STUDIO 90 90 -- STUDIO STUDIO 90 90 STUDIO MIDI PEDALBOARD PEDALBOARD MIDI PLUS PLUS
INDICE ITALIANO ENGLISH DEUTSCH STUDIO 90 SPLIT TRANSPOSE DATI TECNICI Pag. " " 2 2 2 SPLIT TRANSPOSE TECHNICAL DATA STUDIO 90 CARATTERISTICHE RESET GENERALE COLLEGAMENTI ACCENSIONE USCITE MIDI INGRESSO MIDI PARAMETRI E VALORI PROGRAMMAZIONE: SPLIT POINT TRANSPOSE OCTAVE CHANNEL MIDI PRESET FOOT-SWITCH/PITCH & MODULATION CONTROL VEL. SENS. TOUCH VEL. SENS. RELEASE Pag. " " " " " 3 4 4 4 4 4 5 " " " " " 6 8 9 9 10 " " " 10 10 10 Page 14 " 14 " 14 TRENNUNG TRANSPOSER TECHNISCHE DATEN Pag.
STUDIO 90PLUS STUDIO 90 SPLIT TRANSPOSER LOWER TRANSPOSER UPPER SPLIT TRANSPOSER 1 2 3 4 5 6 7 8 9 0 PLUS LOWER UPPER Param. Value Prog. MIDI OUTS FOOT - SWITCH POWER INPUT ON OFF SPLIT Per «splittare» la tastiera in due parti, è sufficiente premere la nota dalla quale si desidere dividere la tastiera, e premere quindi il tasto «SPLIT».
RESET GENERALE (STUDIO 90 Plus) Spegnere la tastiera. Tenere premuti i tasti "ENTER" e "1" della tastiera numerica. Sempre tenendo premuti i suddetti tasti, riaccendere la tastiera. Importante: una volta resettata la tastiera, tutti i programmi vengono cancellati ed entra in funzione un programma di default.
POSSIBILITA' DI PROGRAMMAZIONE DELLA STUDIO 90 Plus DISPLAY TASTI NUMERICI A SPLIT 1 PAR. 00 Param. Value Prog. 1 2 3 4 5 6 7 8 9 0 Enter SPLIT 2 PAR. 01 CHANNEL MIDI 1 PAR. 08 CHANNEL MIDI 2 PAR. 09 CHANNEL MIDI 3 PAR. 10 TRANSPOSER 1 PAR. 02 TRANSPOSER 2 PAR. 03 TRANSPOSER 3 PAR. 04 OCTAVE 1 PAR. 05 OCTAVE 2 PAR. 06 OCTAVE 3 PAR. 07 TASTO ENTER TASTO PROGRAMMA TASTO VALUE TASTO PARAMETRI B SPLIT POINT - Punto di divisione (Parametro 00 e 01).
Esempio: Nel programma N. 12 il punto di divisione sinistro si trova sul tasto 17 e il punto di divisione destro nel tasto 42. Operazione 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Tasto PROG. 12 ENTER PARAM. 00 ENTER VALUE 17 ENTER PARAM. 01 ENTER VALUE 42 ENTER Display lampegg. 12 lampegg. 00 lampegg. 17 00 lampegg. 01 lampegg.
MIDI PEDALBOARD PRESET 1, 2, 3 (Parametri 11, 12, 13) La scelta dei suoni dei vari expanders e strumenti collegati alla STUDIO 90 Plus, avviene attraverso questi parametri, che offrono una possibilità di scelta tra 100 suoni (00-99). CHANNEL MIDI OCTAVE PRESET Esempio: Nel programma N. 47 si dovrà mettere la parte centrale della tastiera con il suono 16. Dopo aver chiamato il programma che ci interessa, si procede: Operazione 1 2 3 4 5 6 Tasto Display Cosa succede PARAM.
POSSIBILITA' DI PROGRAMMAZIONE DELLA MIDI PEDALBOARD POSIZIONE DELLE OTTAVE Dopo l'attivazione del tasto "OTTAVA" premendo semplicemente uno dei tasti della pedaliera, si decide l'ottava da assegnare: - DO = Ottava più bassa - DO = Ottava sopra - RE = Ottava sopra - e così via fino ad arrivare all'ultimo - DO = Ottava più alta. CANALE MIDI Dopo l'attivazione del tasto "CH. MIDI", si assegna il canale MIDI premendo uno dei tasti della pedaliera.
STUDIO 90PLUS STUDIO 90 SPLIT TRANSPOSER LOWER TRANSPOSER UPPER Param. Value Prog. SPLIT 1 2 3 4 5 6 7 8 9 0 PLUS Enter TRANSPOSER LOWER UPPER INTRODUCTION: Thank you for purchasing the FATAR Studio-90 Plus, the finest feeling master controller on the market today. The action is a result of many years of engineering that went into the keyboard mechanism. There are actually hammers that strike a surface that simulates a piano string.
CONNECTIONS: Look at figure #2 and #3. The functions are the same, but the location of the midi outs and foot switch controls are separated from the power section. You will find this configuration on the ST-90 Plus in the cabinet. FUSE LINE POWER MIDI OUT FOOT-SWITCH fig. #2 1 2 POWER ON FOOT-SWITCH MIDI OUT 3 MIDI CONTROL PROGRAM CHANGE LINE FUSE 1 2 3 MIDI CONTROL PROGRAM CHANGE OFF FOOT-SWITCH PROGRAM CHANGE POWER ON LINE FUSE fig.
SECTION I: GETTING STARTED In this section we will explore the possibilities of the Studio-90 Plus in its entirety. Do not skip any pages. Since each function depends on a previous parameter, it is probably best to read carefully from here on out. LET'S GET STARTED In this section you should get ready for hands on experience. Plug in one end of a midi cable to the output jack of the controller. Plug the other end into the midi input of your sound module.
At this time the keyboard is asking you at what key location on the keyboard would you like your first split. You will see a number in the screen. No matter what that number is now, please press 27 on the numeric key pad. This number will flash. Now press the ENTER key to lock this position into the memory of the keyboard. You have just set parameter 00 (SPLIT LEFT) to the 27th key on the keyboard, that is musically speaking, B in the 3rd octave or B3.
CHANNEL MIDI: Parameters 08, 09, and 10 are midi channel functions. You will locate them on the parameter chart as CHANNEL MIDI 1, 2 and 3. Again, 1, 2, and 3, refers for zones one, two, and three. The VALUES of these parameters are midi channels 1 through 16, represented by 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, giving us access to all the midi channels in the specification. Up to this point you have created a single midi channel. This midi channel runs across the keyboard.
envelope. The result is a fast or slow release of the sound. VALUE 99 has a quick response and 00 has a slow response. The default of the keyboard is 50. Program parameter 18 in the same manor as the other parameters. NOTE: In order for this function to work, the sound source must have the capability of receiving such a command. Some sound sources let you use this release function for other control parameters. Check your sound source owner's manual for details.
Two Sounds Across Keyboard 00 = 88 01 = 88 02 = 00 03 = 00 04 = 00 05 = 00 06 = 00 07 = 10 08 = 01 09 = 02 10 = 03 11 = 00 12 = 34 13 = 08 14 = 03 15 = 03 16 = 03 17 = 50 18 = 50 - Note: Part 1 & 2 across keyboard, part 3 off. One Sound Left of C5, One Sound Right of C5, One Sound Across 00 = 40 01 = 40 02 = 00 03 = 00 04 = 00 05 = 00 06 = 00 07 = 10 08 = 02 09 = 01 10 = 03 11 = 33 12 = 00 13 = 34 14 = 03 15 = 03 16 = 03 17 = 50 18 = 50 - Note: Part 1 to C5, part 3 from C#5 to top of keyboard.
MIDI PEDALBOARD PARAMETER CHART Program Name CHANNEL MIDI OCTAVE Program Number PRESET MP 1 00 = 01 = 02 = 03 = 04 = 05 = 06 = 07 = 08 = 09 = 10 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = 8 4 2 1 OCTAVE CH. MIDI PRESET With the MIDI PEDALBOARD you have a wider MIDI system, and you also have the possibility to change the sounds and the octave in an expander. The MIDI PEDALBOARD is manufactured so that all functions can be easily executed by feet.
PROGRAMMING POSSIBILITIES POSITIONS OF OCTAVES By depressing OCTAVE switch, you can assign a certain bass pedal octave positions to any Pedalboard key. example: - C on Pedal = Lower octave - C # on Pedal = One octave more - D on Pedal = One octave more - C high = Octave heigher MIDI CHANNELS By depressing CH. MIDI switch you can the MIDI channel to any Pedalboard key.
STUDIO 90 SPLIT STUDIO 90 Plus TRANSPOSER LOWER TRANSPOSER UPPER SPLIT TRANSPOSER LOWER UPPER Param. Value Prog. MIDI OUTS FOOT - SWITCH POWER INPUT ON OFF TRENNUNG Um die Tastatur in zwei Teile zu trennen, genügt es, die Note zu drücken, von der die Tastatur geteilt werden soll, dann druckt man die Taste "SPLIT". Nach der Trennung, teilt sich die Tastatur in zwei Teile: der Unterteile (LOWER) ist im MIDI 1 Kanal un der Oberteil (UPPER), im MIDI 2 Kanal.
GENERALPROGRAMMIERUNG (STUDIO 90 Plus) Das Manual ausschalten. Die Tasten "ENTER" und "1" von der Nummerntastatur gedrückt halten. Die o.g. Tasten immer gedrückt halten und gleichzeitig das Manual einschalten. Wichtig: Die Generalprogrammierung löscht alle Programme die Sie gespeichert haben. ANSCHLÜSSE Bevor Sie mit dem Spiel auf Ihrem STUDIO 90 Plus beginnen können, müßen Sie die notwendigen Anschlüßen herstellen.
DIE PROGRAMMIERUNG DISPLAY NUMERIC KEYS 1 Param. Value Prog. 1 2 3 4 5 6 7 8 9 0 SPLIT 1 PAR. 00 Enter SPLIT 2 PAR. 01 CHANNEL MIDI 1 PAR. 08 CHANNEL MIDI 2 PAR. 09 CHANNEL MIDI 3 PAR. 10 TRANSPOSER 1 PAR. 02 TRANSPOSER 2 PAR. 03 TRANSPOSER 3 PAR. 04 OCTAVE 1 PAR. 05 OCTAVE 2 PAR. 06 OCTAVE 3 PAR. 07 ENTER KEY PROGRAM KEY VALUE KEY PARAMETER KEY SPLITPUNKTE(Parameter 00 und 01). Das Studio 90 Plus hat zwei völlig frei wählbare Splitpunkte.
Beispiel: Im Programm Nr. 12 soll der linke Spitpunkt bei Taste Nr. 17 und der rechte Splitpunkte bei Taste Nr. 42 liegen. Schritt Taster Display Aktion 1 PROG. Programm-Taster aktivieren 2 12 12 blinkt Eingabe der Programm-Nummer 3 ENTER 12 Programm-Nr. 12 ist aktiv 4 PARAM. * Parameter-Taster aktivieren 5 00 00 blinkt Eingabe der Param. 00 ="Splitpunkt links" 6 ENTER * "Splitpunkt links" - Param. ist aktiviert 7 VALUE * "Werte - Taster" aktivieren 8 17 17 blinkt Taste Nr.
MIDI-PEDAL PRESET 1, 2, 3 (Parameter 11, 12, 13) Die Wahl der Klangfarben des angeschlossenen Instrumentes für jeden der Manualbereich nehmen Sie über die Parameter "11, 12 und 13" vor. Bis zu 100 verschiedene Klänge und Sounds (00-99) können über den aktiven MIDI-Kanal auf gerufen und zugeordnet werden. Beispiel: Im Programm Nr. 47 soll der mittlere Manualbereich mit der Klangfarbe Nr.16 belegt werden Schritt Taster Display 1 2 3 4 5 6 7 8 9 PARAM. 47 ENTER PARAM.
PROGRAMMIERMÖGLICHKEITEN 1.0 OKTAVLAGE Nach dem Betätigen des Tasters "OKTAVE" läßt sich die Oktavlage des Basspedals über die Pedaltasten einstellen: - C = tiefste Oktave - Cis = eine Oktave höher u.s.w. Nach jedem Betätigen des Tasters "OKTAVE" kann man immer nur einen OktaveWert einstellen. Ggf. erneut den "OKTAVE"-Taster drücken. 2.0 MIDI-KANAL Nach Betätigen des Tasters "Ch. MIDI" laßen sich in gleicher Weise die MIDIKanäle einstellen: - C = MIDI-Kanal 1 - Cis = MIDI-Kanal 2 u.s.w. 3.
