AIR BUMPER JACK OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification.
IMPORTANT SAFETY CONSIDERATIONS JACK USE AND CARE Do not modify the Jack in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the Jack was designed. Always check of damaged or worn out parts before using the Jack. Broken parts will affect the Jack operation. Replace or repair damaged or worn parts immediately. Store idle Jack.
SAFETY MARKINGS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. WARNING: Study, understand, and follow all instructions before operating this device. Do not exceed rated capacity. Use only on hard, level surfaces. Load saddles equally. Lifting device only. Immediately after lifting, support the vehicle with appropriate means. Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
* Position the Jack Position the jack to only lift on the areas of the vehicle as specified by the vehicle manufacturer. * Always Use Jack Stands After lifting the vehicle always support the load with appropriately rated vehicle Jacks stands before working on the vehicle. * Do Not Overload Jack Do not overload this jack beyond its rated capacity. Overloading this jack beyond its rated capacity can cause damage to or failure of the jack.
ASSEMBLY 1. Familiaraize yourself with the jack. BEFORE USE 1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use. 2. Check and that the pump operates smoothly before putting into service. 3. This product is fitting use standard 1/4" NPT air fitting. If changing the fitting is required, install a 1/4" NPT fitting of your choice; ensure that thread tape or compound is used to seal connection. 4.
OPERATION RAISING THE JACK Block the vehicle’s wheels for lifting stability. Secure the load to prevent inadvertent shifting and movement Position the jack near desired lift point. Set the Parking Brake in the vehicle. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Position the jack so that the saddle is centered and will contact the load lifting point firmly. 5.
MAINTENANCE INSTRUCTIONS If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance.
TROUBLESHOOTING JACK WILL NOT LIFT LOAD JACK WILL NOT HOLD LOAD JACK WILL NOT LOWER POOR JACK LIFTING WILL NOT LIFT TO FULL EXTENSION CAUSES AND SOLUTIONS Release valve is not completely closed (Turn handle clockwise). Air Supply Inadequate 9 Weight Capacity Exceeded. Air is in the hydraulics. Purge air from system. Lubricate moving parts.
ASSEMBLY DIAGRAM 10
PARTS LIST Index # Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Base Frame Snap Ring Wheel Washer Saddle Extension Saddle Bolt M14X100 Flat Washer Φ14 Nut M14 Swivel Caster Bolt M8X20 Lock Washer Φ8 Bolt M6X90 Flat Washer Φ6 Nut M6 Air Cylinder Air Control Valve Protective Cover Bolt M12X35 Y-Ring Bolt M14X115 Lub Plug Seal Assembly Nut M8 Rubber Saddle Pad Bolt M8X30 Wheel Part No.
Limited Warranty Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.