User Guide

ManualsBrandsSub-Zero ManualsOther611G-PS

With the installation of a harness kit, these

appliances are Star-K compliant to meet strict

religious regulations in conjunction with specific

instructions f

ound on star-k.org. You may purchase

this harness kit thr

ough y

our Sub-Zero dealer.

o obtain local dealer inf

ormation, visit the Locator

section of our website, subzero.com.

Planning Information

Built-In Model 611G

Over-and-Under Refrigerator/ Freezer with Glass Door

Dimensions in parentheses are in

millimeters unless otherwise specified.

11/06

The Sub-Zero Model 611G over-and-

under refrigerator/freezer with glass door

is available in your choice of the framed,

overlay or stainless steel design application.

Three stainless steel finishes are offered—

classic (/S), platinum (/P) and carbon (/B).

Many people are gravitating toward a commercial

looking kitchen but they lac

k the refriger

ation unit that

allows them to achieve that look. The Model 611G with

a glass door along with its cousin, the Model 650G, are

the only over-and-under refrigerator / freezer models on

the market that allow you to do that for your clients

and they are manufactured by Sub-Zero. Need we say

more?

riple-pane

V resistant low-

nergy glass door

Four-sided

magnetic gaskets

Door closers

Removable kickplate

High humidity

risper drawer

Adjustable spill-proof

lass shelves

ighted electronic

ontrol panel

Hermetically sealed

efrigeration units

Front venting allows

nit to be completely

uilt in

erial and model

number plate

Automatic ice maker

Two-tier wire

storage baskets

Full-extension roll-out

freezer drawer

gg container

Model 611G/S (P/B)

Stainless Steel

Model 611G/O

Overlay

odel 611G/F

ramed

(Stainless steel design shown)

Summary of content (15 pages)

PAGE 1
Planning Information Built-In Model 611G Over-and-Under Refrigerator / Freezer with Glass Door Front venting allows unit to be completely built in Hermetically sealed refrigeration units Serial and model number plate Lighted electronic control panel Triple-pane UV resistant lowenergy glass door Adjustable spill-proof glass shelves Model 611G/F Framed Egg container High humidity crisper drawer Four-sided magnetic gaskets Automatic ice maker Model 611G/O Overlay Two-tier wire storage baskets Door
PAGE 2
Planning Information Built-In Model 611G F E AT U R E S 30" (762) over-and-under refrigerator / freezer with glass door Door alarm will let you know with an audible beeping if your refrigerator door or freezer drawer are left ajar Framed, overlay and stainless steel applications provide complete design flexibility Automatic ice maker provides an ample supply of crescent-shaped ice Sub-Zero's dual refrigeration system ensures the freshest food and energy efficiency Triple-pane UV-resistant low-energy
PAGE 3
Planning Information Built-In Model 611G S P E C I F I C AT I O N S Model 611G MODEL OPTIONS Framed Design 611G/F Overlay Design 611G/O Classic Stainless Steel 611G/S Platinum Stainless Steel 611G/P Carbon Stainless Steel 611G/B You must allow 90 days from order to delivery for platinum and carbon finishes. Over-and-Under Refrigerator / Freezer with Glass Door Overall Width 30" (762) Overall Height 84" (2134) Overall Depth 24" (610) Refrigerator Capacity 12.
PAGE 4
Planning Information Built-In Model 611G I N S TA L L AT I O N S P E C I F I C AT I O N S 24" EXTEND WATER LINE APPROX.
PAGE 5
Planning Information Built-In Model 611G I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. Allow the door to open a minimum of 90˚ or you'll have problems removing drawers. With the door opening at 90˚, you may have to move drawers slightly to clear the door interior. Refer to the minimum door swing clearance in the specifications chart.
PAGE 6
Planning Information Built-In Model 611G A D D I N G PA N E L S F R A M E D PA N E L S PANELS 1/4" (6) THICK OR LESS Trim reveal 1/4" (6) min 1/4" (6) Panel In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. You will not have to install front door panels.
PAGE 7
Planning Information Built-In Model 611G 1 F R A M E D PA N E L S The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. H C C C 14" (356) H An 11" (279) louvered grille is standard on framed applications. Optional louvered grilles are available in 1" (25) height increments from 10" (254) to 15"(381).
PAGE 8
Planning Information Built-In Model 611G O V E R L AY PA N E L S O V E R L AY PA N E L S The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels—the decorative overlay panel, a .10" (3) spacer panel and a 1/4" (6) backer panel.
PAGE 9
Planning Information Built-In Model 611G O V E R L AY PA N E L S The refrigerator door panel must include a cut-out to accommodate the window. Refer to the chart below for exact dimensions. The glass portion of the door must be exposed and not covered by any part of the panel. H An 11" (279) panel grille is standard on overlay applications. Optional panel grilles are available in 1" (25) height increments from 10" (254) to 15" (381).
PAGE 10
Planning Information Built-In Model 611G O V E R L AY PA N E L S IMPORTANT NOTE: For overlay door panels, it is necessary to rout a space for the unit‘s lower hinge plate so that it does not strike the door panel. Refer to the top illustration on this page. You will minimize the reveal between the bottom of the overlay door panel and the top of the overlay drawer panel. Refer to the bottom illustration on this page.
PAGE 11
Planning Information Built-In Model 611G S I D E PA N E L S Side panels can be used with the framed, overlay and stainless steel design applications. When planning for side panels with the installation of the Built-In model, you need to be aware of space configuration to achieve a pleasing fit. Depending on the exact panel you are using with your unit, the height of the panel will vary.
PAGE 12
Planning Information Built-In Model 611G H A N D L E P R O F I L E – F R A M E D A P P L I C AT I O N OPTIONAL EXTENDED FULL-LENGTH HANDLE 1" 2" 3" (25) (51) (76) 11/4"(32) PANEL STANDARD FULL-LENGTH HANDLE 1"(25) PANEL 3/4"(19) PANEL 1/2"(13) PANEL 1/4"(6) PANEL 1/4"(6) FRAMED PANEL DOOR F U L L - S C A L E T E M P L AT E S HANDLE PROFILE The following full-scale illustrations enable you to understand some of the unique situations you may face as you design the Built-In units into homes.
PAGE 13
Planning Information Built-In Model 611G H A N D L E P R O F I L E – S T A I N L E S S S T E E L / O V E R L AY A P P L I C A T I O N S STANDARD STAINLESS STEEL HANDLE 1" 2" 3" (51) (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 5/8" (16) PANEL 1/2" (13) PANEL 1/4" (6) PANEL 1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.
PAGE 14
Planning Information Built-In Model 611G PA N E L A N D H A N D L E P R O F I L E – 1 3 0 ˚ D O O R O P E N I N G 130˚ DOOR OPENING WITH 2" (51) FILLER STRIP SUB-ZERO UNIT SUB-ZERO UNIT (TOP VIEW) FILLER STRIP 2" (51) ALLOW FOR FILLER LAP BEHIND FLANGE DOOR CLOSED OVERLAY PANEL 3/4" (19) THICK (NOMINAL) MAIN FRAME HINGE )P AN 3) *1 /4" 1 (6 /2" (1 3 DOOR OPEN @ 130˚ EL 9) (1 /4" PA NE L (2 PA N EL PA N 5) (3 1" 11 /4" EL PA N EL STANDARD FRAMED FULL-LENGTH HANDLE 2) APPR
PAGE 15
Planning Information Built-In Model 611G O V E R L AY PA N E L A P P L I C A T I O N – 9 0 ˚ D O O R O P E N I N G 90˚ DOOR OPENING (TOP VIEW) NOMINAL OVERALL WIDTH OF SUB-ZERO SUB-ZERO UNIT 237/8" (606) TO REAR OF SUB-ZERO MAIN FRAME 0" (0) 1/4" (6) DOOR CLOSED 1/2" (25) 3/4" (19) HINGE 1" (25) 11/4" (32) 11/2" (38) 13/4" (44) 2" (51) 21/4" (57) 21/2" (63) DOOR OPEN @ 90˚ 23/4" (70) 3" (76) 31/4" (83) *1/4" (6) PANEL 1/2" (13) PANEL 3/4" (19) PANEL 1" (25) PANEL 11/4" (32) PANEL 31/2" (8