When venting through the wall, an extra cutout of 5.25'' (133mm) will need to be made to allow for the duct to be properly connected outside.
If installing using the ducted installation method, please follow the below steps. If using the ductless installation method, PLEASE SKIP and move to step #23. 16. Two holes need to be cut in the cabinet: one for the duct and another for the power cord. Use a saw or drill to create a circular hole in the bottom of the cabinet with a diameter of 5.25 inches. Drill a 1-1/2 inch hole into the bottom of the cabinet next to the vent hole to create an access hole for the power cord.
18. Attach the vent flaps in the exhaust port on the top of the range hood. Ensure that the flaps can open smoothly without any obstructions. Ensure that the bumps on the flap face upwards and outwards. Flaps 19. Connect the 5’’ round aluminum duct exhaust hose to the round vent air flap by placing one end of the hose over the flap and securing it with two small screws. Then, wrap the connection with tape or use a hose clamp and wrap it with tape to ensure a tight seal.
Side Vent Installation 20. If choosing to vent from the side, remove the backplate from the range hood. Using pliers, disassemble the metal panel by pulling it from left to right. Then, use the pliers to tear away the seal by pulling it outward. Pliers 21. Attach the square to round outlet damper (NOT INCLUDED IN PURCHASE) or rectangular damper (NOT INCLUDED IN PURCHASE). Square To Round Outlet Adaptor Rectangular Duct 22. Take the provided vent cover and place it on top of the venting cutout.
23. Pull the ductwork and electrical cord through the cabinet hole. If installing using the ductless installation method, please follow the below step. If using the ducted installation method, PLEASE SKIP and move to step #25. 24. Take the provided vent cover and place it on top of the range hood venting cutout. Rotate clockwise to tighten in place. Vent Cover 25. Lift and hang the range hood on the screws previously drilled. streamlinebath.com support@streamlinebath.
26. At the back of the range hood, right below the mounting holes, there will be 2 visible holes (1 on each side). These are additional safety holes to help secure the range hood in position. 1. Use a 5/16’’ [8mm] drill bit to make pilot holes in the cabinet at the marked locations. For wood, use a 5/32'' drill bit. 2. Fasten the range hood using (2) ST4*30 screws. 3. Tighten the four initial mounting screws that you drilled into the cabinet. Drill 1 2 3 27.
29. Plug in the range hood to the electrical outlet. Make sure that all operations are functioning properly. Wall Installation 1. Find the optimal height for mounting the range hood. For the best results, it is recommended to place it between 26 to 30 inches above the range. Once the ideal mounting height is determined, create a marking at a horizontal level. This will be for the bottom of the range hood.
2. If you plan to use the provided template, affix the template with tape to the wall, making sure that it aligns with the two previously drawn lines. Alternatively, you may also position the range hood along the vertical and horizontal lines and mark the location of the mounting holes on the wall. 3. Use a 5/16’’ [8mm] drill bit to make (2) pilot holes in the wall at the marked locations. For wood, use a 5/32'' drill bit. 4. Insert the plastic wall anchors firmly into the drilled holes.
5. Insert (2) ST4*30 screws into the plastic wall anchors, leaving about 1/4 inch of the screw protruding from the cabinet. It will be tightened after the range hood is hung. Screws 6. Check for stability by mounting the range hood onto the screws and ensuring it fits tightly and securely. 7. Remove the range hood from the mounting screws. streamlinebath.com support@streamlinebath.
If installing using the ducted installation method, please follow the below steps. If using the ductless installation method, PLEASE SKIP and move to step #13. 8. Take the provided damper and insert it into the top of the range hood venting cutout. Rotate clockwise to tighten in place. Damper streamlinebath.com support@streamlinebath.
9. There are multiple ventilation choices available for the range hood: A Venting through the roof: If you choose to vent through the roof, you will need to make an extra cutout of 5.25''(133mm) to accommodate the duct passing through the ceiling. streamlinebath.com B Venting through the wall: When venting through the wall, an extra cutout of 5.25'' (133mm) will need to be made to allow for the duct to be properly connected outside.
10. Attach the vent flaps in the exhaust port on the top of the range hood. Ensure that the flaps can open smoothly without any obstructions. Ensure that the bumps on the flap face upwards and outwards. Flaps Some under-mount range hood models may have a rectangular side vent cutout designed for side ventilation. Please check the specification sheet of the range hood or contact our customer service to confirm. streamlinebath.com support@streamlinebath.
Side Vent Installation 11. If choosing to vent from the side, remove the backplate from the range hood. Using pliers, disassemble the metal panel by pulling it from left to right. Then, use the pliers to tear away the seal by pulling it outward. Pliers 12. Attach the square to round outlet damper (NOT INCLUDED IN PURCHASE) or rectangular damper (NOT INCLUDED IN PURCHASE). Square To Round Outlet Adaptor Rectangular Duct 13. Take the provided vent cover and place it on top of the venting cutout.
If installing using the ductless installation method, please follow the below steps. If using the ducted installation method, PLEASE SKIP and move to step #8. 14. Take the provided damper and insert it into the top of the range hood venting cutout. Rotate clockwise to tighten in place. Vent Cover 15. Lift and hang the range hood on the previously drilled screws. streamlinebath.com support@streamlinebath.
16. At the back of the range hood, right below the mounting holes, there will be 2 visible holes (1 on each side). These are additional safety holes to help secure the range hood in position. 1. Use a 5/16’’ [8mm] drill bit to make pilot holes in the cabinet at the marked locations. For wood, use a 5/32'' drill bit. 2. Fasten the range hood using (2) ST4*30 screws. 3. Tighten the four initial mounting screws that you drilled into the cabinet. Drill 1 2 3 17.
19. Plug in the range hood to the electrical outlet. Make sure that all operations are functioning properly. streamlinebath.com support@streamlinebath.
9. Control Panel Operation Push Button 0 1 2 3 0 1 2 OFF Button Low Speed Button Medium Speed Button Starts the fan at low speed. Turns off the fan. Starts the fan at medium speed. 3 High Speed Button Starts the fan at high speed. Light Button Used for turning the light on or off. • To turn the range hood on, simply push the selected speed button (1,2,3). • To turn the range hood off, push the 0 button. • To turn the light on/off, press the LIGHT button.
26 37 Electronic Push Button Light Button Used for turning the light on or off. High Speed Button Medium Speed Button Starts the fan at high speed. Low Speed Button Starts the fan at low speed. Starts the fan at medium speed. OFF Button Turns off the fan. • To turn the range hood on, simply push the selected speed button. • To turn the range hood off, push the OFF button. • Pushing the OFF button once delays the turn off time by 1 minute. • Pushing the OFF button twice turns it off immediately.
Electronic Touch Panel 88:88 Light Button Used for turning the light on or off. Speed Button Changes the speed of the motor from high, medium, and low levels. streamlinebath.com Timer Allows for a delayed shutdown of the range hood. ON/OFF Button Turns the fan on or off. support@streamlinebath.
Electronic Touch Panel • To turn the range hood on, press the ON/OFF button. • To turn the range hood off, push the ON/OFF button. • Pressing the OFF button once delays the turn-off time by 1 minute. • Pressing the OFF button again will turn the range hood off immediately. • To turn the light on/off, press the LIGHT button. The LIGHT button works without having to push the ON/OFF button for the range hood. Selecting A Speed • To select the range hood speed, press the SPEED button.
10. Product Care & Maintenance streamlinebath.com support@streamlinebath.
streamlinebath.com support@streamlinebath.
streamlinebath.com support@streamlinebath.
CHARCOAL FILTERS: streamlinebath.com support@streamlinebath.
11. LED Light & Charcoal Filter Replacement LED LIGHT REPLACEMENT 1. Before proceeding, ensure that the range hood is turned off and disconnected from any electrical supply. 2. Remove the mesh or baffle filters, depending on the range hood that was purchased. streamlinebath.com support@streamlinebath.
3. The electrical wire for the LED lights can be found behind the light fixtures. 4. The wires for the LED lights are connected using a snap-down connector. To disconnect the LED lights, press down on the connector and gently pull the opposing electrical wire away from the connector. 5. Take out the LED light by pressing the long silver bar that covers the LED. • Push the LED outwards and downwards. streamlinebath.com support@streamlinebath.
6. Insert the new LED lights into the opening inwards and upwards and apply gentle pressure until you hear a click and feel the light sitting securely in place. 7. Reconnect the electrical wiring in the range hood with the LED snap connector. 8. Test to make sure that the lights are working properly. streamlinebath.com support@streamlinebath.
9. Place the filters back into their original position. 9. Turn the range hood back on. 0 streamlinebath.com 1 2 3 support@streamlinebath.
CHARCOAL FILTER INSTALLATION AND REPLACEMENT 1. Remove the mesh or baffle filters, depending on the range hood that was purchased. 2. The placement of the charcoal filter varies depending on the model. In some models that only require 1 charcoal filter, the opening is in the middle of the motor. For models that require 2 charcoal filters, the openings are positioned on the sides of the motor.
3. Take one filter and attach it to the motor. Rotate and twist it clockwise until it locks in place. If your range hood model calls for two filters to be installed, then the filters should be installed on each side. Repeat the previous step by taking another charcoal filter and attaching it to the other side of the motor. Rotate and twist it clockwise until it locks in place. Left Filter Right Filter 4. To replace the filter, rotate it counterclockwise and then remove it.
