Thank you for purchasing our Studio Designs, Inc. Gracias por comprar nuestro mueble Studio Designs, Inc. Merci d’avoir acheté un meuble Studio Designs, Inc. FUSION CRAFT CENTER WITH 24" TRAY #10102 Charcoal/White • Carbón/Blanco • Charbon/Blanc Office: 562.942.0492 Product Support Line: 866.942.0492 Rev. 6.12.
ASSEMBLY INSTRUCTIONS - IMPORTANT: Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when assembling the unit and always set the parts on a clean, soft surface. Screwdriver required for assembly. If you require any assistance with assembly, parts, or information on other products, please visit our website: www.studiodesigns.com or call or write us. Check screws, nuts and bolts periodically (or every 6 months). Tighten if necessary.
PARTS LIST / LISTA DE PARTES / LISTE DES PIÈCES DÈTACHÉES DESCRIPTION / DESCRIPCIÓN / DESCRIPTION QTY / CANT/ QTÉ 1. Left Leg Pata Izquierda Jambe Gauche 1 2. Right Leg Pata Derecha Jambe Droite 1 3. Left Arm Brazo Izquierdo Bras Gauche 1 4. Right Arm Brazo Derecho Bras Droite 1 5. Top Mesa Table 1 6. Side Shelf Estante Lateral Étagère Laterale 1 7. Rear Bar Barra Trasera Barre Arrière 1 8. Front Bar Barra Delantera Barre Avant 1 9.
PARTS LIST / LISTA DE PARTES / LISTE DES PIÈCES DÈTACHÉES DESCRIPTION / DESCRIPCIÓN / DESCRIPTION QTY / CANT/ QTÉ 13. Basket Canasta Corbeille 2 14. Pencil Ledge Borde para Lápiz Bord pour Crayon 1 15. Ratchet Arm Brazo de Trinquete Support à Cliquet 1 16. L Bracket Soporte en forma L Support en forme L 2 17. Knob Perilla Molette 2 18. Floor Leveler Nivelador de Piso Niveleur de Plancher 4 19. Nut Tuerca Écrou 4 20. Pin Pasador Goujon 4 21.
PARTS LIST / LISTA DE PARTES / LISTE DES PIÈCES DÈTACHÉES DESCRIPTION / DESCRIPCIÓN / DESCRIPTION QTY / CANT/ QTÉ 25. Allen Bolt - 1/4" x 5/8" Perno Allen - 6mm x 15mm Boulon Allen - 6mm x 15mm 2 26. Allen Bolt - 5/32" x 1/2" Perno Allen - 4mm x 12mm Boulon Allen - 4mm x 12mm 8 27. Allen Bolt - 1/4" x 1-1/8" Perno Allen - 6mm x 30mm Boulon Allen - 6mm x 30mm 4 28. Allen Bolt - 1/4" x 1-1/8" Perno Allen - 6mm x 28mm Boulon Allen - 6mm x 28mm 4 29.
1 Do not fully tighten any bolt until step 4. No apriete completamente nungun perno hasta el paso 4. Ne pas serrer aucun boulon jusqu’à l’étape 4. 19 10 19 2 22 18 1 22 18 18 18 Fusion Craft Center with 24" Tray p.
2 Screw Knobs (17) into first hole in Left and Right Arms (3 and 4). Atornille Perillas (17) en primer agujero en Brazo Izquierdo y Derecho (3 y 4). Visser Molettes (17) dans le premier trou dans Bras Gauche et Droite (3 et 4). 4 3 21 17 9 21 17 21 Fusion Craft Center with 24" Tray 11 p.
3 22 15 21 21 7 8 21 21 Fusion Craft Center with 24" Tray p.
4 22 22 37 37 26 12 12 26 26 26 Repeat step to assemble two more Rails (12) on left side (see arrows). Fully tighten all bolts from Step 1-4. Repita el paso para montar dos más Carriles (12) en el lado izquierdo (vea flechas). Apriete completamente todos los pernos del paso 1-4. Répéter l’étape pour assembler deux Rails (12) supplémentaires sur le côté gauche (voir flèches). Serrer tous les boulons des étapes 1-4. Fusion Craft Center with 24" Tray p.
5 Insert Baskets (13) and Insert one Pin (20) into front holes in Rails to prevent Basket from falling out. Slide Shelf (6) to edge of Rail (12), then attach Screws (23). Inserte las Canastas (13) e inserte un Pasador (20) en los agujeros delanteros en los Carriles para evitar que caiga la Canasta. Deslice el Estante (6) hasta el borde del Carril (12), luego fije los Tornillos (23).
6 CAUTION!: Use two people. ¡PRECAUCIÓN!: Use dos personas. PRÉCAUTION: Utilisez deux personnes. Attach Brackets (16), flip Top (5) over and attach to Arms (3 and 4) using Allen Bolts (25), then attach Ratchet Arm (15). Fije los Soportes (16), de vuelta la Mesa (5) y fije a los Brazos (3 y 4) usando Pernos Allen (25), despues fije el Brazo de Trinquete (15). Fixez les Supports (16), tournez le Table (5) et fixer aux Bras (3 et 4) à l’aide des Boulons Allen (25), puis fixer le Support à Cliquet (15).
7 31 30 32 24 14 23 23 Leave Phillips Screws (23) slightly loose so Pencil Ledge (14) can slide. Deje los Tornillos (23) legeramente sueltos para que pueda deslizar Borde (14). Laisser les Vis (23) légèrement desserrées ainsi le Bord (14) peut glisser. Lift the Top so it’s angled, slide Metal Tray (30) over edge of table, and secure using Allen Screws (24) (do not overtighten). Insert Cup (31) and Foam Organizer Tray (32) into slots. Foam Tray can also be placed on shelf as a mobile organizer.
8 34 28 29 29 35 36 29 27 27 29 Note the curve on the Legs - see arrows. Tenga en cuenta la curva en las Patas - vea las flechas. Noter la courbe sur les Jambes - voir les flèches. 33 Fusion Craft Center with 24" Tray p.
LIMITED WARRANTY Studio Designs (the “Company”) warrants to the original purchaser that this product will be free from defects in its workmanship and materials, under normal residential use and service conditions, as described herein.