Installation Instructions

ManualsBrandsSub-Zero ManualsStove & Range AccessoriesSub-Zero E Series Contemporary Warming Drawer Handle

802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395

Warming Drawer Handle Installation Instructions

812548 / Rev D / October, 2011Page 1 of 4

CONT

AINS:

ITEM

QTY DESCRIPTION

A 4 Bolt, #10-24 x 3/4''

B 4 Bolt, #10-24 x 1''

C 4 Bolt, #10-24 x 1-1/4''

D 4 Bolt, #10-24 x 1-3/4''

E 4 Bolt, #10-24 x 2-1/4''

F 4 Bolt, #8-32 x 5/8''

G 4 Bolt, #8-32 x 1''

NOTES:

• This front panel kit is designed for and approved only for use with Wolf Warming Drawer (WWD30).

• These handle kits are designed for use with a Wolf Integrated Front Panel Kit #808152

• Please read these instructions carefully before beginning installation.

• For any additional information, refer to the Use and Care Information and Installation instructions included

with model WWD30.

AB C D EFGHI JK L

Fastener Reference

802781 Handle, Tubular 23-1/2” Classic

802782 Handle, Tubular 23-1/2” Carbon

802783 Handle, Tubular 23-1/2” Platinum

812340 Handle Curved 26-7/8” Framed

812341 Handle, Curved 29-3/8” Unframed

812342 Handle, Pro 25-7/8”

814020 Tube Handle, 3/4'' Unframed

815837 Tube Handle, 3/4'' Framed

820395 Tube Handle, 3/4'' Black

ITEM QTY DESCRIPTION

H 4 Bolt, #8-32 x 1 1/4''

I 4 Bolt, #8-32 x 1 3/4''

J 4 Bolt, #8-32 x 2 1/2''

K 4 Washer, 1/4 x 5/8''

L 2 Stud, Mounting

1 Instructions

See Fastener Reference Diagram Below:

Summary of content (4 pages)

PAGE 1
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395 Warming Drawer Handle Installation Instructions 802781 802782 802783 812340 812341 Handle, Tubular 23-1/2” Classic Handle, Tubular 23-1/2” Carbon Handle, Tubular 23-1/2” Platinum Handle Curved 26-7/8” Framed Handle, Curved 29-3/8” Unframed 812342 814020 815837 820395 Handle, Pro 25-7/8” Tube Handle, 3/4'' Unframed Tube Handle, 3/4'' Framed Tube Handle, 3/4'' Black NOTES: • • • • This front panel kit is designed for and approved only
PAGE 2
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395 Warming Drawer Handle Installation Instructions INSTALLATION PROCEDURE: 1” Tubular Handles (Kits 802781, 802782, 802783): 1. Mark custom panel to locate the drill holes using the center-line dimensions from Figure 1. Drill four (4) 7/32'' to 1/4'' holes. 2. Counter bore 5/8'' holes to 5/32'' deep so that you can completely recess the head of the bolt and washer (See Figure 2). 3.
PAGE 3
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395 Warming Drawer Handle Installation Instructions 2. The panel should be counter bored so that when an appropriate length bolt and washer are put in the hole, between 1-3/8'' to 1-3/4'' of thread is exposed on the face side of panel to hold the handle (See Figure 4). 3. Be sure that there is enough material removed with the counter bore that the bolt head surface is completely recessed into the cabinet panel (See Figure 4). 4.
PAGE 4
802781, 802782, 802783, 812340, 812341, 812342, 814020, 815837, 820395 Warming Drawer Handle Installation Instructions Curved Handles Framed & Unframed (Kits 812340, 812341): 1. Mark custom panel to locate the drill holes using the center-line dimensions from Figures 7 or 9. Drill four (4) 7/32'' to 1/4'' holes. NOTE: Countersink procedure is critical for this application. Damage may occur to the handle if these instructions are not followed precisely. 2.