ITEM #1599749 TENSION POLE SHOWER CADDY Style Selections is a trademark of LF, LLC. All Rights Reserved. MODEL #2165WWMV Español p. 10 ATTACH YOUR RECEIPT HERE ADJUNTE SU RECIBO AQUÍ Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Sunday.
TABLE OF CONTENTS Package Contents .......................................................................................................................... 2 Hardware Contents ........................................................................................................................ 3 Safety Information ........................................................................................................................... 3 Preparation ......................................................
HARDWARE CONTENTS (shown actual size) AA BB CC Small End Cap Large End Cap Wedge Qty. 1 Qty. 1 Qty. 4 Spacer DD Qty. 3 GG EE FF Transition Ring Spring Stopper Tape Strip Qty. 1 Qty. 2 Qty. 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before cutting, drilling or hammering into any wall surface, verify the location of electrical, plumbing and gas lines. Cutting any of these may cause serious injury.
ASSEMBLY INSTRUCTIONS 1. Measure the distance between the tub ledge or the shower stall floor to the ceiling to the nearest half inch. 1 tub ledge (opening height) NOTE: See the below chart to determine what tubes (C), (D) and (E) are needed. NOTE: No matter the distance, tubes (A) and (B) are ALWAYS used. Please write down your measurements, tubes and spacers needed below, you will need this later.
ASSEMBLY INSTRUCTIONS 2. NOTE: THIS ASSEMBLY IS SHOWN FOR 97 IN. OPENING HEIGHT. The following assembly should be modified based on your opening height, SEE CHART ON PAGE 4. 2 DD C Place a wedge (DD) (tapered or rounded end up) on a long-tapered tube (C) approximately half way down and slide a shelf (F) down the tube and fit over the wedge (DD). Place another wedge (DD) (tapered or rounded end up) on a long-tapered tube (C) and slide another shelf (F) down the tube and fit over the wedge (DD).
ASSEMBLY INSTRUCTIONS 4. Peel the paper backing off the double stick tape on the mirror frame (G). 4 Slide the frame tab under the desired shelf (F) and attach to the underside of the shelf front, as shown. IMPORTANT: Be sure of the mirror’s location, once the mirror is in place, it is permanent. double stick tape F G 5. P lace the tapered end of the medium tube (D) into the untapered end of the long tube (C), as shown.
ASSEMBLY INSTRUCTIONS 6. Place the large end cap (CC) onto the short tapered tube (E). 6 bottom tube assembly Place the tapered end of the short tapered tube (E) into the untapered end of the bottom tube assembly, as shown. tapered end at the top E Hardware Used CC x1 Large End Cap 7. N OTE: ASSEMBLY SHOWN FOR 96 IN. OPENING HEIGHT. The following assembly should be modified based on your opening height, SEE CHART ON PAGE 4.
ASSEMBLY INSTRUCTIONS 8. Place the small end cap (BB) onto the 3/4 in. tube (A). 8 BB A Insert the transition ring (EE) into the straight tube (B). Slide the 3/4 in. tube (A) through the transition ring (EE) and into the straight tube (B), as shown. EE A Place the tape strips (GG) around the seams of the tubes. NOTE: After inserting the 3/4 in. tube (A) into the straight tube (B) ensure that the transition ring (EE) fits snuggly over the straight tube (B).
ASSEMBLY INSTRUCTIONS 10. Install the soap dish (I) on any shelf (F). The tabs on the bottom of soap dish (I) snap into place in the holes in the shelves (F). 10 I NOTE: The soap dish can be inserted in various locations on each shelf according to your preference. (Once installed, the soap dish can be removed by firmly pressing in and up on the tabs from under the shelf.) F CARE AND MAINTENANCE Cleaning with a dry cloth may be sufficient, but for other stains or marks wipe gently with a damp cloth.
ARTÍCULO #1599749 POSTE ORGANIZADOR PARA DUCHA Style Selections es una marca de LF, LLC. Todos los derechos reservados. Número de serie MODELO #2165WWMV Fecha de compra ¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro Departamento de Servicio al Cliente al 1-877-888-8225, de lunes a domingo de 8 a.m. a 8 p.m., hora estándar del Este.
ÍNDICE Contenido del paquete ................................................................................................................. 11 Aditamentos ................................................................................................................................. 12 Información de seguridad .............................................................................................................. 12 Preparación ......................................................................
ADITAMENTOS (se muestran en tamaño real) AA BB CC Tapa de extremo pequeña Tapa de extremo grande Cant. 1 Cant. 1 Espaciador DD Cuña Cant. 4 Cant. 3 GG EE FF Anillo de transición Tope de resorte Tira de cinta Cant. 1 Cant. 2 Cant. 1 INFORMACIÓN DE SEGURIDAD Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el producto. • Antes de cortar, taladrar o martillar en cualquier superficie, verifique la ubicación de las tuberías de electricidad, agua y gas.
INSTRUCCIONES DE ENSAMBLAJE 1. Mida la distancia entre el borde de la bañera o el piso del compartimiento para ducha hasta el techo con una precisión de media pulgada (1,27 cm). 1 borde de la bañera (altura e la abertura) NOTA: consulte la siguiente tabla para determinar qué tubos (C), (D) y (E) son necesarios. NOTA: independientemente de la distancia, los tubos (A) y (B) se utilizan SIEMPRE. Anote sus medidas, los tubos y los espaciadores necesarios a continuación, los necesitará más adelante.
INSTRUCCIONES DE ENSAMBLAJE 2. NOTA: ESTE ENSAMBLAJE SE MUESTRA PARA UNA ALTURA DE ABERTURA DE 246,38 CM. El siguiente ensamblaje se debe modificar en base a su altura de abertura, CONSULTE LA TABLA DE LA PÁGINA 4. 2 DD C Coloque una cuña (DD) (extremo cónico o redondeado hacia arriba) en un tubo cónico largo (C) aproximadamente a la mitad; luego, deslice un estante (F) por el tubo y colóquelo sobre la cuña (DD).
INSTRUCCIONES DE ENSAMBLAJE 4. Despegue el papel que cubre la cinta adhesiva doble en el marco del espejo (G). 4 Deslice la pestaña del marco debajo del estante deseado (F) y colóquelo en la parte inferior del frente del estante, como se muestra. IMPORTANTE: asegúrese de la ubicación del espejo, una vez que el espejo esté en su lugar, es permanente. cinta adhesiva de doble faz F G 5.
INSTRUCCIONES DE ENSAMBLAJE 6. Coloque la tapa de extremo grande (CC) en el tubo cónico corto (E). 6 ensamble del tubo inferior Coloque el extremo cónico del tubo cónico pequeño (E) en el extremo no cónico del ensamble del tubo inferior, como se muestra. extremo cónico en la parte superior E Aditamentos utilizados CC x1 Tapa de extremo grande 7. N OTA: ESTE ENSAMBLAJE SE MUESTRA PARA UNA ALTURA DE ABERTURA DE 243,84 CM.
INSTRUCCIONES DE ENSAMBLAJE 8. Coloque tapa de extremo pequeña (BB) en el tubo de 3/4 pulg. 8 BB A Inserte el anillo de transición (EE) en el tubo recto (B). Deslice el tubo de 3/4 pulg. (A) a través del anillo de transición (EE) y dentro del tubo recto (B), como se muestra. EE A Coloque las tiras de cinta (GG) alrededor de las uniones de los tubos. NOTA: después de insertar el tubo de 3/4 pulg.
INSTRUCCIONES DE ENSAMBLAJE 10. Instale la jabonera (I) en cualquier estante (F). Las lengüetas en el fondo de la jabonera (I) se encajan en los orificios de los estantes (F). 10 I NOTA: la jabonera se puede insertar en varios lugares de cada estante según su preferencia. (Una vez instalada, la jabonera se puede retirar presionando firmemente hacia adentro y hacia arriba en las lengüetas de debajo del estante). F CUIDADO Y MANTENIMIENTO La limpieza con un paño seco puede ser suficiente.