Instructions / Assembly

ManualsBrandsStrip-N-Flash ManualsBuilding materials16 in. x 75 ft. Through Wall Flashing 2-rolls

Mortairvent

• Apply a weather resistant barrier over sidewall sheathing. Note: some regions may require two

layers of weather resistant barrier. Check local codes for more information.

• Install Mortairvent® after windows and doors have been properly installed and flashed

• Starting at the base of the wall, unroll Mortairvent® from right to left with the fabric flap on the

bottom. The blue geomatrix should be facing the weather resistant barrier and the filter fabric

facing the exterior of the building.

• Staple or nail every three square feet.

• On the bottom and top course only, fold the fabric flap and tuck it between the (blue) polymer

matrix and the weather resistant barrier to create an insect screen. The top course roll will need

to be inverted to achieve this.

• On subsequent courses, butt the blue polymer material together without overlapping. Pull the

fabric flap over the previous course (shingle style) and staple.

• Apply lath, scratch coat, and stucco or masonry veneer siding over Mortairvent® using

recommended fasteners and spacing.

CedAir-Mat

• Install plywood roof sheathing onto rafters. Install roofing felt or ice dam protection membrane

over sheathing. Check local codes and manufacturer’s recommendations for specific

requirements.

• Install CedAir-Mat® over roofing felt, ice protection membrane, and metal edge flashing or drip

edge. Ensure CedAir-Mat® material is installed flush against edge of the flashing or drip edge.

Carefully trim the CedAir-Mat® material at all penetrations with a utility knife or scissors.

• When installing cedar or alternate material shingles, unroll CedAir-Mat® horizontally just ahead

of the shingles as they are installed. Tack or nail CedAir-Mat® in place every three square feet.

Do not overlap the CedAir-Mat® material. Butt each course tightly against the previous course

and at vertical seams.

• At ridge locations, extend CedAir-Mat® material over the ridge and butt against the material on

the opposite side of the roof. If a ridge vent is utilized, follow the ridge vent manufacturer’s

recommendations for underlayment material installation.

• Apply roofing materials using manufacturer’s recommended fasteners and instructions, allowing

for the additional 3/8″ thickness of the CedAir-Mat® material.

Summary of content (4 pages)

PAGE 1
Mortairvent • • • • • • • Apply a weather resistant barrier over sidewall sheathing. Note: some regions may require two layers of weather resistant barrier. Check local codes for more information. Install Mortairvent® after windows and doors have been properly installed and flashed Starting at the base of the wall, unroll Mortairvent® from right to left with the fabric flap on the bottom.
PAGE 2
Advanced Drain • • Install composite drainage mats in accordance with manufacturer’s instructions at locations indicated on the Drawings. Install composite drainage mats: -To allow flow of water in all directions within drainage core. - To prevent soil from entering drainage core while providing ample flow of water. • • • • Secure composite drainage mats to surfaces with construction adhesive or termination bars in accordance with manufacturer’s instructions.
PAGE 3
Watairvent Furring Strips Installation over 1/2″ OSB or plywood intended for clapboard siding • Install your weather resistant barrier (WRB) of choice over the surface area of the sheathing. Be sure to tape all seams. • Place Watairvent® Furring Strip horizontally at the base of the wall around the entire perimeter (Diagram A) to prevent bugs from entering the channel. • Place the Watairvent® Furring Strips vertically every sixteen inches on center aligned with the wood studs (Diagram A).
PAGE 4
Strip-N-Flash • Surface Preparation: Concrete shall be in place for 7 days minimum. Substrate must be completely dry. Surface shall have a smooth finish free of voids, sharp protrusions, laitance and form release agents. Block or brick walls shall have mortar joints struck flush. • Primer: Surfaces to receive Strip-N-Flash™ must be clean and dry. For best results, concrete, masonry and some exterior gypsum substrates require coating with Primer. Apply Primer per manufacturer’s recommendations.