Installation Guide

Fabric roll
Bracket A / Bracket B
4
Insert pins on each side of the hem. Attach the grip to the center of the hem.
Install bottom hem pins
USE AND CARE GUIDE
ROLLER SHADE WITH
CORDLESS CLUTCH SYSTEM
PACKAGE CONTENTS
Part QuantityDescription
A/B
K
C
D
E
D
B
J J
A
B
K
H
A
F
G
1/1
1
1
4
4
1
Screws
H
1
Anchors
I
1
Temporary endcap
J
2
Grip
Re-tensioning crank
K
1
Hem pins
Plastic hem slat
Pin-end plug
Questions, problems, missing parts? Before returning to the store,
call StyleWell Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 7 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
THANK YOU
We appreciate the trust and confidence you have placed in StyleWell
through the purchase of this ROLLER SHADE WITH CORDLESS CLUTCH
SYSTEM. We strive to continually create quality products designed to
enhance your home. Visit us online to see our full line of products available
for your home improvement needs. Thank you for choosing StyleWell!
TOOLS REQUIRED
Safety Information
Care and Cleaning
Pre-Installation
INSTALLATION
Troubleshooting
You may clean your Shade using a mild soap solution. Brush lightly with a soft
cloth. Let the Shade dry before rolling it up.
NOTICE: This Shade can be resized in store. Determine the space to be occupied
by the Shade with brackets, and ask a store associate to cut it if necessary.
WARNING: Product failure due to using incorrect fixings is
responsibility of the installer. In case of doubt on what anchor to use,
please consult with a professional. For surfaces such as metal or
concrete, please purchase appropriate screws and hardware.
1
Trim any loose threads from the Shade with scissors if necessary. Remove
temporary end cap from hex end of Shade and insert pin end plug on the
opposite end. Slide plastic slat through the hem.
Tape Measure Level
Philips-head
screwdriver
Drill & Bit SetPencil
Assemble the Shade
2
Decide to mount your Shade INSIDE or OUTSIDE window frame. Mark bracket B
location on your left and install it. Insert hex-end of the Shade into bracket B.
Then position bracket A so the Shade is leveled and centered. Use a level if
needed. Mark bracket A location. Remove the Shade and install bracket A.
Proceed to Step 3.
Bracket installation
3
Insert hex end of Shade into bracket B. Rotate the Shade for a tight fit if necessary.
Drop the pin-end into bracket A with open latch. Close the latch on bracket by slowly
pressing down on it until it clicks into place.
Install the Shade
CAUTION: Before placing the shade into the brackets make sure the
fabric is rolled up evenly.
CAUTION: Bracket installation on WOOD: Pre-drill pilot holes with
3/32 in. bit. Secure the brackets with screws provided.
Bracket installation on DRYWALL OR PLASTER: Pre-drill pilot holes with
3/16 in. bit. Insert the anchors into the holes and secure the brackets
with screws provided.
Close
Problem Solution
The Shade rolls
up to slowly.
The Shade rolls
up too quickly.
The Shade lost its
tension entirely.
Increase the tension by rotating the adjusting knob towards yourself.
Alternatively, you can also tighten the tension by:
1. Pull down one foot so that the shade is locked in place
2. Remove Shade from brackets
3. Roll shade up all the way
4. Re-install on brackets
Soften the tension by rotating the adjusting knob in the direction
towards the window. Alternatively, you can also reduce the tension by:
1. Remove shade from brackets
2. Unroll shade down an additional foot
3. Re-install on brackets
The shade can be re-tensioned using the crank provided. Rotate
clockwise the number of cycles outlined below, then half a cycle
counterclockwise to lock tension in place.
1. For <37 ¼” width: 12 cycles.
2. For >37 ¼” but <55 ¼” width: 18 cycles.
3. For >55 ¼” but <73 ¼” width: 28 cycles.
A B C GH I
E
F J
3/16”
DRYWALL
3/32”
WOOD OR STUDS
OUTSIDE MOUNT INSIDE MOUNT
G