500-LB. HIGH POSITION HOIST STAND OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is designed for certain applications only. The distributor cannot be responsible for issues arising from modification.
IMPORTANT SAFETY CONSIDERATIONS JACK STAND USE AND CARE Do not modify the jack stand in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. There are specific applications for which the jack stand was designed. Always check of damaged or worn out parts before using the jack stand Broken parts will affect the jack stand operation. Replace or repair damaged or worn parts immediately.
GENERAL SAFETY INSTRUCTIONS * Position the Auxiliary Stand Position the jack stand to only support on the areas of the vehicle as specified by the vehicle manufacturer. * Always Support Load After lifting the vehicle always support the load with appropriately before working on the vehicle. * Do Not Overload Do not overload this equipment beyond its rated capacity. Overloading this equipment beyond its rated capacity can cause damage to or failure.
ASSEMBLY Use the exploded drawing as your guide to assemble, Lay all parts and assemblies out in front of you before beginning. The following procedure is recommended: All numbers in parenthesis () refer to the index number from the parts breakdown. 1. Familiarize yourself with the Jack Stand. 2. Attach (11) pillar base to (10) stand base. Check that both parts are secure to each other.
3. Attach (9) upright to (11) pillar base. 4. Use hardware include to attach upright to pillar base. Place (13) washer M16, then insert (12) pillar roll pin M16x60 through holes on the pillar base. Secure roll pin with (14) washer M16 and (15) spring clip.
5. Attach (2) handle to (3) threaded rod. Then attach (20) roll pin M4x25 to (3) threaded rod. 6. With the upright in the standing position insert (6) lower bearing base, (7) ball bearing assembly and (8) upper bearing base onto (5) upright bearing seat. 7. Attach (1,3, 4) threaded rod column assembly on (6,7,8) bearings and slide shaft inside (9) upright. Use caution when installing and lowering threaded rod column assembly.
. Insert (19) foot pedal into slot between (11) pillar base weldment. Use hardware include to attach upright to pillar base. Place (21) washer M12 on (16) pin M12, then Insert (16) foot pedal pin M12x35 through (11) pillar base weldment hole slot. Secure (16) foot pedal pin with (17) washer M12 and (18) spring clip. 9. Check that all hardware is secure and tight. 10. Auxiliary Stand is now ready for use.
OPERATING INSTRUCTIONS RAISING THE JACK STAND 1. 2. 3. 4. 5. Adjust height by rotating the handle CLOCKWISE. Check to ensure ratchet is secure before loading/un/loading. Carefully position stand so that load is centered on stand’s saddle. Raise saddle to vehicle support point vehicle, continue to rotate handle clockwise until load support point is secure. DO NOT RAISE ANY HIGHER THAN LOAD STABILITY WILL ALLOW. Check to ensure vehicle is secure before working on, around or under. LOWERING THE JACK STAND 1.
MAINTENANCE INSTRUCTIONS If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use. Follow lubrication and storage instructions for optimum product performance.
ASSEMBLY DIAGRAM 11
PARTS LIST Index # Description Item # Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 Saddle Pad Saddle Threaded Rod Adjusting Handle Upright Bearing Seat Upright Lower Bearings Base Upright Ball Bearing Assembly Upright Upper Bearings Base Upright Base Pillar Base Pillar PIN M16x60 Pillar Plain Washer M16 M7501.0-1 M7501.0-2 M7501.0-3 M7501.1 Upright Weldment M7501.0-4 M7501.2 M7501.0-5 M7501.0-6 M7501.0-7 M7501.0-8 GB 662 GB/T 97.
Limited Warranty Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
