50 TON AIR/HYDRAULIC BOTTLE JACK OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification.
IMPORTANT SAFETY CONSIDERATIONS JACK USE AND CARE Do not modify the Jack in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the Jack was designed. Always check of damaged or worn out parts before using the Jack. Broken parts will affect the Jack operation. Replace or repair damaged or worn parts immediately. Store idle Jack.
SAFETY MARKINGS WARNING: 1. Study, understand, and follow all instructions before operating this device. 2. Do not exceed rated capacity. 3. Use only on hard, level surfaces. 4. Lifting device only. Immediately after lifting, support the vehicle with appropriate means. 5. Do not move or dolly the vehicle while on the jack. 6. Lift only on areas of the vehicle as specified by the vehicle manufacturer. 7. No alterations shall be made to this product. 8.
GENERAL SAFETY INSTRUCTIONS * Position the Jack Position the jack to only lift on the areas of the vehicle as specified by the vehicle manufacturer. * Always Use Jack Stands After lifting the vehicle always support the load with appropriately rated vehicle Jacks stands before working on the vehicle. * Do Not Overload Jack Do not overload this jack beyond its rated capacity. Overloading this jack beyond its rated capacity can cause damage to or failure of the jack.
ASSEMBLY 1. Familiarize yourself with the jack. 2. Attach the 2 handle pieces making sure to align the holes on both sections. 3. Line up the handle to the handle socket located on the side of the jack, then insert the handle inside the handle socket. Insert Handle Here 4. Secure the handle in place inside the handle socket. Without any vehicle on the jack. Cycle the lift up and down several times to insure the hydraulic system is operating properly. (Perform to the Air Purge Procedure before first use.
SYSTEM AIR PURGE PROCEDURE IMPORTANT: BEFORE FIRST USE Perform the following Air Purge Procedure to remove any air that may have been introduced into the hydraulic system as a result of product shipment and handling. This step is to be completed without any weight on the jack. 1. Turn release valve counterclockwise on full turn to the open position. 2. Rapidly pump the handle 6-8 times. Leave handle in down position to expose oil fill plug. 3.
BEFORE USE 1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use. 2. Perform the air purge procedure. (See previous instructions for system purge procedure.) 3. Pour a teaspoon of good quality, air tool lubricant into the air supply inlet of the lift control valve. (See illustration) Connect to air supply and operate for 3 seconds to evenly distribute lubricant. 4.
6. Close the release valve by turning it clockwise until it is firmly closed. 7. Before raising the vehicle double check and verify the saddle is centered and also has full contact with the lifting point. 8. Pump handle or squeeze air trigger to lift until saddle contacts load. (To stop air operation, simply release the grip on the lift control valve.) Continue to pump the jack handle to lift the vehicle to the desired height.
MAINTENANCE INSTRUCTION If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance.
TO ADD JACK OIL: 1. Position the jack on level ground and lower the saddle. 2. Remove the oil plug. 3. Fill the oil case until oil level is just beneath the lower rim of the oil fill hole.
4. Replace oil plug. 5. Perform the Air Purge Procedure. TO REPLACE JACK OIL: 1. Position the jack on level ground and lower the saddle. 2. Open release valve by turning handle counter-clockwise (4 full turns).
3. Remove the oil fill plug. 4. Turn the jack on its side so that old oil will drain from the oil fill hole. 5. Position the jack on level ground and lower the saddle.
6. Fill the oil case until oil level is just beneath the lower rim. KEEP DIRT AND OTHER MATERIAL CLEAR WHEN POURING. 6. Replace oil plug. 7. Perform the Air Purge Procedure. ADDITIONAL WARNINGS: DO NOT USE MOTOR OIL IN THE JACK. ONLY USE ANTI-FOAMING JACK OIL. ALWAYS USE A GOOD GRADE HYDRAULIC JACK OIL. DO NOT USE HYDRAULIC BRAKE FLUID, ALCOHOL, GLYCERINE, DETERGENT, MOTOR OIL OR DIRTY OIL. USE OF A NON-RECOMMENDED FLUID CANCAUSE DAMAGE TO A JACK.
ASSEMBLY DIAGRAM 15
PARTS LIST Index # 1.1 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 1.15 1.
Index # 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Description Ram Header Ram Knob Spring Plate Screw Nut Connector 1 Release Valve Rod 2 Connector 2 Handle Cap Upper Handle Connector 2 Lower Handle Bole Washer Caster Shaft Part No. TQ12002-06 Qty.
Limited Warranty Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.