WARNING TO PREVENT FIRE OF SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The Caution Marking is located at the bottom enclosure of the apparatus. The Rating plate is located at the bottom enclosure of the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instruction.
CAUTION Follow the advice below for safe operations. ON PROTECTION AGAINST LASER ENERGY EXPOSURE As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the casing. Stop operation immediately if any liquid or solid object should fall into the cabinet. Do not touch the lens or poke at it. If you do, you may damage the lens and the player may not operate properly. Do not put anything in the safety slot.
DEAR STUDEBAKER CUSTOMER Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
LOCATION OF CONTROLS 1 2 3 LED DISPLAY SPEAKER CD COMPARTMENT 16 17 18 4 5 6 WATCH HOLDER USB CHARGING PORT DC IN JACK 19 20 21 STOP 7 REPEAT BUTTON CLK SET / MEM / PROG BUTTON / PAIR / BUTTON / TUN+ BUTTON / TUN- BUTTON / BUTTON CLOCK BACKUP BATTERIES COMPARTMENT 8 FM ANTENNA 9 AUX IN JACK 10 WIRELESS CHARGING PADS 11 SOURCE BUTTON 12 POWER BUTTON 22 AL2 / M+ BUTTON 23 24 25 26 27 AL1 / M- BUTTON EQ / SCAN BUTTON VOLUME- / VOLUME+ BUTTON WIRELESS CHARGE INDICATORS MICROPHONE OF THE UNIT 13
Note: All buttons on the unit can also be operated by remote control.
Install / Remove Batteries of Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover. Notes: Batteries shall not be exposed to excessive heat such as placing under the sunlight or near a fire. Please make sure the batteries are installed with their correct polarities. Do not mix old and new batteries.
Battery Back-up system The unit is equipped with a battery back-up system. It requires 2 x ‘AAA’ (UM-4) batteries (Not included). Open the battery door on the bottom of the unit. Insert the batteries into the CLOCK BACKUP BATTERIES COMPARTMENT (#7) and make sure the positive and negative (+ or -) sides of the batteries are in contact with the corresponding terminals in the batteries compartment . Replace the battery door.
SETTING THE CLOCK The LED DISPLAY (#1) will flash when the unit is plugged in for the first time. The unit is now in standby mode. Setting the Time: 1. In standby mode, press and hold the CLOCK SET BUTTON (#17) until the hour digits of the clock display begin to flash. 2. Repeatedly tap the BUTTON (#20) or BUTTON (#19) to set the hour. Press and hold the buttons for fast reverse/advance setting. Make sure the correct AM or PM time is selected when setting the hour.
7. Tap the ALARM 1 BUTTON (#23) to confirm the minute setting. The wake up option will flash on the LED DISPLAY (#1) to prompt for input. 8. Tap the BUTTON (#19) or BUTTON (#20) to select the wake up option (bb – alarm sound or rAd – FM radio). 9. Tap the ALARM 1 BUTTON (#23) to confirm the wake up option setting. The volume level digits will flash on the LED DISPLAY (#1) to prompt for input. BUTTON (#19) or BUTTON (#20) to select the volume level. 10. Tap the 11.
Setting the alarms ON/OFF: 1. In Standby mode, press and hold the ALARM 1 BUTTON (#23). The Alarm 1 icon will light and the “OFF or ON” of alarm time will flash. BUTTON (#19) or BUTTON (#20) repeatedly to select the Alarm “ON” or 2. Tap the “OFF”. 3. Tap the ALARM 1 BUTTON (#23) again to confirm. 4. The corresponding AL1 icon will light when the alarm is enabled. The corresponding AL1 icon will turn off when the alarm is disabled. 5.
Set the radio presets: The unit allows you to store up to 20 FM for easy recall at any time. BUTTON (#12) to turn the unit on. 1. Tap the POWER 2. Tap SOURCE BUTTON (#11) repeatedly to select FM radio mode. 3. The FM icon will turn on and the frequency will show on the LED DISPLAY (#1). 4. Tune to the desired radio station by “MANUAL” or “AUTO” tuning method. 5. Tap the MEM BUTTON (#17) to enable program mode, “P01” appears in display and flashing.
7. While playing, press the PLAY/PAUSE BUTTON (#18) to pause, the play icon will flash on the LED DISPLAY (#1). Press PLAY/PAUSE BUTTON (#18) again to resume playing. 8. Tap VOLUME + / VOLUME - (#25) to the desired volume level. 9. Press CD STOP BUTTON (#21) to stop playing. BUTTON (#12) to turn off the unit. 10. Tap the POWER Notes: If skipping occurs during CD play, try turning the volume down. Do not open the CD DOOR when a CD is playing.
BLUETOOTH OPERATION BUTTON (#12) to turn on the unit and the POWER INDICATOR (#13) 1. Tap the POWER will light. 2. Tap the SOURCE BUTTON (#11) repeatedly to select Bluetooth mode. will turn on and flash on the LED DISPLAY (#1). 3. The Bluetooth icon 4. Turn on the Bluetooth function of your device and enable the search or scan function to find the SB5050. 5. Select SB5050 from the device list when it appears on your device screen.
5. 6. 7. 8. Notes: If you have several Bluetooth receivers, switch off those receivers that are not in use and place the one to be linked near the unit to avoid SB5050 linked to other unwanted Bluetooth enabled devices. The effective distance between your external device and this apparatus is within 10 meters (30 feet). SB5050 will auto scan and pair with your Bluetooth receiver nearby, the Bluetooth icon will change to solid to indicate a connection has been established.
SLEEP OPERATION The SLEEP TIMER feature allows you to turn off the unit automatically after a designated time has elapsed. 1. Select CD, FM, AUX or Bluetooth Mode and begin playing music from the selected source. 2. Tap the SLEEP BUTTON (#14) to enter sleep mode. 3. Repeatedly tap the SLEEP BUTTON (#14) to select the sleep timer 10 – 30 – 60 – 90 – 120 - OFF (in minutes). The unit will play for the selected length of time then turn off automatically. 4.
CAUTION: Remove your phone from any metal or magnetic protective case before placing it on the Charging Pad. Do not place any metal objects or magnetic-striped devices on the Charging Pads. Doing so could damage the object or this unit. Qi compatible phones with metallic finishes will charge normally. Qi WIRELESS CHARGING FAQ AND COMPATIBILITY Visit www.spectraintl.
EQ OPERATION This unit provides 5 differences sound modes to enhance your listening experience. You can select the desired effect by tapping the EQ BUTTON (#24) repeatedly to get the effect you want: FLAT ROCK CLASSIC JAZZ POP Note: FLAT is EQ turned off and no EQ icon will light. CARE AND MAINTENANCE 1. 2. 3. 4. 5. Do not subject the unit to excessive force, shock, dust or extreme temperatures. Do not tamper the internal components of the unit. Clean your unit with a dry cloth.
TROUBLE SHOOTING GUIDE If you experience difficulties in the use of this workstation, please check the following or call 1-800-777-5331 for Customer Service and support. Symptom The unit does not respond (no power) Unit is ON but there is low or no volume FM no sound Bluetooth no sound Possible Cause The unit is disconnected from the AC outlet. The AC outlet has no power. Volume set too low. Unit not in Radio mode. Unit is not linked with your Bluetooth enabled device. Unit placement out of range.
No charging from the USB port Replace the USB cable or try reconnect it again. The USB cable is damaged or not securely attached. Wireless charging is There is a protective case on slow the surface of the smart phone. Take off the protective case from the smart phone. No charging from wireless pads Move the device around the wireless pad until the wireless charging indicator light. Change to use USB charging port Device is not in correct position . The device does not support wireless charging.
1 YEAR LIMITED WARRANTY AND SERVICE VALID IN THE U.S.A. ONLY SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective materials or factory workmanship for a period of 1 year from the date of original customer purchase and provided the product is utilized within the U.S.A. This warranty is not assignable or transferable.
