Picture similar Digital Satellite Receiver SRT 6200/SRT 6202/SRT 6205 User Manual 1.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 2 3 3 3 2.0 Your Receiver 2.1 Rear Panel 2.2 Remote Control Unit 2.3 Default PIN code: 0000 3 3 4 5 3.0 Connections 3.1 Basic connection with SCART cable 3.2 Connecting to Satellite Dish 3.3 Connecting USB device 5 5 5 5 4.0 Starting up 4.1 Language Selection 4.2 Select Satellite 4.3 Antenna mode 5 5 5 6 5.0 Main Menu 5.1 Channel Organiser 5.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 1.3 Equipment Set-up English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: n Refer to the user manual of your TV and your antenna. n Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow.
PART 1 • English 5. TV SCART To connect to your TV set using a SCART cable. 6. V CR SCART To connect to your DVD or video recorder using a SCART cable. The video signal will be looped through to your TV set if receiver is in stand-by mode.** 7. Video RCA To connect to your TV set using RCA cable* 8. Audio L/R RCA To connect to your TV set or amplifier using RCA cable* 9. S/PDIF Digital audio output To connect to the input of your digital audio amplifier. 10.
PART 1 • English Recording No function Play Fast backward Fast forward Stop English 4 1 6 7 3 2.3 Default PIN code: 0000 3.0 Connections 3.1 Basic connection with SCART cable Fig. 4 3.2 Connecting to Satellite Dish Connecting a fixed satellite dish to your receiver (Fig. 5) Connecting multiple fixed dishes to your receiver using a DiSEqC 1.0 switch (Fig. 6) 3.3 Connecting USB device Fig. 7 4.0 Starting up Ensure your satellite signal is of good quality.
PART 1 • English LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode. 4.3 Antenna mode a) Fixed dish Set Antenna mode to Fixed, select NEXT and press OK. The Adjust antenna screen appears. Select a transponder receivable at your location and adjust the antenna position for maximum signal strength and quality levels. When adjustment is completed, choose NEXT and press OK. The Channel Setup menu will appear. b) Dish mounted on DiSEqC 1.
PART 1 • English rate, Video PID, Audio PID. Press pq to highlight the desired channel, press tu to highlight “Move” and press OK to confirm selection of the channel. Use pq to move the channel to its new location and press OK to confirm. Repeat this for every channel you want to move. Delete channel Press pq to highlight the desired channel, press tu to highlight “Del” and press OK to mark the channel for deletion. Press EXIT and confirm the channel’s deletion by selecting OK and pressing OK.
PART 1 • English Use BLUE to set the scan type to NIT OFF or NIT ON if Blind Scan is set to OFF or to Quick Search or Detail Search if Blind Scan is set to ON. Once set-up is completed, press RED to start the scan. 5.2.3 Manual Scan In Manual Scan you can scan a single transponder, add a new transponder, edit or delete a transponder. Use the RED button to switch between satellites. Scan transponder: Use pq to select the desired transponder. Press OK to start the scan.
PART 1 • English 5.3.1.4 Auto Standby English This option allows you to set the desired Auto Standby time or to disable Auto Standby. Auto Standby will switch the receiver to standby automatically when it doesn’t receive commands from the remote control for a given period of time. Possible settings are: 1~6 Hours and Disable. The default setting for Auto Standby is 3 hours. To avoid the automatic switch off, set Auto Standby to Disable. 5.3.1.
PART 1 • English a) Download the required update file for your receiver model from our website www. strong.tv > Support b) Unzip the file, copy it to your USB device and connect it to the USB port of receiver. c) Select “Update by USB” then the update file and press OK. NEVER power off your receiver during update process and flashing data. Do not unplug the USB device during update. This may cause damage to the receiver and will void warrenty.
PART 1 • English 5.5 Multimedia The receiver can play back records you have recorded from TV and play music and show pictures from a connected USB device. You can play Gomoku or check the days in the calendar. English 5.5.1 My Album The receiver is able to show pictures in JPEG and BMP formats. Use navigation buttons and help tips to select pictures and display them. 5.5.2 My Music The receiver is able to play audio files in MP3 and WMA formats.
PART 1 • English To view technical information about the current channel, press INFO twice. In Program Information menu the receiver will display the current program information such as satellite name, program name and number, local frequency, polarity, 22K tone, DiSEqC, down frequency, symbol rate, video PID and audio PID and also the signal strength and signal quality of the current program. 6.2 Recording Information During a record press INFO to display or remove the record duration banner. 6.
PART 1 • English 6.6 TELETEXT function Press TEXT in normal viewing mode and pq to increase or decrease the displayed page number. Use numeric buttons to input a page directly. English 6.6 Subtitles function Press SUB in normal viewing mode. If the current channel broadcasts subtitle information, the Subtitle Language selection menu will appear. Use tu to select between DVB and Teletext subtitles. Use pq to select subtitle language and press OK to confirm. 6.
PART 1 • English No picture Cause The receiver can’t receive the signal Incorrect values of some tuner parameters. Wrong direction of the dish Receiver tries to start- Receiver detected short cut in your up, switches ON/ cable system or detected “Antenna Power Overload”. OFF/ON/OFF… or displays “LOAD” The remote control does not work The batteries of the remote control are not inserted or exhausted The USB storage device is not recognized. The external USB HDD does not start.