User Guide

41
Dimensions in parentheses are in
millimeters unless otherwise specified.
WOLF WARMING DRAWERS
PLANNING INFORMATION
The Wolf 30" (762) warming drawer is shipped
without any decorative drawer front. You must
order one of three stainless steel drawer fronts
(tubular handle included) in classic, platinum or
carbon finish, or the integrated front (no handle)
for a custom wood application.
Specifications on the following pages provide
overall dimensions, rough openings and installa-
tion options for Model WWD30 with stainless
steel and integrated drawer fronts. Note that
there are significant differences to the installa-
tion requirements for the integrated drawer front.
An anti-tip block must be installed to prevent
the unit from tipping forward when the drawer
is opened.
The base platform must be able to support 200
lbs (91 kg). This platform must be a minimum of
1" (25) above the toe kick to allow for the
5
/8"
(16) overlap of the warming drawer trim.
Model WWD30 may be installed below a Wolf
built-in oven or an electric or gas cooktop,
provided the warming drawer is fully enclosed,
top and bottom. It may also be installed next to
or above another Model WWD30. Dimensions
will vary according to the specific installation.
STAINLESS STEEL DRAWER FRONT
Wolf recommends using a 33" (838) wide
cabinet for the warming drawer with stainless
steel drawer front. A minimum 30" (762) wide
by 24" (610) deep cabinet is required.
INTEGRATED DRAWER FRONT
IMPORTANT NOTE: A minimum 33" (838) wide
by 26" (660) deep cabinet is required for the
warming drawer with integrated drawer front.
Model WWD30 with integrated drawer front can
accommodate installations with a 30" (762) or
36" (914) cooktop. It may also be installed in
combination with a 30" (762) single or double
oven or a 36" (914) single oven. Dimensions will
vary according to the specific installation.
Keep in mind that the width of the custom panel
for the warming drawer with integrated drawer
front will vary according to the specific installa-
tion. The opening width will remain 29
1
/2" (749)
whether installed in combination with a 30"
(762) or 36" (914) cooktop or oven.
The decorative wood drawer front panel must
be a minimum of
5
/8" (16) thick.
ELECTRICAL REQUIREMENTS
Model WWD30 requires a separate, grounded
120 V AC, 60 Hz power supply. The service
should have its own 15 or 20 amp circuit
breaker, and a grounded 3-prong receptacle
should be located within reach of the power
cord and flush with the back wall. Locate
electrical within the shaded area shown in the
installation illustrations on the following pages.
IMPORTANT NOTE: When installed outdoors, a
ground fault circuit interrupter (GFCI) is required
to reduce the risk of electrical shock.
FRONT PANEL OPTIONS
Model WWD30
Classic Stainless WWDFRONT/S
Platinum Stainless WWDFRONT/P
Carbon Stainless WWDFRONT/B
Integrated WWDFRONT/I
(accepts wood panel)
Optional drawer front panels are
ordered and shipped as sales
accessories. Stainless steel drawer
front panels include matching tubular
handle.
23
1
/2" (597)
BEHIND FRAME
29
7
/8" (759)
OVERALL WIDTH
9"
(229)
27
1
/8" (689)
OVERALL DEPTH
10
1
/4"
(260)
OVERALL DIMENSIONS
Model WWD30 with Stainless Steel Drawer Front
ACCESSORIES
Optional accessories
are available
through your Wolf
dealer. To obtain
local dealer
information, visit
the Locator section
of our website,
wolfappliance.com.
29
3
/8" (746)
OVERALL WIDTH
23
1
/2" (597)
BEHIND FRAME
9"
(229)
10
1
/8"
(257)
Model WWD30 with Integrated Drawer Front