Installation Instructions

ManualsBrandsSub-Zero ManualsAccessoriesDual Install Kit with 72" Pro Louvered Grille

7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624

(Instructions for Dual Grille Kits Listed Above)

7010064 / Rev C / March, 2011

NOTES:

• The production grille assemblies MUST

be removed before beginning.

• The dual installation heater assembly and the center trim piece MUST be attached to the right side of the

unit that will be installed at the left side of the rough-in opening.

• The main frame shim MUST

be attached to the left side of the unit that will be installed at the right side of

the rough-in opening.

BI SERIES UNITS ARE HEAVY AND CAN BE UNSTABLE WHEN ATTEMPTING TO INSTALL THEM. WHEN

MOVING A BI SERIES UNIT KEEP THE DOORS AND DRAWERS TAPED CLOSED. THE ANTI-TIP COMPO-

NENTS SUPPLIED WITH BI SERIES UNITS MUST BE UTILIZED AS SPECIFIED IN THE INSTALLATION

MANUAL. THE FRONT LEVELING LEGS OF A BI SERIES UNIT MUST BE EXTENDED TO THE FLOOR TO

COMPLETE THE INSTALLATION. IF A BI SERIES UNIT WERE TO TIP AND FALL IT COULD CAUSE SERI-

OUS INJURY OR DEATH!

Page 1 of 7

CONTAINS:

QTY

DESCRIPTION

2 Spacer, 1/8" X .204 Id

2 Bolt, #10-24 X 1/2" Roundhead

4 Bolt, Tensilock 5/16-18 X 3/4

1 Clip, Cord Plastic 5/16 X 1/2

6 Screw, #8-32 X 1/2 Pan Hd

1 Screw, #10-12 X 1-1/4 Truss Hd

9 Screw, 10-12 X 3/4, 6-Lobe Ph

1 Nut, Dual #10-24 X 1 (7001272)

4 Threaded Insert,5/16-18 Hx Opn

1 Trim, Dual Install Center Short

1 Grille, Dual Framed 60-1/4 (7004808 Kit Only)

1 Grille, Dual Framed 72-1/4 (7004809 Kit Only)

1 Grille, Dual Overlay 60-1/4 (7004810 Kit Only)

1 Grille, Dual Overlay 66-1/4 (7012623 Kit Only)

1 Grille, Dual Overlay 72-1/4 (7004811 Kit Only)

1 Grille, Dual SS 60-1/4 (7004812 Kit Only)

1 Grille, Dual SS 66-1/4 (7012624 Kit Only)

1 Grille, Dual SS 72-1/4 (7004813 Kit Only)

QTY DESCRIPTION

1 Bracket, Dual Install Bottom

1 Bracket, Dual Grill Support

1 Bracket, Dual Grill Slide

4 Screw, 5/16 X 3/4 Thread-Forming

1 Instructions,Dual Grill Kits

1 Kickplt, Blk 59.25 (7004808 & 7004810 Kits Only)

1 Kickplt, Black 65.5 (7012623 Kit Only)

1 Kickplt, Blk 71.75 (7004809 & 7004811 Kits Only)

1 Kickplate, Stainless 59.7 (7004812 Kit Only)

1 Kickplate, Stainless 65.5 (7012624 Kit Only)

1 Kickplate, Stainless 71.7 (7004813 Kit Only)

1 Bracket, Dual Install Top

3 Bracket Assy,Dual Trim

1 Threaded Insert,Install Tool

1 Heater Assy, Dual Installation

1 Shim, Assy Main Frame

1 Bracket Assy, Magnet Center

2 Bracket Assy, Magnet Side

6 Nut, 10-24 Hex Flange Lock

Summary of content (7 pages)

PAGE 1
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) BI SERIES UNITS ARE HEAVY AND CAN BE UNSTABLE WHEN ATTEMPTING TO INSTALL THEM. WHEN MOVING A BI SERIES UNIT KEEP THE DOORS AND DRAWERS TAPED CLOSED. THE ANTI-TIP COMPONENTS SUPPLIED WITH BI SERIES UNITS MUST BE UTILIZED AS SPECIFIED IN THE INSTALLATION MANUAL. THE FRONT LEVELING LEGS OF A BI SERIES UNIT MUST BE EXTENDED TO THE FLOOR TO COMPLETE THE INSTALLATION.
PAGE 2
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) A. Heater Installation Instructions NOTE: Heater assembly MUST be attached to right side of left hand unit. 1. Clear foil from mounting holes of Heater Assembly. 2. Place heater against right side of unit with wires up and foil side in, positioning the heater 2” (51mm) from top edge of cabinet and 1” (25mm) from back edge of cabinet (See Figure 1). 3.
PAGE 3
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) B. Center Trim Installation Instructions NOTE: Assemble center trim piece and trim brackets first, then attach trim to right side of left hand unit. 1. Attach the three L-Shaped Dual Trim Bracket Assemblies to the Dual Install Center Trim Piece, using nuts provided. DO NOT tighten nuts at this time (See Figures 2). 2.
PAGE 4
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) D. Main Frame Shim Installation Instructions Shim Top View of Main Frame and Shim NOTE: Shim Assembly MUST be attached to back of the left side main frame of the right hand unit. 1. Remove the left side mainframe from the right hand unit (See Figure 6). 2. Remove the backing paper from the double-stick tape that is attached to the main frame shim. 3.
PAGE 5
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) F. Join Units Together at Bottom 1. All-Refrigerator and All-Freezer Models i. Using a 1/2'' wrench, loosen the four bolts (2 each unit) at bottom adjoining corners of the appliances, leaving a 1/8'' (3mm) to 1/4” (6mm) gap between bolt heads and unit shell bottom (See Figure 7). ii.
PAGE 6
7004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) H. Join Units Together at Top 1. Working the Dual Installation Top Bracket in from the side, line the holes of the top bracket up with the threaded inserts at the top adjoining corners of the appliances (See Figure 10). 2. Insert four 5-/16-18 X 3/4” Tensilock Bolts down through the bracket into the threaded inserts and tighten the bolts (See Figure 10). I.
PAGE 7
004808, 7004809, 7004810, 7004811, 7004812, 7004813, 7012623, 7012624 (Instructions for Dual Grille Kits Listed Above) 3. Lift dual grille assembly up, align slide bracket with slot of dual grille support bracket and push grille assembly toward units so that the slide bracket slides into the slot of the support bracket (See Figure 13).