2000-Lb. Capacity Mini Pallet Jack Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This pallet jack is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Strongway 2000 Lb. Capacity Mini Pallet Jack is designed for transportation of loads with a level, attached base and to be used only on a firm and even surface, such as concrete or asphalt. The load must be on evenly distributed pallets, with the ideal loading mode such that the center of gravity of the load is at the central position of the fork.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not allow the product to come into contact with an electrical source. The tool is not insulated and contact will cause electrical shock.
Be sure the load is secure and stable before moving. Do not operate a loaded pallet jack on ramps or inclines. Keep the load centered on the pallet jack. Wear steel toed boots while operating the pallet jack. Check for damaged parts before operating. Do not operate a damaged or faulty pallet jack. Do not attempt repairs unless you are trained or authorized to do so. Operate a pallet jack from a designated operating position.
1. Place the base of the HANDLE TUBE (Fig. 1) on the PRESSURE FRAME (Fig. 1). Align the holes (Fig. 1) at the base of the HANDLE with the holes in the PRESSURE FRAME. The chain should drop through the middle hole of SHAFT (Fig. 2). Fig. 1 2. Using a screwdriver, pry the LEVER PLATE (Fig. 2) up and slip the bolt head under the notch in the LEVER PLATE. Fig.
3. Secure the HANDLE to the pallet jack with the three SPRING WASHERS and SCREWS (Fig. 1). It is a good idea to remove any air bubbles that might have accumulated in the hydraulic system during shipping. Operating Instructions ⚠WARNING To avoid serious bodily injury or death, and/or property damage, do not exceed the rated load capacity. When not in use, do not allow heavy loads to remain on the fork for an extended period of time. Always lower the fork completely when not in use.
Adjusting the Control Handle- 3 Positions On the Handle Tube (1) of this pallet jack, you can find the Control Lever (5), which can be placed in three positions (See Fig. 3): LOWER - To lower the load, pull up on the control lever. NEUTRAL - Place the control lever in this position while pulling the pallet jack or load. LIFT - To raise the load, push down on the control lever and pump the handle to raise the load. Lower Neutral Lift Fig.
Maintenance Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule.
Maintenance Interval Maintenance Point SEAL AND O-RING REPLACEMENT FOR RAM AND PLUNGER PISTON Raise the pallet jack by pumping the handle. Remove the shaft (18). This will free the pump and handle assembly from the pallet jack. Remove the oil plug (46), turn pump over and empty the oil into a suitable container. Pump the handle until all the oil has drained. Dispose of used hydraulic oil according to local disposal regulations. Pull out the plunger piston (40) and/or ram piston (42).
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part Description Handle Handle Cap Lever Spring Pin Bolt Oil Lite Bushing Spring Pin Oil Lite Bushing Roller Roller Pin Release Rod Parts Plunger Piston Spring Cap Spring Dust Seal Page 12 of 16 Qty.
Reference 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Part Number 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Part Description U-Packing Release Plug Washer Spring Spring Steel Ball Valve Housing Steel Ball Release Plug O-Ring Release Screw Spring Valve Steel Ball Handle Pi
Reference 70 71 72 73 74 75 76 77 78 Part Number 70 71 72 73 74 75 76 77 78 Part Description Spring Pin Rod Pin Spring Pin Arm Pin Snap Ring Load Wheel Axle Load Wheel Bearing Load Wheel Arm Qty. 2 2 2 2 4 2 4 2 2 Remark Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
