Exhaust Fan with Shutter Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fan is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use Strongway’s Exhaust Fan with Shutter is designed for exhaust and circulation of indoor air to the outdoors. Technical Specifications Item# Size Voltage Speeds Watts / Amps CFM / RPM 52852 14″ 120 1 230 Watt / 1.9 Amp 1400/1380 52853 18″ 120 1 330 Watt / 3 Amp 2800/1050 52854 30″ 120 1 570 Watt / 5.
⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the fan in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the fan where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
Disconnect the power from the fan and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the fan. Such preventive safety measures reduce the risk of starting the fan accidentally. Surges in electrical power or excessive heat may cause the fan to turn off. Wait approximately 15 minutes for the fan to resume operation. Store the fan when it is not in use. Store it in a dry, secure place out of the reach of children.
Installation ⚠WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. b) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Installation must be performed in accordance with the requirement of NEC and CEC by authorized personnel only.
hole 52854 30″ 37.6″ 37.6″ 33.9″ square hole 12.1″ 3.7″ 32.3″ 1. Use screws, nuts, and flat referrals to assemble the fan head to the shutter assembly and then firmly fasten the nuts and flat referrals to lock into place. Important: Use appropriate screws for framework and wall conditions. 2. To mount the shutter assembly, use the eight pre-punched 1/4" x 1/2" slotted mounting holes of the shutter assembly to attach the unit to the framework. 3.
Note: Be sure when the fan is mounted that the shutter louvers open upward and close downward. #52852, #52853, #52854 Wiring Diagram Before Each Use ⚠WARNING Be sure that both front and rear guard screws are completely tightened in locking position before operation. Operating Instructions This unit is not equipped with a speed selector. An external method of control will need to be wired. Refer to that specific control unit’s installation instructions. Maintenance 1.
2. Use a soft damp cloth and wipe with a dry cloth. 3. The motor bearings are lubricated at the factory and should not require any additional lubrication. However, if bearing lubrication is needed, apply a small amount of a high temperature bearing grease. 4. Use a mild detergent to clean the blades and guards. Avoid allowing the cleanser to come in contact with the motor bearings or windings. 5. Allow the fan to completely dry before the next use. ⚠WARNING Disconnect power before servicing.
7 Screw 1 8 Motor 1 9 Capacitor box 1 10 Wind cabinet 1 #52854 Parts Diagram #52854 Parts List Part# Description Qty. Part# Description Qty.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following will be required: Model Number, Serial Number/Lot Date Code, Description, and Reference Number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.