3 TON FLAT BASE LONG RAM JACK OWNER’S MANUAL WARNING: Read carefully and understand all OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification.
SAVE THESE INSTRUCTIONS IMPORTANT SAFETY CONSIDERATIONS DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL. To maintain the Service Jack and user safety, the responsibility of the owner is to read and follow these instructions. Inspect the service jack for proper operation and function. Keep instructions readily available for equipment operators. Make certain all equipment operators are properly trained; understand how to safely and correctly operate the unit.
SAFETY MARKINGS WARNING: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Study, understand, and follow all instructions before operating this device. Do not exceed rated capacity. Use only on hard, level surfaces. Lifting device only. Immediately after lifting, support the vehicle with appropriate means. Lift only on areas of the vehicle as specified by the vehicle manufacturer. No alterations shall be made to this product. Only attachments and/or adapters supplied by the manufacturer shall be used.
*Do not raise or lower the vehicle unless tools, materials and people are clear. When the lift is being lowered, make sure everyone is standing at least six feet away. Be sure there are no tools or equipment left under or around the jack before lowering. * Always lower the jack slowly. * DO NOT USE THE JACK TO SUPPORT OR STABILIZE A LOAD. Using the jack to support or stabilize a load may result in unexpected movement and result in serious injury, being crushed and death.
ASSEMBLY 1. Familiarize yourself with the jack. 2. Use handle (21) to Turn release valve (28) counterclockwise on full turn to the open position.
3. Line up the handle to the handle socket located on the side of the jack, then insert the handle inside the handle socket. 4. Secure the handle in place inside the handle socket. Without any weight on the jack, cycle the lift up and down several times to insure the hydraulic system is operating properly. (Perform to the Air Purge Procedure before first use.
2. Rapidly pump the handle 6-8 times. Leave handle in down position to expose oil fill plug. 3. Purge air trap in the system by opening the attached oil vent, do not remove oil vent. Oil vent Is to stay open at all times when in use. (Oil vent is closed during shipping) For units with rubber oil plugs: {With a flat blade screwdriver, push the oil fill plug slightly to the side to purge trapped air from system. (Use caution not to tear or puncture the oil plug.)} 4.
BEFORE USE 1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use. 2. Perform the air purge procedure. (See previous instructions for system purge procedure.) 3. Check and that the pump operates smoothly before putting into service. 4. Inspect before each use. Do not use if bent, broken or cracked components are noted. OPERATION RAISING THE JACK 1. Position the jack near desired lift point. 2.
WARNING: STOP PUMPING WHEN THE RAM RISES TO THE RED STOP MARK ON THE RAM. THIS WILL PREVENT THE JACK FROM POSSIBLE MALFUNCTION AND IMPROPER USE. CAUTION: NEVER WIRE, CLAMP OR OTHERWISE DISABLE THE LIFT CONTROL VALVE TO FUCTION BY ANY MEANS OTHER THAN BY USING THE OPERATOR'S HAND. USE THE HANDLE PROVIDED WITH THIS PRODUCT OR AN AUTHORIZED REPLACEMENT HANDLE TO ENSURE PROPER RELEASE VALVE OPERATION. DO NOT USE EXTENSIONS ON THE OPERATING HANDLE. LOWERING THE JACK 1. Grasp the handle firmly with both hands.
MAINTENANCE INSTRUCTIONS If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance.
TO ADD JACK OIL: 1. Position the jack on level as shown and lower the ram. 2. Remove the oil plug. 3. Fill the oil case until oil level is just beneath the lower rim of the oil fill hole.
4. Replace oil plug. 5. Perform the Air Purge Procedure. TO REPLACE JACK OIL: 1. Position the jack on level as shown and lower the ram. 2. Open release valve by turning handle counter-clockwise (4 full turns).
3. Remove the oil fill plug. 4. Turn the jack on its side so that old oil will drain from the oil fill hole. 5. Position the jack on level ground and with the ram in the lowered position. 6. Fill the oil case until oil level is just beneath the lower rim. KEEP DIRT AND OTHER MATERIAL CLEAR WHEN POURING.
7. Replace oil plug. 8. Perform the Air Purge Procedure. ADDITIONAL WARNINGS DO NOT USE MOTOR OIL IN THE JACK. ONLY USE ANTI-FOAMING JACK OIL. ALWAYS USE A GOOD GRADE HYDRAULIC JACK OIL. DO NOT USE HYDRAULIC BRAKE FLUID, ALCOHOL, GLYCERINE, DETERGENT, MOTOR OIL OR DIRTY OIL. USE OF A NON-RECOMMENDED FLUID CANCAUSE DAMAGE TO A JACK. AVOID MIXING DIFFERENT TYPES OF FLUID AND NEVER USE BRAKE FLUID, TURBINE OIL, TRANSMISSION FLUID, MOTOR OIL OR GLYCERIN.
TROUBLESHOOTING JACK WILL NOT LIFT LOAD JACK WILL NOT HOLD LOAD JACK WILL NOT LOWER POOR JACK LIFTING WILL NOT LIFT TO FULL EXTENSION 16 CAUSES AND SOLUTIONS Release valve is not completely closed (Turn handle clockwise). Weight Capacity Exceeded. Air is in the hydraulics. Purge air from system. Low oil level. Add oil as required. Oil reservoir is overfilled: Drain excessive oil. Lubricate moving parts.
ASSEMBLY DIAGRAM 17
PARTS LIST Index # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Description Top Nut O-Ring Sealing Gasket Oil Tank Oil Plug Seal Ring Ram Bowl Washer O-Ring Cylinder Copper Washer Ball Valve Block Ring Handle Socket Pin Plunger Back Up Ring O-Ring Pump Cylinder Copper Washer Ball Handle Ball Sealing Gasket Release Spindle Part No.
Limited Warranty Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
