2-TON HIGH POSITION HOIST STAND OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification.
SAVE THESE INSTRUCTIONS IMPORTANT SAFETY CONSIDERATIONS JACK STAND USE AND CARE Do not modify the jack stand in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the jack stand was designed. Always check of damaged or worn out parts before using the jack stand Broken parts will affect the jack stand operation. Replace or repair damaged or worn parts immediately.
* Position the Jack Stand Position the jack stand to only support on the areas of the vehicle as specified by the vehicle manufacturer. * Always Support Load After lifting the vehicle always support the load with appropriately before working on the vehicle. * Do Not Overload Do not overload this equipment beyond its rated capacity. Overloading this equipment beyond its rated capacity can cause damage to or failure.
Assembly Use the exploded drawing as your guide to assembly. Lay all parts and assemblies out in front of you before beginning. The following procedure is recommended: All numbers in parenthesis () refer to the index number from the parts breakdown. 1. To mount the Rubber Pad (1) with the Saddle (2), use Screw M6X10 (3). 2. Attach (7) connector plate with component hardware: (8) L-Bracket (Middle Bridge) (7), using Bolt M10X20 (4), Washer 10 (5), Nut M10 (6). 3.
4. Attach the Pull Rod (11) with the Support Pillar (10), using the Plain Washer M8 (13) and Bolt M8X16 (12). 5. Attach the Short Pull Rod (14) with the Support Pillar (10), using the Plain Washer M8 (13) and Bolt M8X16 (12).
. Mount the Middle Bridge (8) with the Support Pillar (10)1using the Plain Washer M8 (13) I Bolt M8X20 (15) and Nut M8 (16). 8. To mount the Lock Plate (9) with the Support Pillar (10) using the Plain Washer M10 (59) 1 Bolt M10X25 (4) and Nut M10 (6).
9. Attach Pillar (20) with (17) handle. Install bearing assembly: first install Bearing Base (18). After bearing have been installed and handle has been attached, install (17, 19) Threaded Rodd assembly by slowly lowering (19) inside (20). 10. To adjusting the position of the jack stand, use the Lock Bolt (21), plain washer M12 (22) and (23) Hitch Pin Clip.
11. Use caution when installing and lowering threaded rod column assembly. Attach saddle bracket assembly using Bolt M10X20 (15) 12. 13. Check that all hardware is secure and tight. Jack Stand is now ready for use.
OPERATING INSTRUCTIONS RAISING THE JACK STAND 1. Adjust height by rotating the handle CLOCKWISE. 2. Check to ensure ratchet is secure before loading/un/loading. 3. Carefully position stand so that load is centered on stand’s saddle.
4. Raise saddle to vehicle support point vehicle, continue to rotate handle clockwise until load support point is secure. Do not raise any higher than load stability will allow. 5. Check to ensure vehicle is secure before working on, around or under. LOWERING THE JACK STAND 1. Ensure that all tools, equipment and personnel are clear before lowering load. 2. DO NOT EVER LOWER STAND UNLESS VEHICLE AND COMPNENTS ARE 100% SUPPORTED SECURELY. DO NOT EVER ASSUME LOAD IS SECURE, CHECK BEFORE LOWERING. 3.
LUBRICATION A periodic coating of light lubricating oil to pivot points will help to ensure that pump piston linkages move freely. Note: Never apply oil to the saddle. If saddle extension threads require lubrication; clean thread surfaces with a clean, dry cloth, then apply a drop of bearing grease to the threads. Distribute as evenly as possible along the threaded post.
MAINTENANCE INSTRUCTIONS If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance.
PARTS DIAGRAM 14
PARTS LIST Index # Part No. Description Qty. 1 GB/T 70 Nut Bolt M6X10 4 2 TRF42009-01 Rubber Pad 1 3 TRF42009-02 Saddle 1 4 GB/T 5781 Nut Bolt M10X20 6 5 GB/T 97.1 Washer 10 9 6 GB/T6170 Nut M10 6 7 TRF42009-03 L-Bracket (Middle Bridge) 1 8 TRF42009-04 component hardware 3 9 TRF42009-05 Lock Plate 1 10 TRF42009-06 Support Pillar 3 11 TRF42009-07 Pull Rod 3 12 GB/T 5781 Nut Bolt M8X16 12 13 GB/T 97.
Limited Warranty Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
