Electric Chainsaw Sharpener Bench or Wall Mount Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This sharpener is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Strongway Electric Chainsaw Sharpener with Bench or Wall Mount is designed for sharpening most chainsaws. Technical Specifications Property Supply voltage Chain Pitch Motor input power Maximum speed Weight Specification 110 Volt / 60Hz ¼ Inch to ¾ Inch 2.1 Amps (230 W) 3400 RPM 20 lb. Important Safety Information ⚠WARNING Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage.
and contact will cause electrical shock. Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. ⚠WARNING PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool may result in serious personal injury. Dress properly.
another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself. Keep guards in place and in working order. Never operate the product without the guards in place. Do not leave the tool running unattended. Specific Operation Warnings ⚠WARNING Wear the proper protective equipment including ANSI Z87.1 compliant eye protection, NIOSH compliant breathing protection, and hearing protection.
Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool.
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. The smaller the wire gauge number, the greater the capacity of the cord. For example, a 14gauge cord can carry a higher current than a 16-gauge cord.
1. When installing on a bench, place the sharpener on the edge of the bench to the stop (Fig. 1) and screw it to the desk using the holes in the base. 2. When mounting on the wall, use the respective holes in the vertical part of the base. 3. After the bench top installation, fit the arm in the base, inserting the pilot pin and securing it with a hexagonal screw (Fig.2). 4. Now, fit a washer (included) on the rear side screw and screw on the setting wheel (Fig.3). 5.
7. To be able to install the disc, it is necessary to unscrew the auxiliary flange (Fig.6). Before Each Use ⚠WARNING Inspect the whole condition of the sharpener for good working condition. Check the disc you are about to use for damages prior to installation. Operating Instructions ⚠WARNING Wear the proper protective equipment including ANSI Z87.1 compliant eye protection, NIOSH compliant breathing protection, and hearing protection.
When using the sharpener outdoors, always use an outdoor rated extension cord with a splashproof plug and socket. Do not use a caustic solution to clean plastic parts. Do not use the sharpener in the proximity of flammable liquids and vapors. Not for use by or around children. Grinding Disk Replacement 1. After you have removed the ancillary flange, you can insert the grinding disc in the body from below. See that the ancillary flange and the disc butt against each other (Fig.7). 2.
2. Some types of chains require that the clamping screw be tilted by 5°-10°. 3. Now, the sharpener may be switched on and the chain grinding may be started by gently pressing the disc on the chain. Adjust the pressure as necessary. Mark the start of grinding with a piece of chalk and grind all the teeth in one direction, then turn the clamping screw (mind the angle) and grind the teeth in the opposite direction. 4. With worm chains, the lateral guide position (Fig.
Maintenance Interval Before Use Maintenance Point Inspect the sharpener for good working condition. Store it in a dry and clean place. After Use Wipe external surfaces of the sharpener with a clean cloth. Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure Possible Cause Cord not connected. Sharpener will not start.
Parts Diagram Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part Description Handle Hex Nut M6 Motor Holder Switch Adjusting Bolt 8 Adjusting Screw 8 Rubber Mat 8 Big Tensional Spring Shaft Sleeve Shaft Stand Base Flat Washer 11*28*25 Tightening Knob Fixed Disc Flat Washer 5*1 Page 14 of 17 Quantity 1 1 1 1 1 1 1 1 2 1 1 2 2 1 2
Reference 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Part Description Small Pressure Spring A Inner Hex Cylindrical Screw M5*22 Hex Nut M8 Hex Nut M6 Positioning Plate Small Pressure Spring B Stud M6*65 Rubber Mat 6 Adjusting Nut 6 Adjusting Bolt 6 Guide Wheel B Hex Nut M6 Fixed Stand B Guide Cover Small Tensional Spring Locating Rod Inner Hex Cylindrical Screw M8*35 Connecting Axis Bolt M10*65 Cam Flat Washer 5*15*1 Bolt M5
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China.