INSTALLATION GUIDE Wine Storage
Contents Important Note Wine Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of highlighted information throughout this guide: Models 424G and 424FSG Installation . . . . . . . . . . . . . . . 4 Models 427G and 427RG Installation . . . . . . . . . . . . . . . 16 Model WS-30 Installation . . . . . . . . . . . . . . . . . . . . . . . . 30 Installation Checklist . . .
Wine Storage 3 subzero.com Sub-Zero Wine Storage The importance of the installation of the Sub-Zero wine storage unit cannot be overemphasized. Installation should be done by a qualified installer. RATING PLATE Before you begin the installation process, it is recommended that you read this entire installation guide. There are key details that you should take special care to observe during the installation.
Models 424G and 424FSG Installation 4 Models 424G and 424FS OVERALL DIMENSIONS 23 7/8" (606) 24" (610) 24 1/4" (616) 24 5/8" (625) 34" 34 3/16" (864) (868) 4" (102) 4" (102) 25 3/8" 25 3/8" (645) (645) 2 3/8" (60) MODEL 424G Door swing clearances are based on stainless steel door and handle dimensions.
Models 424G and 424FSG Installation 5 subzero.com Models 424G and 424FSG Installation The model 424FSG wine storage unit is designed to be attractive in a stand alone setting. Model 424G must be built in. Refer to the previous page for overall dimensions and door swing clearances for models 424G and 424FS. OPENING DIMENSIONS TOP VIEW 24" (610) OPENING DEPTH Make sure that the finished rough opening where the model 424G wine storage unit is to be installed is properly prepared.
Models 424G and 424FSG Installation 6 Electrical Requirements For models 424G and 424FSG, the electrical supply should be located within the shaded area shown in the illustration. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Models 424G and 424FSG Installation 7 subzero.com Electrical Requirements Moving the Unit HOME ALARM SYSTEM Before moving the wine storage unit into position, make sure all opening dimensions and electrical requirements are complete and accurate. If a home alarm system is to be used, refer to home alarm connections on page 11. In addition to operating power, the installer may also be required to supply a home automation system lead to the unit.
Models 424G and 424FSG Installation 8 Anti-Tip Bracket Installation MODEL 424FSG To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with the anti-tip bracket. An anti-tip bracket and hardware is provided with the wine storage unit. The anti-tip bracket must be installed on a solid base to prevent tipover in case several loaded wine shelves are extended at the same time.
Models 424G and 424FSG Installation 9 subzero.com Anti-Tip Bracket Installation MODEL 424FSG—WOOD FLOORS INSTALL CONCRETE WEDGE ANCHORS: Use the four #12 x 21 /2" wood screws and the four 1/4" flat washers provided. Drill pilot holes 3/16" (5) diameter maximum, and be sure that the screws penetrate through the flooring material and into the wall plate a minimum of 3/4" (19). Be sure that the screws hold tight. Refer to the illustration below.
Models 424G and 424FSG Installation 10 Position the Unit If you are adding an accessory lock kit to your wine storage unit, it should be installed before you position the unit. The accessory lock kit and additional instructions are available through your authorized Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com.
Models 424G and 424FSG Installation 11 subzero.com Level the Unit Home Alarm Connections Using an adjustable wrench or pliers, turn each of the four leveling legs clockwise to raise the unit and counterclockwise to lower the unit. Refer to the illustration below for location of the leveling legs. Before the kickplate is installed, all necessary wiring connections in the compressor compartment should be completed. For model 424G, the countertop bracket should be used to make a solid installation.
Models 424G and 424FSG Installation 12 Kickplate Installation Door Panel Once the unit is leveled and wiring connections made, the kickplate can be installed. Use the two #10 x 1/2" stainless steel screws that are provided with the kickplate. Refer to the illustration below. MODEL 424G IMPORTANT NOTE: The kickplate must be removed for servicing. The floor cannot interfere with removal. The louvered section of the kickplate must not be covered so as to prevent air circulation.
Models 424G and 424FSG Installation 13 subzero.com Overlay Door Panel MODEL 424G Inspect the door panel for the minimum 5/8" (16) thickness, the finished inside edge. The glass door has a 10 lbs (5 kg) The door panel is then lowered from the door frame, tenon centers removed, the door opened and the screws driven into the panel through the black tape on the door frame, using the center marks to locate the screws. weight limit.
Models 424G and 424FSG Installation 14 Overlay Door Panel IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door. After the door panel installation is complete, apply the cover patches or plugs provided over the holes on the inside surface of the door. The cover patches or plugs are part of the insulation system on the door of the wine storage unit.
Models 424G and 424FSG Installation 15 subzero.com Hinge Adjustment Complete the Installation IMPORTANT NOTE: The wine storage unit must be installed and leveled before door hinge adjustments can be made. When you have completed installation of the model 424G or 424FSG wine storage unit, refer to page 54 for an installation checklist and page 55 for service information.
Models 427G and 427RG Installation 16 Models 427G and 427R OVERALL DIMENSIONS 27" (686) 24" (610) 27" (686) 14" (356) 24" (610) 14" (356) 13/16" (21) 13/16" (21) 78 9/16" 78 9/16" (1995) (1995) 80" 80" (2032) OPENING HEIGHT (2032) OPENING HEIGHT 3/8" (10) 1/2" (13) 13 1/4" (337) 10 1/4" 34 1/2" (876) (260) 20 3/8" (518) 8 15/16" 9 3/4" (227) (248) 4" HEIGHT DIMENSIONS ± 1/2" (13) 4" HEIGHT DIMENSIONS ± 1/2" (13) (102) 24" 24" (610) (610) (102) 4 5/8" 4 5/8" (117) (11
Models 427G and 427RG Installation 17 subzero.com Models 427G and 427RG Installation Make sure that the finished rough opening where the wine storage unit is to be installed is properly prepared. Refer to the opening dimensions illustrations for models 427G and 427R on the previous page. OPENING DIMENSIONS TOP VIEW 25" (635) OPENING DEPTH IMPORTANT NOTE: The floor under the wine storage unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing.
Models 427G and 427RG Installation 18 Electrical Requirements For models 427G and 427RG, the electrical supply should be located within the shaded area shown in the illustration below. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Models 427G and 427RG Installation 19 subzero.com Electrical Requirements Anti-Tip Bracket Installation HOME ALARM SYSTEM If a home alarm system is to be used, refer to wiring connections on page 24. In addition to operating power, the installer may also be required to supply a home automation system lead to the unit. This is for a lowvoltage, low-current signal similar to door and window sensor signals. Common, normally open and normally closed contact configurations are provided.
Models 427G and 427RG Installation 20 Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: Use the six #12 x 2 1/2" wood screws and the six 1/4" flat washers provided. Drill pilot holes 3/16" (5) diameter maximum, and make sure the screws penetrate through the flooring material and into the wall plate a minimum of 3/4" (19). Make sure the screws hold tight. Refer to the illustration below. 1) Drill a 3/8" (10) diameter hole any depth exceeding the minimum embedment.
Models 427G and 427RG Installation 21 subzero.com Unpack the Unit DUAL INSTALLATIONS Before moving the wine storage unit into position, secure the door closed, remove drawers (427RG) and protect any finished flooring. Uncrate the wine storage unit and inspect for any damage. Remove the wood base and discard the shipping bolts that hold the wood base to the bottom of the unit. Remove all packing materials and tape.
Models 427G and 427RG Installation 22 Position the Unit Retract the front leveling legs all the way up to allow the unit to be moved into position more easily. You will extend the leveling legs when the unit is in its final position to reduce the possibility of the unit tipping forward. Slide the unit into position, making sure the anti-tip bracket is engaged properly. Extend the front leveling legs down approximately 3/16" (5) to make additional adjustments easier.
Models 427G and 427RG Installation 23 subzero.com Level the Unit Molding Installation Level the wine storage unit by turning the front leveling legs clockwise to raise or counterclockwise to lower the unit. To assist you in adjusting the front leveling legs up or down, use a standard screwdriver blade and place it in the front leveling leg as shown in the illustration below. Install the decorative white molding strips to the top and sides of models 427G and 427RG for a finished look.
Models 427G and 427RG Installation 24 Wiring Connections Before the kickplate/grille is installed, all necessary wiring connections in the compressor compartment should be completed. If the dual installation heater kit is used with model 427G or 427RG, the power supply leads should be connected according to instructions included with the kit. If a home alarm system is to be installed on the wine storage unit, the connections should be made using the logic supplied with the alarm specifications.
Models 427G and 427RG Installation 25 subzero.com Kickplate/Grille Installation Door Panels Once the wine storage unit is leveled and wiring connections made, the kickplate/grille can be installed. The mounting bracket may be adjusted slightly forward or back so the kickplate/grille will fit flush with the surrounding area. Refer to the illustration below. Models 427G and 427RG have a full-view glass door.
Models 427G and 427RG Installation 26 Stainless Steel Door Panel Overlay Door Panel Before installing the stainless steel door panel, check the panel carefully. Options are available for kickplate/grille height, overall height, door swing and door lock. Inspect the door panel for the minimum 5/8" (16) thickness, the greater width requirements for the stiles (to cover the door hinges), and the finished inside edge. The glass door panel has a weight limit of 20 lbs (9 kg).
Models 427G and 427RG Installation 27 subzero.com Overlay Door Panel The screw holes inside the door are hidden under a cover flap on the door gasket. It is necessary to lift the flap to insert the screws. Use as many screws as necessary to hold the door panel in place properly. IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door.
Models 427G and 427RG Installation 28 Drawer Panel Installation MODEL 427RG IMPORTANT NOTE: Drawer panels for model 427RG must be a minimum of 5/8" (16) thick and cannot exceed 12 lbs (5 kg) for each panel. Remove the mounting hardware provided and set aside. As with the door panel, you should work on the back side of each drawer panel to protect the front surface. Position the top edge of the template flush with the top edge of each drawer.
Models 427G and 427RG Installation 29 subzero.com Side Panels Side panels for models 427G and 427RG are not attached to the unit. You must securely fasten the panels to the adjacent cabinets and floor. Panels should be fastened to the floor and walls using L-brackets (hardware not provided). To help you move the unit into place, rout out an area in the floor so the L-bracket will sit flush with the floor level. OPTIONAL 90° DOOR STOP The door of models 427G and 427RG opens to 105°.
Model WS-30 Installation 30 Model WS-30 Make sure that the actual equipment that was shipped to you matches the design you are expecting to install. Before you begin the installation process, check the exact model number you need against the model number on the shipping carton. If the unit you receive does not match your requirements, contact your authorized Sub-Zero dealer.
Model WS-30 Installation 31 subzero.com Site Preparation Make sure that the finished rough opening where the wine storage unit is being installed is properly prepared. Refer to installation specifications on the following pages. These specifications are identical for the framed, overlay and stainless steel applications. Installation specifications are different for the flush inset application, whether you are using custom panels or Sub-Zero accessory flush inset panels.
Model WS-30 Installation 32 Standard Installation Opening Dimensions Framed, Overlay and Stainless Steel Models TOP VIEW 24" (610) OPENING DEPTH 24" (610) OPENING DEPTH SIDE VIEW 83 3/4" (2127) OPENING HEIGHT 29 1/2" (746) OPENING WIDTH FRONT VIEW IMPORTANT NOTE: If two units are installed side by side, refer to page 34 for dual standard installations. Stainless steel models are ready to install out of the box.
Model WS-30 Installation 33 subzero.
Model WS-30 Installation 34 Dual Standard Installation Opening Dimensions Framed, Overlay and Stainless Steel Models TOP VIEW 24" (610) OPENING DEPTH 24" (610) OPENING DEPTH 83 3/4" A (2127) OPENING HEIGHT OPENING WIDTH SIDE VIEW FRONT VIEW Opening Widths A Two 30" (762) Models 59 3/4" Model WS-30 and a 36" (914) Model 65 3/4" (1670) (1518) IMPORTANT NOTE: A dual installation kit will be required for this installation. Stainless steel models are ready to install out of the box.
Model WS-30 Installation 35 subzero.
Model WS-30 Installation 36 Electrical Requirements For model WS-30, the electrical supply should be located within the shaded area shown in the illustration. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Model WS-30 Installation 37 subzero.com Anti-Tip Bracket Installation To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with the anti-tip brackets provided. IMPORTANT NOTE: Placement of the anti-tip brackets is critical to a stable installation. Failure to properly position the anti-tip brackets will prevent them from engaging the unit.
Model WS-30 Installation 38 Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: After properly locating the anti-tip brackets in the rough opening, drill pilot holes 3/16" (5) diameter maximum in the wall studs and/or wall plate. Use the #12 x 2 1/2" PH pan HD zinc screws and #12 flat washers to secure the brackets in place. Make sure the screws penetrate through the flooring material and into wall studs or wall plate a minimum of 3/4" (19).
Model WS-30 Installation 39 subzero.com Unpack the Unit Grille Removal Uncrate the wine storage unit and inspect for any damages. Remove the wood base and discard the shipping bolts and brackets that hold the wood base to the bottom of the unit. Remove and discard all packing materials. In order to prevent damage to the grille and to access the power cord, the top grille assembly should be removed prior to moving the unit. IMPORTANT NOTE: Do not discard the kickplate, anti-tip brackets and hardware.
Model WS-30 Installation Position the Unit Before moving model WS-30 into position, secure the door closed and protect any finished flooring. Use an appliance dolly to move the unit near the rough opening. Model WS-30 is equipped with rollers, so it can be moved into position more easily. If possible, keep the door closed until the unit is properly anchored.
Model WS-30 Installation 41 subzero.com Door Adjustment The door of the model WS-30 can be adjusted in three ways: In and out, side to side tilt, and up and down. Regardless of the adjustment being made, start by slightly loosening the two upper hinge bolts on the upper hinge plate using a 1/2" wrench. Refer to the illustration below. DOOR HEIGHT ADJUSTMENT To adjust a left-hinge door; using a 1/4" allen wrench, turn the bolt clockwise to raise the door and counterclockwise to lower the door.
Model WS-30 Installation 42 Panel Installation Complete the Installation If your customer has ordered either a framed or overlay model, you will be installing a door panel to give the unit the custom Sub-Zero look. Before you begin installing the panel, refer to the panel specifications for framed, overlay or flush inset applications on pages 44–52, and make sure you are working with the panel design called for in your installation.
Model WS-30 Installation 43 subzero.com Complete the Installation Home Alarm Connections INSTALL KICKPLATE If a home alarm system is to be installed on the wine storage unit, the connections should be made according to the alarm specifications. Refer to the illustration for the appliance lead locations, and refer to the following for color codes: Make sure the drain pan is in the proper position before installing the kickplate.
Model WS-30 Installation 44 Framed Panel If your customer has chosen a framed design application, make sure that the panel you are about to install matches dimensions listed in the framed panel specifications on the following page. Additional panel design information can be found in the Sub-Zero design guide and on our website, subzero.com. If the thickness of the custom panel is less than a 1/4" (6), back it up with a sheet of shim material to build the total thickness to a 1/4" (6).
Model WS-30 Installation 45 subzero.com Framed Panel Framed Panel Specifications RAISED PANEL With some door panel designs, you may have to rout, recess or use optional extended handles to allow for finger clearance. This is particularly true if your unit has raised panels greater than 1/4" (6) total thickness. Check the location of offset when you’re using specific routing for the grip area only. Refer to the Sub-Zero design guide for a full-scale template of the standard full-length handle and panel.
Model WS-30 Installation 46 Overlay Panels If your customer has chosen an overlay design application, make sure that the panels you are about to install match dimensions listed in the overlay panel specifications on the following page. Additional panel design information can be found in the Sub-Zero design guide and on our website, subzero.com. IMPORTANT NOTE: The size of the overlay panel is critical. It must fit over the door frame.
Model WS-30 Installation 47 subzero.com Overlay Panels Overlay Panel Specifications GRILLE PANEL ASSEMBLY Remove the grille panel assembly as described on page 39. Remove the top two corner screws and pull away the top frame. Slide the panel into position in the grille frame. If you are using a grille panel 1/4" (6) or thinner, you will need to install a filler. Reattach the top frame by reinstalling the two top corner screws.
Model WS-30 Installation 48 Flush Inset Panels If your customer has chosen the flush inset panel application, make sure that the panels you are about to install match dimensions listed in the flush inset panel specifications on the following page. Additional panel design information can be found in the Sub-Zero design guide and on our website, subzero.com. IMPORTANT NOTE: The size of the flush inset panel is critical. It must fit over the door frame.
Model WS-30 Installation 49 subzero.com Flush Inset Panels Remove the grille panel assembly as described on page 39. Remove the top two corner screws and pull away the top frame. Slide the panel into position in the grille frame. If you are using a grille panel 1/4" (6) or thinner, you will need to install a filler. Flush Inset Panel Specifications H A A A H Reattach the top frame by reinstalling the two top corner screws.
Model WS-30 Installation 50 Flush Inset Panel Dual Installations Illustrations A–D provide panel offsets and reveals for model WS-30 in a flush inset application. Refer to the chart below for reference to the illustrations. When two models WS-30 or a model WS-30 and built-in unit are installed side by side, a dual installation kit may be required. Contact your authorized Sub-Zero dealer for the proper components and installation instructions.
Model WS-30 Installation 51 subzero.com Dual Installations Flush Inset Panels—Dual Installation DUAL FLUSH INSET INSTALLATIONS Installing two models WS-30 or a model WS-30 and built-in unit side by side in a flush inset application will require adjustments to the dimensions of your finished rough opening, panel sizes and panel offsets. It will also require a dual installation kit, available through your authorized Sub-Zero dealer.
Model WS-30 Installation 52 Flush Inset Panels—Dual Installation When installing two models WS-30 or a model WS-30 and built-in unit side by side in a flush inset application, you must decrease the width of the decorative flush inset panels by 1/2" (13). Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing.
Model WS-30 Installation 53 subzero.com Side Panels IMPORTANT NOTE: Side panels will need to be installed before the unit is placed in its final position. When installing a model WS-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through your authorized Sub-Zero dealer. Refer to instructions included with the side panel kit when installing these side panels.
Installation Checklist Installation Checklist To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Have all packing materials been removed? Turn the unit on.
Service Information 55 subzero.com Service Information If service is necessary, maintain the quality built into your wine storage unit by calling Sub-Zero factory certified service. For the name and number of Sub-Zero factory certified service nearest you, check the contact & support section of our website, subzero.com or call Sub-Zero customer care at 800-222-7820. If you are storing or disposing of your old refrigerator or freezer, please do it safely.
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 7022655 REV-A 3/ 2011 SUBZERO.COM 800.222.
