Picture similar Digital Satellite Receiver SRT 6201 User Manual
PART 1 • English 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 2 3 3 3 2.0 Your Receiver 2.1 Rear Panel 2.2 Remote Control Unit 2.3 Default PIN code: 0000 3 3 4 4 3.0 Connections 3.1 Basic connection with SCART cable 3.2 Connecting to Satellite Dish 3.3 Connecting USB device 4 4 4 4 4.0 Starting up 4.1 Language Selection 4.2 Select Satellite 4.3 Antenna mode 5 5 5 5 5.0 Main Menu 5.1 Channel Organiser 5.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 1.3 Equipment Set-up English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: n Refer to the user manual of your TV and your antenna. n Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow.
PART 1 • English 2.2 Remote Control Unit Fig. 3 Turns the receiver On/Stand-by. Mutes audio output of the receiver. 0~9 Changes channel and controls numeric functions AV Toggles between TV and receiver (AV) mode TV/R Toggles between TV or radio mode MENU Shows the main menu and exits from any level of menu to view mode EXIT Exits from the menu or sub-menu and cancels the progressing function if applicable. pq Changes the current program to the previous/next program in TV mode.
PART 1 • English 4.0 Starting up English Ensure your satellite signal is of good quality. It is recommended that you perform the first time installation following the Installation Wizard step by step. It will help you to easily achieve system configuration and channel installation. 4.1 Language Selection Press pq to choose your language, press OK to confirm. The Select Satellite menu will appear. Future installation steps are depending from satellite where your dish is aimed. 4.
PART 1 • English or South. Choose field Goto Position and press OK. Your dish will be turned to the position of satellite. Then choose NEXT and press OK. The Channel Setup menu will appear. Choose NEXT and press OK to start the scan. When the scan is completed, the receiver will save the services information automatically and exit to the normal play state. 5.0 Main Menu All the important settings and features of your receiver can be operated in Main Menu.
Add satellite Press RED button, a satellite list will appear. Press tu to select the satellite. If the satellite is not in the list, select “NEW SAT1”. After selection of a satellite, the Configure Antenna menu will appear. Please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode. Further steps of installation are described in 4.2.
PART 1 • English 5.3.1 Preference 5.3.1.1 Language Setting You can change the language of the OSD, preferred audio and subtitles. Use pq to select the OSD language, Audio language or Subtitles language. Press OK or u to enter the language list and press pq to select the language. Press OK to confirm. 5.3.1.2 TV settings You can set the TV mode, Screen mode and Video output settings.. TV mode Press OK or u to select mode and OK to confirm. If you don’t know which standard your TV has, select AUTO.
Channel Lock Set the system channel lock to ON or OFF. If lock is ON, the parental PIN code needs to be entered to watch the locked channel. Menu Lock Press OK to select whether the menu should be locked or not (YES or NO), press OK to confirm. If the menu lock is ON, you need to enter the PIN for some operations such as search program and set factory default. Parental Setting If a channel is locked, the parental PIN code needs to be entered to watch the locked channel.
PART 1 • English e) File “Idapp1.ssu” will be created on USB device if “Loader + App” has been selected resp. file “userdb.ssu” if “User Database” has been selected. n To restore user data a) Connect USB device with backup of database to USB port of receiver. b) Go to System Setting – System Update and select “Update by USB”. c) Select a file with database backup (by default name of the file “userdb.ssu”) and press OK. d) Confirm update.
PART 1 • English 6.0 Watching TV and listening to the radio In normal operation status (no menu operation), press INFO. The program information banner will be displayed showing channel number, channel name, current, next program name (if available from broadcast) and current time. To check technical information about channel press INFO twice.
PART 1 • English 6.4 Selection Audio Language Press AUDIO to select the audio language. Select Audio Channel or Sound mode with pq and Audio channel number or Sound mode (Stereo, Left or Right channel). Press OK to confirm your selection. Your selection will be memorized for current channel. Receiver will play always the last selected audio track when you select this channel in future.
No picture Cause The receiver can’t receive the signal Incorrect values of some tuner parameters. Wrong direction of the dish Receiver tries to start-up, switches ON/OFF/ON/OFF… or displays “LOAD” Receiver detected short cut in your cable system or detected “Antenna Power Overload”. The remote control does not work The batteries of the remote control are not inserted or exhausted The USB storage device is not recognized. The external USB HDD does not start. The receiver switches off automatically.
PART 1 • English 09 Mar 2010 15:12 14