800 Amp Heavy-Duty Jumpstarter PackPackPackINSERT PRODUCT NAME Owner’s Manual HERE WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This jumpstarter is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Specifications ........................................................................................................................................ 4 Important Safety Information ............................................................................................................... 5 Specific Operation Warnings ...............
Intended Use The Strongway 800 Amp Heavy-Duty Jumpstarter is easy to use and designed for years of reliable service. It can run many DC appliances whenever you need power for work or play, at home or on the road. The 800A jumpstarter has a battery inside and is designed for jumpstarting SUVs, trucks, and vans.
Important Safety Information ⚠WARNING Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage. The warnings, cautions, and instructions in this manual cannot cover all possible conditions or situations that could occur. Exercise common sense and caution when using this jumpstarter. Always be aware of the environment and ensure that the jumpstarter is used in a safe and responsible manner.
Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Air vents on the jumpstarter often cover moving parts and should be avoided. Wear the proper personal protective equipment when necessary. Use ANSI Z87.1 compliant safety goggles (not safety glasses) with side shields, or when needed, a face shield. Use a dust mask in dusty work conditions.
pressure than the jumpstarter itself. Do not leave the jump starter running unattended. Specific Operation Warnings ⚠WARNING Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury and/or property damage. Use the unit for charging/boosting a lead-acid battery only. An incorrect connection may cause sparking. Ensure that you have the proper polarity before jump starting.
Main Parts of Product Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Subassembly Battery capacity indicators Battery capacity check button Charging indicator Reverse Polarity indicator (RED) Correct Connection indicator (Green) Buzzer of Reverse Polarity LED Work light USB/Work light on/off Switch Manual Switch USB on indicator 2.1A USB Port Receptacle of booster Cable DC Outlets Charging Port Before Each Use ⚠WARNING Charge unit fully prior to each use.
when touched. Keep plenty of fresh water, soap and a supply of baking soda on hand in the area of the batteries in case of contact with battery acid. Baking soda neutralizes lead acid battery electrolyte. The product is supplied with a rechargeable, sealed lead acid battery. This battery is selfcontained and not consumer replaceable. Batteries must be disposed of properly when they no longer hold a charge. Operating Instructions ⚠WARNING SPARK AND EXPLOSION HAZARD Risk of explosive gases.
EQUIPMENT DAMAGE Never connect the USB power port directly to a computer USB outlet. Doing so may cause damage to both the power port and USB outlet. Operation of LED Light 1. Slide the USB/LED slide switch to the right. 2. Slide USB/LED switch to middle to turn off the LED light after use. Failure to do so may damage the internal battery because of over discharge. Jump Starting an Engine 1. Make sure your vehicle is a negative ground system.
10. Disconnect the clamps from the battery of the vehicle if the connections are reversed, buzzer is sounding and the reverse polarity indicator is on, and repeat the steps 8 and 9, or proceed to step 10. 11. Turn ON the boosting power switch of the jumpstarter. 12. Crank the engine for 1–3 seconds or until it starts, whichever is first. 13. Turn OFF the ON/OFF switch after using the jumpstarter. 14.
Recharging the Battery ⚠WARNING Always ensure that internal battery is fully charged. Do not overcharge the battery. Leaving a battery in a discharged state or without recharging every 90 days may result in permanent damage to the battery and poor boosting performance. Do not use the AC or DC outlets while the power pack is being charged. Doing so may damage the charging adapter. Do not attempt to recharge the internal battery if it is frozen.
Failure Possible Cause The jumpstarter does not jump start vehicle The charging status LED indicator does not glow The charging status LED indicator flashes red and the battery has not been charged to steady after 72 hours of charging The run time for appliance is less than expected False LED reading Switches are in the “ON” position or a DC load is connected.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
