Picture similar Digital Free-To-Air Satellite Receiver SRT 6004 /6011 User Manual
PART 1 • English 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2 2 3 3 4 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control 5 5 5 6 3.0 CONNECTIONS 3.1 Connecting to TV & VCR 3.2 Connecting to Digital Audio Amplifier 3.3 Connecting to Satellite Dish 3.4 Connecting to serial cable for downloading software 7 7 7 7 8 4.0 STARTING UP 4.1 Language Selection 4.2 Select Satellite 4.3 Antenna mode 8 8 8 8 5.0 MAIN MENU 5.
PART 1 • English 1.0 INTRODUCTION 1.
PART 1 • English Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep the packaging away from children. When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories. Failing to comply with such packaging procedures could void your warranty. 1.
PART 1 • English 1.4 Features & Accessories For all digital Free-To-Air TV and Radio programmes via satellite Set-up support for first time installation & user-friendly menu n 4.
PART 1 • English 2.1 Front Panel SRT 6004 see Fig.1 1. Mode indicator The RED light indicates that the receiver is in STAND-BY mode. The GREEN light indicates that the receiver is in AWAKE mode. 2. Power On/Off button1 3. Channel Up/Down buttons1 4 digits display1 In STAND-BY mode this indicates current time In AWAKE mode this indicates current channel number 1 Only for model SRT 6011 2.2 Rear Panel SRT 6004 see Fig.1 1.
PART 1 • English 2.
PART 1 • English English 3.0 CONNECTIONS 3.1 Connecting to TV & VCR Basic connection with a Scart cable (Fig. 3) 1. Connect the satellite signal from the LNB to the LNB IN connector. 2. Connect the TV SCART connector at the back of the receiver to the SCART IN connector on your TV set. Basic connection with a RCA cable (Fig. 4) 1. Connect the satellite signal from the LNB to the LNB IN connector. 2. Connect the Video RCA connector at the back of the receiver to the Video IN RCA connector on your TV set.
PART 1 • English Connecting a dish on a motorized positioner to your receiver (Fig. 9) Another possibility for watching programs from multiple satellites is by mounting a dish to a motorized DiSEqC 1.2 positioner. Have your dealer mount the dish to the positioner, set the correct angle of the elevation and let him set the center point for your positioner.
b) Dish mounted on DiSEqC 1.2 motor Set Antenna mode to DiSEqC 1.2, choose NEXT and press the OK button. The menu Adjust antenna will appear. Select transponder receivable at your location (choose Transponder field and select transponder by pressing LEFT/RIGHT button). Then choose field Move Dish and adjust position of the dish by pressing the LEFT/RIGHT button. Once you adjust the dish position choose Store position, set number of the position by pressing LEFT/RIGHT button.
PART 1 • English OK, the program name dialog will shown as below. Use the LEFT/RIGHT buttons to move the cursor to the character you wish to edit. Use the UP/ DOWN buttons to change character (scroll alphabet). If you wish to delete character you have to replace it with “space” character. When editing is complete, press the OK button. Move channel Press the UP/DOWN keys to point the focus of the menu to the channel of your selection.
PART 1 • English English Delete satellite If you want to delete a satellite, press the YELLOW key. Then warning message will appear. Select OK and press the OK key to confirm. 5.2.2 Auto Scan Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free then only “Free to Air” channels will be added to the channel list. If mode is Free+Scrambled then all channels from selected satellite will be added to the channel list. Press the YELLOW Key to set the Blind Scan to ON or OFF.
PART 1 • English 5.3.1 Preference 5.3.1.1 Language Setting You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. Press OK to confirm. 5.3.1.2 TV settings You can set the TV mode, Screen mode and Video output. TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm.
PART 1 • English 5.3.3.1 Channel Lock English Set the system Channel Lock to ON or OFF. If the channel lock is on, the user has to enter the parental PIN code correctly before watching the locked channel. 5.3.3.2 Menu Lock Press OK to select whether you need the lock or not for the Menu, YES or NO, press OK to confirm. If the menu lock is on, then for some operations such as search program and set factory default, you need to enter your PIN. 5.3.3.3 Parental Setting Set some channels to lock status.
PART 1 • English If your antenna is primed to Hotbird 1, 2, 3, 4 at 13E then enter following parameters: Frequency: 12476; Polarity: H (Horizontal); Symbol rate: 27500 Move menu focus to OK and press OK button on remote control. The receiver will check availability of the software update on air and load the latest software, if available. Do not switch power off and do not disconnect the receiver from the aerial during update process.
“Power Off”: The receiver powers off at the designated date and time. Cycle: You can set the cycle of the action designated in the timer mode (One time, Daily or Weekly). You can set the start date of the timer action. You can set the start time of the timer action. You can set the end time of the channel viewing when the Timer mode is on Time Interval. Select between TV and Radio.
PART 1 • English 6.0 WATCHING TV AND LISTENING TO THE RADIO 6.1 Program Information In normal operation status (no menu operation), press the INFO button. The program information banner will be displayed at the bottom of screen. From program information banner you can read channel number, channel name, current and next program name (if available from broadcast) and current time. To check technical information about channel press INFO button twice, the Program Information menu will appear on screen.
move menu focus to selection of group. Use LEFT/RIGHT buttons to select group of your choice. Select group “NO FAV” and press OK if you wish to exit from favourite channel list mode. 6.5 Selection Audio Language Press the AUDIO button on the remote control to select the audio language. Select the Audio Channel or Sound mode with UP/DOWN buttons. Select Audio channel number or Sound mode (Stereo, Left or Right channel). Press OK to confirm your selection. Your selection will be memorized for current channel.
PART 1 • English Symptom Cause Remedy Incorrect values of some tuner parameters Set the values of the tuner parameters correctly in the installation menu. Wrong direction of the dish Check the signal strength with a spectrum analyzer and adjust your dish correctly. Message “Antenna Power Overload” displayed on TV Receiver detected short cut in your cable system Disconnect receiver from main power Check your cable system. remove short cut.Replace LNB. Restart receiver.
PART 1 • English 4. A/V & Data In/Out TV Scart Output: VCR Scart Input/Output:1 CT216 32-bit RISC CPU 108 MHz 16 Mbits 64 Mbits 3 RCA Video and Audio output: S/PDIF output:1 Data Interface: Connector: RGB, CVBS, Audio L/R Output with Volume Control Input: CVBS, Audio L/R Output: CVBS, Audio L/R Output with Volume Control Yellow: Video output; White: Audio Left; Red: Audio Right Digital audio output, coaxial RS-232, Bit Rate: 115200 baud 9-Pin D-Sub Male type 5.
PART 1 • English A.3 GLOSSARY OF TERMS C band DiSEqC Fixed Dish Free-To-Air broadcast Ku band LNB MPEG Network PAL PID PIN Code Polarization RS-232 20 3.7 ~ 4.2 GHz Frequency. Digital Satellite Equipment Control. A dish antenna that is aimed at one particular satellite. Unscrambled broadcast which you can view for free 11 ~ 13 GHz Frequency. (Low-Noise Block down-converter). The LNB is an electronic unit mounted on the satellite dish.
