000-Lb. Rapid Lift Hydraulic Table Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This hydraulic table designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use This Strongway 1000-Lb. Rapid Lift Hydraulic Table is a scissor-lift table with an easy foot-pedal operation. It’s ideal for lifting, positioning, and transporting heavy materials around the shop, factory, warehouse, or office. Technical Specifications Property Load Capacity Raised Height Specification 1000 lb.
liquids, gases, or dust. Do not allow the product to come into contact with an electrical source. The tool is not insulated and contact will cause electrical shock. Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area.
the tool itself. Keep guards in place and in working order. Never operate the product without the guards in place. Do not leave the tool running unattended. Specific Operation Warnings ⚠WARNING To prevent serious injury or property damage, read and understand owner’s manual before use. Do not exceed the rated load capacity. Be aware of dynamic loading. Sudden load movement may briefly create excess load causing product failure.
Reference 5 Subassembly Pump Assembly Instructions ⚠WARNING Use at least two people to lift out of the box. This table arrives mostly assembled but some assembly is required: 1. Unfold the handle by pulling it up and back into a vertical position. Lock the handle into position. Note: The handle may be released and folded back down by pressing down on the locking bar. 2. Install the foot pedal. Insert the pump lever (33) with foot pedal (34) into the connecting rod and secure with a bolt.
Before Each Use ⚠WARNING Inspect the general condition of the table. Do not use lift table if damaged. Replace damaged parts before resuming operation. Test the cart operation by using the foot pedal and control lever. Make sure the table raises and lowers properly before adding weight to the table. Before raising the table top, lock the casters. Operating Instructions ⚠WARNING Do not exceed the rated load capacity. Be aware of dynamic loading.
Lower the Table The control lever controls the operation of the hydraulic pump unit. To lower the pump and table, squeeze the control lever. When the control lever is released, the pump and table movement will stop and the table will remain stationary. Make sure the bars lock in place and squeeze the control level. After Each Use ⚠WARNING To prevent accidents when finished using the cart, move the cart to a safe location and lock the locking swivel casters.
Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule. Maintenance Interval Maintenance Point Inspect the general condition of the table.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 Part Description Handle Roll Pin Control Lever Hex Nut M8 Bolt Jacket Pull Rod Cotter Pin Washer Pin Page 11 of 17 Quantity 1 1 1 15 1 1 1 6 17 4
Reference 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Part Description Spring Retaining Ring Pin Draw Springs Screw Release Valve Link Bolt Cotter Pin Pin Power Unit Pin Pin Retaining Ring Busher Spring Spring Cap Linkage Busher Connecting Rod Rubber Pad Pin Bolt Pump Lever Foot Pedal Grip Seat Handle Lock Pivot Spring Handle Lock Bar Washer Spring Washer Locking Swivel Caster Base Lock Nut Washer Bearing Wheel
Parts Diagram-Pump Parts List-Pump Reference 1 2 3 4 5 6 Part Description Dust Ring O-Ring Top Nut Sealing Gasket Oil Plug Oil Tank Page 13 of 17 Quantity 1 1 1 1 1 1
Reference 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Part Description T-Ring Cylinder Copper Washer Ram O-Ring Piston O-Ring Retainer O-Ring Washer Retaining Ring Ram Treaded Sleeve O-Ring Sealing Gasket O-Ring Washer Bolt Steel Ball Spring Steel Ball Steel Ball Adjusting Bolt O-Ring Spring Ball Seat Steel Ball Sleeve Pumping Valve Seat O-Ring Sealing Gasket O-Ring O-Ring Release Valve Spring Steel Ba
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China.