Push Trolley Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This trolley is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 5 Specific Operation Warnings .......................
Intended Use The Strongway Push Trolley is suitable for loading and unloading goods in factories, mines, farms, construction sites, wharves, docks, and warehouses. Technical Specifications Model Capacity (lb.) Beam Flange Min Width (in.) Beam Flange Max Width (in.) Length A (in.) Length B (in.) Length C (in.
Geared Trolley Important Safety Information ⚠WARNING Read and understand all instructions. Failure to follow all instructions may result in serious injury or property damage. The warnings, cautions, and instructions in this manual cannot cover all possible conditions or situations that could occur. Exercise common sense and caution when using this tool. Always be aware of the environment and ensure that the tool is used in a safe and responsible manner.
of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust. Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area. Some of these hazards may be hidden from your view and may cause personal injury and/or property damage if contacted.
Specific Operation Warnings ⚠WARNING Do not exceed the rated load capacity. The rated load capacity of the hoist must not exceed the rated load capacity of the trolley. Ensure the path of the trolley is clear before installation. Before each use, inspect trolley and verify that all wheels make substantial contact with the beam flange and are secure. Adjust if necessary. Only use on a flat, level surface. Do not use to lift people or animals. Not for use by or around children.
Maintenance Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease. The following chart is based on a normal operation schedule. Maintenance Interval Daily after operating Quarterly (every 3 months) Maintenance Point Keep all parts clean and dry.
Parts Diagram Item # 57076, 57077, 57078, 57079, 57080 Parts List Reference 1 2 3 4 5 6 7 Part Number 1 2 3 4 5 6 7 Part Description Side plate Wheel Bearing Axle ring Bearing ring Hole ring Equalizer pin Page 9 of 13 Quantity 2 4 4 4 4 4 1
Parts Diagram Item # 57081, 57082, 57083 Parts List Reference 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part Description Side plate Wheel Bearing Axle ring Bearing ring Hole ring Equalizer pin Tooth gear Driven spindle Right side gear case assembly Copper sleeve Catch pin Chain wheel Spacer washer Hex castle nut Split pin Chain Roll spindle Page 10 of 13 Quantity 1 4 4 4 4 4 1 2 1 1 1 1 1 1 1 1 1 1
Reference 19 20 21 22 Part Number 19 20 21 22 Part Description Roll sleeve Axle sleeve Spring washer Hex nut Quantity 1 1 1 1 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
