Picture similar Digital Terrestrial Receiver SRT 5003 User manual Bedienungsanleitung Manuel d’Utilisateur Manuale Utente Manual del usuario Návod k obsluze Upute za korištenje
PART 1 • English 1.0 Instruction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories: 2 2 3 3 4 2.0 Connection 2.1 Connecting to TV and Terrestrial Antenna 2.2 Connecting to a Digital Audio Amplifier 4 4 4 3.0 Your Receiver 3.1 Front Panel 3.2 Rear Panel 3.3 Remote Control 3.4 Default PIN- code: 0000 4 4 4 4 5 4.0 First Time Installation 5 5 5 7 8 10 11 6.0 OPERATION 6.1 Changing Channels 6.2 Accessing the Electronic Program Guide (EPG) 6.
PART 1 • English 1.0 Instruction 1.1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Heat-Never use or store this product near any heat source such as a radiator heat register, stove, or any type of equipment or appliance that generates heat, including stereo amplifiers. Servicing-Refer all servicing to qualified personnel. Attempting to remove the covers or disassemble the product, could expose you to dangerous high voltage points. Damage Requiring Service- If you notice any of the conditions described below while using a specified AC adapter.
PART 1 • English 1.4 Accessories: 1. 1 User Manual 2. 1 Remote control unit 3. 2x Batteries (AAA type) Note: The batteries should not be recharged, disassembled, electrically shortcircuited or be mixed or used with other types of batteries. If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH) types with low self-discharge to ensure long time operation of remote control. 2.0 Connection 2.
PART 1 • English INFO Shows the actual channel information VOL+/VOL- Volume up/down MENU Opens the main menu/In menu you will get one step back EXIT Exits from the menu or sub-menu pq Menu Off: Change channel to previous/next. Menu On: Moves the cursor up/down. 10. tu Menu Off: Increases/decreases the volume level. Menu On: Change settings for specific Menus 11. OK Menu On: Activates the highlighted menu item. Menu Off: Displays the current channel list 12. RECORD No function 13.
PART 1 • English 5.1.1 TV Channel list 1. I n Channel submenu select TV Channel List with the qp buttons and press OK to enter. 2. Use the tu buttons to change channel group (assumed you have already set up Favourite groups). 3. With the qp buttons select the channel you want to watch. With OK you can watch the selected channel in full screen mode. Edit Use this menu to favour, lock, skip, delete and rename channel list. Press numeric button [1] to enter edit menu.
PART 1 • English English Move Press the [4] button to activate the Move function. The selected channel will be marked in a symbol p q, use the qp buttons to move the selected channel to the desired position. Press OK, with tu select Yes in the confirmation window and press [4] to save. 5.1.
PART 1 • English start scan. After Channels are found, they will be stored and receiver switches to the first one saved in the list. 5.2.3 Antenna Setting 1. 2. 3. 4. Press MENU to enter main menu. se the qp buttons to select Installation, press OK to enter the menu. U With the qp buttons select Antenna setting and press OK to enter. Press the tu buttons to change setting. If On is selected, the receiver will provide 5V antenna power (for active antennas). 5. Press EXIT button to exit. 5.2.
PART 1 • English English GMT Offset: This menu is valid only when selected "User Define" in GMT Usage menu. The GMT offset range is "-11:30 ~ +12:00", increasing by half hours progressively. Date/Time: "Date" and "Time" menus are valid only when selected "Off" in GMT Usage menu. Press OK then numeric button to change the date and time. Time Display: This menu allow to control whether the time is displayed on screen or not. The options are: Off/On. 5.3.
PART 1 • English 5.3.8 Auto Standby This option allows you to enable or disable Auto Standby. The default setting for Auto Standby is ON. The receiver will switch to standby automatically when it doesn’t receive commands from the remote control for three hours. To avoid the automatic switch off, set Auto Standby to OFF. 5.4 Tools Press MENU button to enter Main Menu. Select “Tools” with the pq buttons and press OK to enter. 1. Press pq buttons to highlight the desired menu and press OK to enter. 2.
2. P ress pq buttons to select “Upgrade by Storage” item and press OK button, you are asked to input password. 3. Input the correct password (the default password is 0000), Software Upgrade submenu is opened. Then select the correct software file and press OK to start. Message will be displayed to confirm update process, select “Yes” to confirm or “No” to cancel. 4. Press EXIT” button to exit.
PART 1 • English Selected by number Enter the channel number directly by pressing numeric buttons, and press the OK button to select desired channel. Selected by on-screen channels list You can also select the required channel directly from on-screen channel list. This is displayed using the receiver’s main menu. See chapter 5.1.1 TV Channel list in this manual for operation detail. Alternatively you can call up channel list by pressing OK in viewing mode.
PART 1 • English Possible cause What to do Channel is scrambled Select alternative channel No response to remote control Receiver off Remote not aimed correctly Front panel obstructed Remote batteries exhausted Plug in and turn on plug Aim remote at front panel Check for obstructions Replace remote batteries Forgotten PIN code English Problem Scrambled channel message Contact local Service Hotline or send email to our Support via www.strong.
PART 1 • English Multimedia: Video playback: Audio playback: Picture view: MPEG-1 and MPEG-2 encoded (mpg) MP3 and WMA formats JPEG format Memory and System: Flash memory: 1 MByte SDRAM: 8 MBytes Connectors: ANT IN: IEC Female TO TV: IEC Male TV SCART (RGB, CVBS) S/PDIF: coaxial output USB port: max. 5 V/500 mA General Data: Supply Voltage: 220 – 240 V AC (SMPS), 50/60 Hz Power Consumption: 4.20 W (typ.), 5 W (max) Power consumption in Standby: 0.