Picture similar Digital High Definition Satellite Receiver SRT 7300 CI+ User Manual Bedienungsanleitung Gebruiksaanwijzing Manuel de l'utilisateur Manuale per l'uso Használati utasítás Návod k obsluze Používateľská príručka
1 3 2 Fig. 1 1 Fig. 2 2 4 3 1 5 4 7 6 9 8 2 3 4 5 6 7 8 10 9 9 11 13 8 12 14 15 16 18 19 22 23 26 28 Fig.
SCART Fig. 4 A B C HDMI Fig. 5 A B A Fig.
PART 1 • English 26 Dec 2012 18:27 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 2 3 3 3 2.0 Your Receiver 2.1 DEFAULT PIN-CODE: 0000 2.2 Front Panel 2.3 Rear Panel 2.4 Remote Control Unit 3 3 3 4 4 3.0 Connections 3.1 Basic connection using a Scart cable 3.2 Basic connection using an HDMI cable 3.3 Connecting multiple fixed dishes using a DiSEqC 1.0 switch 3.4 Connecting and using the IR extender 5 5 5 5 5 4.
PART 1 • English 1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 1.3 Equipment Set-up English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna. Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver. The following symbols will serve as follow.
PART 1 • English 2.3 Rear Panel Fig 2. SAT IN To connect to the LNB of your satellite dish for reception of satellite broadcast signal 2. SAT OUT To loop through the satellite signal to a second receiver 3. AUDIO (L/R) To connect to the audio input of your HIFI or television 4. VIDEO (RCA) To connect to the RCA video input of your TV or VCR using an RCA cable 5. S/PDIF To connect to a digital or home cinema audio amplifier 6. TV SCART To connect to TV using a SCART cable 7.
PART 1 • English GREEN/PAUSE Freezes/resumes the current broadcast YELLOW/SUB Displays a list of available subtitling for the current channel BLUE/V.F.
PART 1 • English 4.0 Starting up for the first time Ensure that your satellite signal is of good quality and that all connections are sound. In case of difficulties or questions, please ask you local dealer for assistance. It is recommended to follow the Setup Wizard step by step. It will guide you through the basic installation and channel searching process. You can enjoy digital HD broadcasts within just a few minutes. 4.
PART 1 • English 4.2.4 Subtitles Use this option to set the preferred subtitle language or select “off” if you do not want this option. 4.3 Satellite Selection English Use pq to highlight the satellite your dish is aimed at and press OK to confirm. If your dish is aimed at Astra 1C, 1E, 1F, select ASTRA 19.2E. The SCAN MODE screen will appear. If your dish is aimed at HOT BIRD, select HOTBIRD 13E.The SCAN MODE screen will appear. If your dish is aimed at another satellite, select OTHER.
PART 1 • English 6.0 Operation In viewing mode, several features are available to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your new receiver. 6.1 Changing channels Your new receiver is equipped with three ways to change channels. via direct access via the channel list and via the P+/P- keys. 6.1.
PART 1 • English remote control allow you to jump to selected pages directly, as indicated on the bottom of the teletext screen. Press EXIT to go back to viewing mode. 6.5 Subtitles English Some channels support a choice of different DVB subtitle languages. Press SUB in viewing mode to display a list of available subtitle languages. 6.6 Changing the video format To change the video format while watching TV, simply press the V.F key in viewing mode. A list with available HDMI resolutions will pop up.
PART 1 • English Note: The Timeshift will only work correctly when a fast USB storage device such as an USB2.0 HDD is connected to the receiver. Distorted picture and / or audio during Timeshift indicate a low USB device speed. STRONG cannot guarantee for USB devices used. Especially when Timeshift is activated at channels with high data rate (High quality SD/HD), STRONG cannot guarantee an accurate Playback of the Timeshift file. 7.
PART 1 • English English Scrambled: scan scrambled channels only. Service Type All: scan TV and Radio channels TV scan: TV channels only Radio: scan radio channels only. Network Search Disabled: no network search Enabled: network search will be performed. Once all settings are made, press the GREEN button on the remote control to start the scan or EXIT to quit without scanning. All newly found channels will be stored at the end of the channel list.
PART 1 • English highlight Location and use tu to change the location. Possible settings are: East and West. Once all settings are made press GREEN to save or EXIT to quit without saving. Adding a satellite To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and press YELLOW. The procedure for adding a satellite is the same as for editing a satellite. 7.2 Setup Use the Setup menu to configure the system settings of your receiver.
to a digital surround amplifier. The digital output can be switched off by setting Digital Audio to Off. Video Format: This setting is only active when the receiver is connected to the TV set via HDMI. It allows you to set the preferred HDMI screen resolution. Available options depend from your TV set. Once all settings are made, press EXIT to leave the Output Options menu. A confirmation banner will be shown. Press OK to save your settings or EXIT to discard. 7.2.
PART 1 • English wishes. Use pq to highlight the setting you wish to change and tu or [0~9] to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. Banner Show: When set to On, the info banner displaying channel name, channel number and Now/Next information will be shown every time you change channels. To disable the banner, set this item to Off. Banner time (sec.): defines the time after which the OSD banners time out.
7.3.2 Favourite Your new receiver allows you to store channels in up to 8 favourite lists. Due to the large number of channels available on satellite nowadays, this can be a very useful function. Use TV/R to toggle between TV and radio channels. Select the channel you wish to add to a group with pq. Now select the group you wish to add the channel to with FAV. Press the FAV button multiple times to move through all available favourite groups.
PART 1 • English Listening to MP3 music Select the desired MP3 file and press OK to start playback. During playback, the following functions are available: : starts playback of the next MP3. " starts playback of the previous MP3. 3 stops playback. 5 shuffle: All files in the directory will be played back in random order. 6 repeat: Press once for single track repeat or twice to repeat all files. To exit the file explorer: Use EXIT to get back to the Root directory of your USB device.
PART 1 • English 7.4 Advanced 7.4.1 Common Interface The receiver is equipped with one slot of Common Interface which have access to the scrambled the pay per view services with various conditional access modules and a valid smart card. Depending from module you can read module information, smart card information, download new software for module and set up module language. The programs that can be descrambled are determined by the conditional access module and smart card you use. 7.4.
PART 1 • English 7.4.5 Factory Reset A factory reset will restore your receiver to the factory default settings. To reset the receiver, you have to enter your PIN code (Default PIN:0000). After the reset, the receiver will start up in the Setup Wizard. Warning: A factory reset will permanently delete all your personal settings, timers and stored channels. Please consider this before you perform a factory reset. 7.5 Games Your receiver is equipped with 4 games.
Symptom Cause The USB storage device Wrong formatted. is not working properly. The external USB Power consumption is too high. HDD does not start. Remedy Format USB device by receiver in menu Channel>File Explorer. Connect an extra power supply adapter to your USB HDD device. The receiver switches Auto Power Down function is to STBY automatically. activated and reached the adjusted time (default 3h). In the menu Setup>Time Setting you can adjust the Auto Power Down time or disable it. 9.
PART 1 • English System & Memory CPU: STi7111 Flash Memory: 8 MBytes System Memory: 256 MBytes Connectors SAT IN; SAT OUT TV SCART (RGB, CVBS, Audio L/R Output with volume control) HDMI (V/A-Output) Type A Version 1.0 HDCP 1.1 RCA Output - Audio L/R & Video Output S/PDIF Out (Coaxial, Optical) IR Extender input USB 2.0, Type A Connector CI+ compatible slot General Data Input Voltage Range: 100 - 240 V AC, 50/60 Hz Power Consumption: max. 20 W, typ. 7.
