30 InchMisting Wall-Mount Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway®product! For future reference, please complete the owner’s record below: Serial Number/LotDate Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fanis designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 5 Important Safety Information .................
Intended Use The Strongway 30 Inch Misting Wall-Mount Fan is ideal for home, greenhouses, gardens, and other areas that can benefit from a misting fan.
Technical Specifications Property Motor Maximum Current Consumption Diameter Airflow Specification 120Volt AC / Direct Drive 2.0 Amps 24” 7200 CFM Important Safety Information ⚠WARNING • Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage. • The warnings, cautions, and instructions in this manual cannot cover all possible conditions or situations that could occur. Exercise common sense and caution when using this tool.
and/or property damage if contacted. ⚠WARNING PERSONAL SAFETY • Stay alert, watch what you are doing, and use common sense when operating the tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool may result in serious personal injury. • Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts.
Specific Operation Warnings ⚠WARNING • To prevent serious injury or property damage, read and understand owner’s manual before operating. • Electric shock hazard. Do not expose the unit or the plug to water or rain. Do not use the fan near a water source such as a swimming pool, bathtub, or shower. • Be sure the fan is properly grounded. • Do not use this fan with any solid-state speed control device. • Only plug the unit into a power outlet with the same voltage as rated voltage of it.
grounding instructions, or if you are not sure the tool is properly grounded. Grounded Tools: Tools with 3-Prong Plugs Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.
• If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. • If you are using an extension cord outdoors, make sure it is marked with the suffix W-A (W in Canada) to indicate it is acceptable for outdoor use. • Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
Note: Use the mounting accessories provided for mounting.
2.
Remove four sets of hexagonal nuts, spring washers, and big washers from the motor. Save them for step 2. 3. Attach the rear guard (4) to the screws found on the motor and then secure them together using four bowl washers (1), four spring washers (2), and four nuts (3) from step 2.
4. Assemble fan blade(2) onto the motor shaft by tightening two screws(1)which are located on the fan blades. Make sure the screws are tightly secured. 5. Assemble the front guard (1) to the rear guard (2) by attaching both guards together with clips.
6. Secure the assembly on the front guard and rear guard by tightening the screw(1) and nut (2) on the bottom position of each. 7. Hang the fan head on the bracket and fasten it with a screw, a connecting plate, a washer, a spring washer, and a nut.Fasten the screw that holds the vertical fan head on the bracket. Attach the knob for adjusting the tilt angle of the fan head.
8. Loosen the washer nut(1) and adjust until the fan head is at the desired angle. Tighten the washer nut. 9. Insert the screw (1) through the upper bracket.Connect the lower bracket to the upper bracket with a screw(1).Fasten the two bracketswith a spring washer (2) and hexagon nut(3).
10. Connect the misting switch (1) to the water pipe (2) and tighten it. Turn the switch (open) to open the misting function. Turn the switch (close) to close the misting function.
Before Each Use Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord. Operating Instructions ⚠WARNING • Electric shock hazard. Do not expose the unit or the plug to water or rain. Do not use the fan near a water source such as a swimming pool, bathtub, or shower. • Be sure the fan is properly grounded. • Do not use this fan with any solid-state speed control device. • Only plug the unit into a power outlet with the same voltage as rated voltage of it.
Misting Nozzle Maintenance If the misting nozzles become clogged, remove them from grill and washthem by water. Use a nonmetallic brush to scrub them if necessary, if theobstacle still exists, use the replacement nozzle or contact the customerservice for assistance.
Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Symptom Possible Cause(s) Fan may not be plugged in. There may be some obstructions in the fan. Check for any obstruction. Ifyou find an obstruction, turnthe fan“OFF”. Unplug the fanand carefully remove theobstruction. Plug the fan in andturn it on again, referring to the OPERATIONINSTRUCTIONS.
Reference 8 Part Description Wall Bracket Quantity 1 Replacement Parts • For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. • Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one yearfrom date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
