WALL MOUNT RANGE HOOD SERIES OWNER'S MANUAL & INSTALLATION GUIDE READ ENTIRE INSTALLATION GUIDE PRIOR TO INSTALLING THE RANGE HOOD For installation and assembly videos, please visit our website www.streamlinebath.com OR our YouTube page by searching for "Streamline Bath" OR following the below link to our channel: https://www.youtube.com/channel/UCII7TGMbkwoGSqzo-pGfaJw streamlinebath.com support@streamlinebath.
TABLE OF CONTENTS 1. Safety Disclaimer 3 2. Electrical Guidelines 7 3. Warranty Guidelines 8 4. Tools Required 10 5. Parts Supplied 11 6. Installation Dimensions 12 7. Ventilation Options 13 8. Installation Instructions 15 A: Recessed Installation 17 B: Wall Installation 25 9. Control Panel Operation 33 10. Product Care & Maintenance 37 11 LED Light Replacement & Charcoal Filter Installation 41 streamlinebath.com support@streamlinebath.
1. Safety Disclaimer • Please note that these installation instructions are intended as general guidelines only. It is recommended to seek advice from a professional installation specialist for the most suitable type of mounting hardware and support system based on the construction of your space. • Use this unit only in the manner intended by Streamline. If you have any questions, please contact Streamline. • The manufacturer cannot be held responsible for failing to comply with safety regulations.
• Before installing your range hood, it's essential to verify the local, city, and state regulations for the appropriate venting method. Many agencies have specific CFM (cubic feet per minute) rating specifications for hoods as well. Additionally, you may need to purchase additional items to ensure that the hood is vented in accordance with your local city and state specifications. Be sure to follow all regulations and guidelines to ensure safe and proper installation.
• Before drilling any holes, it is crucial to verify that the space behind the installation surface is free of any electrical cables, pipes, or other obstructions. • The stainless-steel surfaces of the range hood are highly susceptible to damage during installation if they are scratched or bumped by tools. Therefore, it is crucial to take necessary precautions to protect the surfaces while installing the range hood.
• Sufficient air is needed for proper combustion and exhaustion of gases to avoid back-drafting. Follow the heating equipment manufacturer’s guidelines and safety standards, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local municipal code guidelines. • Do not connect the appliance to flues (from boilers, fireplaces, etc.).
2. Electrical Guidelines Please ensure to observe all governing codes and ordinances when installing the range hood. Additionally, ensure that the electrical installation is adequate and complies with the latest edition of the National Electrical Code, ANSI/NFPA 70, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91, as well as all local codes and ordinances.
3. Warranty Guidelines LIMITED WARRANTY EXCLUSION ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITED MANUFACTURER’S WARRANTY All parts and finishes of Streamline® products are warranted to the original consumer purchaser to be free from defects in material and workmanship for a period of two to five years [depending on the product and model; please check the product listing or email us at support@streamlinebath.com if you are unsure] after the date of original retail purchase. Proof of the original purchase is required to obtain a remedy under this limited warranty.
4. Tools Required Electric Drill Utility Knife 5/16'' Drill Bit 5/32'' Drill Bit Screwdriver Pliers Tape Measure & Pencil Electrical Wiring ON OFF Aluminum Foil Tape/Duct Tape streamlinebath.com Hammer Jigsaw/Saber Saw support@streamlinebath.
5. Parts Supplied Range Hood Name Image Qty 4x30 mm Mounting Screws x 11 3x10 mm Mounting Screws x4 Wall Anchors x 11 Wall Mount Bracket x1 Inner Chimney Bracket x1 Outer Chimney Bracket x1 6’’ Round Aluminum Duct x1 Oil Tray x1 (Length: 6.5 ft.) (ONLY FOR T-451-SERIES) x1 Charcoal Filter Set streamlinebath.com support@streamlinebath.
6. Installation Dimensions A Floor To Ceiling Height B Floor To Counter Top Height (Standard: 36’’) C Height of Counter Top to Range Hood Bottom (Minimum 26’’-30’’) D Range Hood Height E Duct Cover Height [F-D] F Range Hood Installation Height [A-(B+C)] E F D C A A B streamlinebath.com C B support@streamlinebath.
7. Ventilation Options There are three different options available for venting the range hood. It is recommended to seek guidance from a professional installer to choose the best installation method for your specific requirements. Ductless Wall Venting Roof Venting A A B A B B A: Charcoal Filters A: Wall Cap A: Roof Cap B: Venting Holes B: 6" Round Duct B: 6" Round Duct streamlinebath.com support@streamlinebath.
• We recommend installing the vent system before installing the range hood. • A damper is required in the venting system. If the wall or roof cap already has a damper, do not use the damper that comes with the range hood. • Ensure that the exhaust hose is fully extended to maximize airflow. • For the best results, it is advised to limit the length of the exhaust duct hose and the number of bends in the system to achieve optimal performance. • The ideal length of the duct system is between 35 and 40 feet.
8. Installation Instructions 1. Find the optimal height for mounting the range hood. For the best results, it is recommended to place it between 26 to 30 inches above the range. 26”- 30” 2. Once the ideal mounting height is determined, create a marking at a horizontal level. This will be the bottom of the range hood. Marker streamlinebath.com support@streamlinebath.
3. Locate the vertical centerline on the wall in reference to the horizontal line, marking the position where the range hood will be mounted. This line will reflect the center point. Marker 4. Take the range hood out of its packaging. RANGE HOOD 5. Remove the protective blue/white film from the range hood. streamlinebath.com support@streamlinebath.
6. Ensure that there are no components or packaging materials that may have become trapped or left inside the range hood, and remove any, if necessary. 7. Verify the correct operation of all functions and features by plugging the range hood into an electrical outlet. 8. Unplug the range hood. streamlinebath.com support@streamlinebath.
9. If using the cutout template that came with the range hood, use it to mark the location of the mounting bracket by lining up the template with the 2 previously marked lines. Affix the template to the wall using tape. Make sure to align the centerline and bottom of the template with the corresponding markings on the wall for the range hood. Use a pencil to trace and mark the position of the mounting bracket.
10. Place the mounting bracket against the previously marked spot and mark the centers of the 3 mounting screw locations for the bracket on the wall. Marker 11. Use a drill to make three holes in the wall at the marked locations. For wood, use a 5/32'' drill bit, and for wall anchors, use a 5/16'' drill bit. Drill streamlinebath.com support@streamlinebath.
12. If mounting directly to a wood stud, use the (3) provided ST 4x30 mounting screws to secure the mounting bracket in place by drilling (3) pilot holes. If mounting to the wall, use the (3) provided wall anchors prior to installing the (3) ST 4x30 mounting screws. Insert the plastic wall anchors firmly into the drilled holes. Plastic Anchors Screws 13. Secure the mounting bracket with the selected method of choice. Wood Stud Wall Wall Anchor Mounting Screw Mounting Bracket streamlinebath.
14. Mount the range hood onto the mounting bracket. 15. Remove the mesh or baffle filters, depending on the range hood purchased. 16. At the back of the range hood, there will be 2 visible holes. Mark their position on the wall and remove the range hood from the mounting bracket. Marker streamlinebath.com support@streamlinebath.
17. Use a drill to make two holes in the wall at the marked locations. For wood, use a 5/32'' drill bit, and for wall anchors, use a 5/16'' drill bit. If mounting directly to a wood stud, use the (2) provided ST 4x30 mounting screws to secure the mounting bracket in place by drilling (2) pilot holes. If mounting to the wall, use the (2) provided wall anchors prior to installing the (2) ST 4x30 mounting screws. Insert the plastic wall anchors firmly into the drilled holes. Plastic Anchors Drill 18.
19. Fasten the range hood using (2) ST 4x30 screws. Screws If installing using the ducted installation method, please follow the below steps. If using the ductless installation method, PLEASE SKIP and move to step 25. 20. Re-insert either the mesh or baffle filters into the range hood. 21. Remove the protective tape from the damper. streamlinebath.com support@streamlinebath.
22. Ensure that the damper is correctly installed. Attach the vent flaps in the exhaust port on the top of the range hood. Check to make sure that the flaps can open smoothly and without any obstructions. Please note that the bumps on the flaps should face upwards and outwards. 23. Attach a 6-inch round aluminum duct exhaust hose to the round vent air flap and secure it with two small screws, as well as tape or a hose clamp with tape. Exhaust Hose Small screws Tape 24.
If installing using the ductless installation method, please follow the below steps. If using the ducted installation method, PLEASE SKIP and move to chimney installation. 25. Attach the charcoal filters. For detailed instructions on how to attach the charcoal filters, please visit Section 11 on page 45. 26. Re-insert either the mesh or baffle filters into the range hood.
1. Please note that the longer bracket is the upper chimney bracket. The shorter bracket is the lower chimney bracket. Upper Chimney Bracket Lower Chimney Bracket 2. To distinguish between the lower and upper chimneys, note that the upper chimney will feature vents on the side of the chimney. The venting holes near the top of the inner (upper) chimney should be exposed from the outer (lower) chimney. Inner (Upper) Chimney Outer (Lower) Chimney 3.
4. Slide the lower chimney onto the range hood and ensure it is securely in place and level with the range hood. Outer (Lower) Chimney 5. Mark the location of the mounting bracket on the wall. Remove the mounting bracket from the lower chimney. Marker 6. Position the lower chimney mounting bracket against the marked spot and mark the center of the 2 mounting screw locations on the wall. Marker streamlinebath.com support@streamlinebath.
7. For wood, use a 5/32'' drill bit, and for wall anchors, use a 5/16'' drill bit. Drill 8. If mounting directly to a wood stud, use the (2) provided ST 4x30 mounting screws to secure the mounting bracket in place by drilling (2) pilot holes. Screws 9. If mounting to the wall, use the (2) provided wall anchors prior to installing the (2) ST 4x30 mounting screws. Insert the plastic wall anchors firmly into the drilled holes. Plastic Anchors streamlinebath.com support@streamlinebath.
10. Attach the upper chimney bracket to the upper chimney. Tape Upper Chimney 11. Slide the outer chimney over the lower chimney. Inner (Upper) Chimney Outer (Lower) Chimney 12. Lift the upper chimney to the ceiling and mark on the wall the position of the upper chimney mounting bracket. Make sure that the markings align with the centerline that was previously marked. Marker streamlinebath.com support@streamlinebath.
When venting through the wall, please note that it is NOT required for the chimney to make contact with the ceiling. 13. Remove the upper chimney. Position the upper chimney mounting bracket against the marked spot and mark the center of the 2 mounting Marker 14. For wood, use a 5/32'' drill bit, and for wall anchors, use a 5/16'' drill bit. Drill streamlinebath.com support@streamlinebath.
15. If mounting directly to a wood stud, use the (2) provided ST 4x30 mounting screws to secure the mounting bracket in place by drilling (2) pilot holes. If mounting to the wall, use the (2) provided wall anchors prior to installing the (2) ST 4x30 mounting screws. Insert the plastic wall anchors firmly into the drilled holes. Screws Plastic Anchors 16. Re-slide the inner and outer chimneys on the range hood. streamlinebath.com support@streamlinebath.
17. To attach the upper chimney, lift it onto the upper support bracket and use one ST 4x10 screw on each side of the chimney to secure in place. Screws 18. Alternatively, you may hang the chimney on the support bracket. 19. Some range hood models may be equipped with screw holes at the bottom of the lower chimney. Use (2) [1 on each side] 4x10 mm screws to tighten and secure. Screws streamlinebath.com support@streamlinebath.
9. Control Panel Operation Push Button 0 1 2 3 0 1 2 OFF Button Low Speed Button Medium Speed Button Starts the fan at low speed. Turns off the fan. Starts the fan at medium speed. 3 High Speed Button Starts the fan at high speed. Light Button Used for turning the light on or off. • To turn the range hood on, simply push the selected speed button (1,2,3). • To turn the range hood off, push the 0 button. • To turn the light on/off, press the LIGHT button.
26 Electronic Push Button Light Button Used for turning the light on or off. High Speed Button Medium Speed Button Starts the fan at high speed. Low Speed Button Starts the fan at low speed. Starts the fan at medium speed. OFF Button Turns off the fan. • To turn the range hood on, simply push the selected speed button. • To turn the range hood off, push the OFF button. • Pushing the off button once delays the turn off time by 1 minute. • Pushing the OFF button twice turns it off immediately.
Electronic Touch Panel 88:88 Light Button Used for turning the light on or off. Speed Button Changes the speed of the motor from high, medium, and low levels. streamlinebath.com Timer Allows for a delayed shutdown of the range hood. ON/OFF Button Turns the fan on or off. support@streamlinebath.
Electronic Touch Panel • To turn the range hood on, press the ON/OFF button. • To turn the range hood off, push the ON/OFF button. • Pressing the OFF button once delays the turn-off time by 1 minute. • Pressing the OFF button again will turn the range hood off immediately. • To turn the light on/off, press the LIGHT button. The LIGHT button works without having to push the ON/OFF button for the range hood. Selecting A Speed • To select the range hood speed, press the SPEED button.
10. Product Care & Maintenance streamlinebath.com support@streamlinebath.
streamlinebath.com support@streamlinebath.
streamlinebath.com support@streamlinebath.
CHARCOAL FILTERS: streamlinebath.com support@streamlinebath.
11. LED Light & Charcoal Filter Replacement LED LIGHT REPLACEMENT 1. Before proceeding, ensure that the range hood is turned off and disconnected from any electrical supply. 2. Remove the mesh or baffle filters, depending on the range hood that was purchased. streamlinebath.com support@streamlinebath.
3. The electrical wire for the LED lights can be found behind the light fixtures. 4. The wires for the LED lights are connected using a snap-down connector. To disconnect the LED lights, press down on the connector and gently pull the opposing electrical wire away from the connector. 5. Take out the LED light by pressing the long silver bar that covers the LED. Push the LED outwards and downwards. streamlinebath.com support@streamlinebath.
6. Insert the new LED lights into the opening inwards and upwards and apply gentle pressure until you hear a click and feel the light sitting securely in place. 7. Reconnect the electrical wiring in the range hood with the LED snap connector. 8. Test to make sure that the lights are working properly. streamlinebath.com support@streamlinebath.
9. Place the filters back into their original position. 9. Turn the range hood back on. 0 streamlinebath.com 1 2 3 support@streamlinebath.
CHARCOAL FILTER INSTALLATION AND REPLACEMENT 1. Remove the mesh or baffle filters, depending on the range hood that was purchased. 2. The placement of the charcoal filter varies depending on the model. In some models that only require 1 charcoal filter, the opening is in the middle of the motor. For models that require 2 charcoal filters, the openings are positioned on the sides of the motor.
3. Take one filter and attach it to the motor. Rotate and twist it clockwise until it locks in place. If your range hood model calls for two filters to be installed, then the filters should be installed on each side. Repeat the previous step by taking another charcoal filter and attaching it to the other side of the motor. Rotate and twist it clockwise until it locks in place. Left Filter Right Filter 4. To replace the filter, rotate it counterclockwise and then remove it.
