Users Manual

ManualsBrandsStronglink ManualsElectronicsNFC Writer Module

Table Of Contents

StrongLink SL040

http://www.stronglink-rfid.com

USB Mifare Reader

MAIN FEATURES

• USB Keyboard Emulator, Plug and Play

• Frequency: 13.56MHz

• UID read supported: Mifare Mini, Mifare 1k, Mifare 4k, Mifare Plus,

Ultralight, DesFire & Mifare_ProX

• Data read supported: Mifare Mini, Mifare 1k, Mifare 4k and Ultralight

• Integrated antenna, LED and Buzzer

• Working current less than 80mA @5.0V

• Operating distance: Up to 60mm, depending on tag

• Storage temperature: -20 ºC ~ +85 ºC

• Operating temperature: -10 ºC ~ +70 ºC

• Dimension: 65mm × 46mm × 7 mm

SETTING MODE

Switching SW1-1 to OFF position and repower, SL040 goto setting mode.

Run SL040Config.exe, RED-LED on SL040 will glitter.

Summary of content (9 pages)

PAGE 1
StrongLink SL040 USB Mifare Reader MAIN FEATURES • USB Keyboard Emulator, Plug and Play • Frequency: 13.56MHz • UID read supported: Mifare Mini, Mifare 1k, Mifare 4k, Mifare Plus, Ultralight, DesFire & Mifare_ProX • Data read supported: Mifare Mini, Mifare 1k, Mifare 4k and Ultralight • Integrated antenna, LED and Buzzer • Working current less than 80mA @5.
PAGE 2
StrongLink SL040 • Read Unique Number ♦ LSB First or HSB First ♦ HEX or Decimalist e.g. data stored in block0 of Mifare 1k as below sheet BLOCK 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 01 02 03 04 04 88 04 00 47 C1 25 A8 45 00 31 06 If [LSB] and [HEX] selected, SL040 output 01020304 If [MSB] and [Decimalist] selected, SL040 output 0067305985 Remark: SL040 will append 0 in the front to keep all the output 10 digits number unified in DEC. http://www.stronglink-rfid.
PAGE 3
StrongLink SL040 • Read Data SL040 not only output the UID, can also read data from Ultalight, Mifare Mini, Mifare 1k and Mifare 4k. Remark: All blocks which to be read should be have same key. WORKING MODE Switching SW1-1 to ON position and repower, SL040 run working mode. RED-LED on SL040 will light. According to the config information stored in memory, SL040 will automatically read the unique serial number and data, then output to PC when Mifare tag in its detective range.
PAGE 4
FCC Statement 15.19 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 15.21 Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
PAGE 5
ORIGINAL EQUIPMENT MANUFACTURER (OEM) NOTES  The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and 15.109) before declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.  The OEM must comply with the FCC labeling requirements.
PAGE 6
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
PAGE 7
2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
PAGE 8
2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
PAGE 9
2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.