Maintenance and care 4-1. Maintenance and care Cleaning and protecting the vehicle exterior......... 276 Cleaning and protecting the vehicle interior.......... 280 Cleaning and protecting the Alcantara® area ....... 284 4 4-2. Maintenance Maintenance requirements .................. 286 General maintenance....... 289 Emission inspection and maintenance (I/M) programs........................ 292 4-3. Do-it-yourself maintenance Do-it-yourself service precautions .................... Engine hood..............
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. ● Wash the vehicle body using a sponge or soft cloth, such as a chamois. ● For hard-to-remove marks, use car wash soap and rinse thoroughly with water. ● Wipe away any water.
4-1. Maintenance and care ■ Automatic car washes ● Fold the mirrors before washing the vehicle. Start washing from the front of the vehicle. Make sure to and extend the mirrors before driving. ● When having your vehicle washed in an automatic car wash, make sure beforehand that the car wash is of suitable type to avoid scratches to the vehicle surface and harm to your vehicle’s paint. ● Vehicles with a rear spoiler: In certain automatic car washes, the rear spoiler may interfere with machine operation.
-1. Maintenance and care WARNING ■ When washing the vehicle ● Do not wash the engine compartment and area adjacent to it. If water enters the engine air intake or electrical parts it will cause engine trouble or a malfunction of the power steering. ● When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes.
4-1. Maintenance and care CAUTION ■ Cleaning the exterior lights ● Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surfaces of the lights. ● Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. ■ To prevent damage to the windshield wiper arms When lifting the wiper arms away from the windshield, pull the driver side wiper arm upward first, and repeat for the passenger side.
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior ● Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water. ● When the interior is extremely dirty, wipe away the dirt using a soft cloth slightly dampened with diluted neutral detergent.
4-1. Maintenance and care ■ Caring for leather areas SUBARU recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. Excellent results are obtained by keeping the carpet as dry as possible. ■ Seatbelts Clean with mild soap and lukewarm water using a cloth or sponge.
4-1. Maintenance and care CAUTION ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ● Do not use polish wax or polish cleaner. The instrument panel's or other interior part’s painted surface may be damaged.
4-1. Maintenance and care CAUTION ■ Cleaning the inside of the rear window ● Be careful not to scratch or damage the heater wires. ● Do not use glass cleaner to clean the rear window, as this may cause damage to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.
4-1. Maintenance and care Cleaning and protecting the Alcantara® area∗ The following procedures will protect and keep your vehicle’s Alcantara® upholstery in top condition: ■ Day-to-day cleaning Perform the following procedures regularly (approximately once a month). STEP 1 Wipe the entire Alcantara® area with a soft cloth that has been dampened with lukewarm water (approximately 104°F [40°C]) and squeezed out. Do not wipe too hard. Doing so may make the Alcantara® upholstery surface become uneven.
4-1. Maintenance and care STEP 2 If the Alcantara® upholstery surface becomes uneven, lightly brush it with a soft brush. STEP 3 Allow the surface to dry completely. ■ Oil stains You will need the following items: ● A cloth that has been dampened with benzene ● A dry cloth STEP 1 Using a dry cloth or tissue paper, wipe away as much of the oil as possible to prevent the stained area from expanding.
4-2. Maintenance Maintenance requirements To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. SUBARU recommends the following maintenance. ■ General maintenance Should be performed on a daily basis. This can be done by yourself or by a SUBARU dealer. ■ Scheduled maintenance Should be performed at specified intervals according to the maintenance schedule.
4-2. Maintenance ■ Allow inspection and repairs to be performed by a SUBARU dealer ● SUBARU technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle. ● Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your SUBARU dealer will promptly take care of it.
4-2. Maintenance WARNING ■ If your vehicle is not properly maintained It could result in serious damage to the vehicle and possible serious injury or death. ■ Warning in handling of battery ● Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and lighters. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive.
4-2. Maintenance General maintenance Listed below are the general maintenance items that should be performed at the intervals specified in the “Warranty and Maintenance Booklet”. It is recommended that any problem you notice should be brought to the attention of your SUBARU dealer or qualified service shop for advice. Engine compartment Items Check points Check the connections. (→P. 306) Brake fluid At the correct level? (→P. 304) Engine coolant At the correct level? (→P.
4-2.
4-2. Maintenance Vehicle exterior Items Check points • Operate smoothly? Engine hood • The lock system works properly? Fluid leaks • Is there any leakage after parking? Tire • Inflation pressure is correct? • Tire surfaces not worn or damaged? • Tires rotated according to the maintenance schedule? • Wheel nuts are not loose? Windshield wipers • The wiper blades should not show any signs of cracking, splitting, wear, contamination or deformation.
4-2. Maintenance Emission inspection and maintenance (I/M) programs Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. ■ If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your SUBARU dealer to service the vehicle.
4-3. Do-it-yourself maintenance Do-it-yourself service precautions If you perform maintenance yourself, be sure to follow the correct procedure as given in these sections. Items Parts and tools (→P. 304) • FMVSS No.116 fresh DOT 3 or DOT 4 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) (→P. 302) • SUBARU Super Coolant or similar high-quality ethylene glycolbased non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
4-3. Do-it-yourself maintenance Items Light bulbs Parts and tools (→P. 343) Radiator and condenser (→P. 304) 294 BRZ_U • Bulb with same number and wattage rating as original • Phillips-head screwdriver • Flathead screwdriver Tire inflation pressure (→P. 320) • Tire pressure gauge • Compressed air source Washer fluid • Water washer fluid containing antifreeze (for winter use) • Funnel (→P.
4-3. Do-it-yourself maintenance WARNING The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions. ■ When working in the engine compartment ● Keep hands, clothing, and tools away from the moving fan and engine drive belt. ● Be careful not to touch the engine, radiator, exhaust manifold, etc. right after driving as they may be hot. Oil and other fluids may also be hot.
4-3. Do-it-yourself maintenance Engine hood Release the lock from the inside of the vehicle to open the engine hood. STEP 1 Pull the engine hood release lever. The engine hood will pop up slightly. STEP 2 Push the auxiliary catch lever to the left and lift the engine hood. STEP 3 Hold the engine hood open by inserting the supporting rod into the slot.
4-3. Do-it-yourself maintenance WARNING ■ Pre-driving check Check that the engine hood is fully closed and locked. If the engine hood is not locked properly it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. CAUTION ■ When opening the engine hood ● Do not lift up or operate the wipers. Doing so may cause the engine hood and wipers to contact, scratching the engine hood.
4-3. Do-it-yourself maintenance Engine compartment Battery (→P. 306) Engine oil level dipstick (→P. 299) Washer fluid tank (→P. 310) Electric cooling fans Brake fluid reservoir (→P. 304) Condenser (→P. 304) Radiator (→P. 304) Engine oil filler cap (→P. 300) Engine coolant reservoir (→P. 302) Fuse box 298 BRZ_U (→P.
4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP 1 Park the vehicle on level ground. After warming up the engine and turning it off, wait more than five minutes for the oil to drain back into the bottom of the engine. STEP 2 Hold a rag under the end and pull the dipstick out. 4 Wipe the dipstick clean. STEP 4 Reinsert the dipstick fully.
4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil. Engine oil selection Oil quantity (Low → Full) Items →P. 420 1.1 qt. (1.0 L, 0.9 Imp. qt.) Clean funnel STEP 1 Remove the oil filler cap by turning it counterclockwise. STEP 2 Add engine oil slowly, checking the dipstick.
4-3.
4-3. Do-it-yourself maintenance CAUTION ■ To prevent serious engine damage Check the oil level on a regular basis. ■ When replacing the engine oil ● Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, or the engine could be damaged. ● Check the oil level on the dipstick every time you fill the oil. ● Be sure the engine oil filler cap is properly tightened.
4-3. Do-it-yourself maintenance ■ Coolant selection Only use SUBARU Super Coolant or similar high-quality ethylene glycolbased non-silicate, non-amine, non-nitrite, and non-borate coolant with longlife hybrid organic acid technology. SUBARU Super Coolant is a mixture of 50% coolant and 50% deionized water. (Enabled: -31°F [-35°C]) For more details about engine coolant, contact your SUBARU dealer. WARNING ■ When the engine is hot Do not remove the radiator cap.
4-3. Do-it-yourself maintenance Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your SUBARU dealer. WARNING ■ When the engine is hot Do not touch the radiator or condenser as they may be hot and cause serious injuries, such as burns. Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank.
4-3. Do-it-yourself maintenance ■ Adding fluid Make sure to check the fluid type and prepare the necessary items. Fluid type Items FMVSS No.116 fresh DOT 3 or DOT 4 brake fluid Clean funnel ■ Brake fluid can absorb moisture from the air Excess moisture in the fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid. WARNING ■ When filling the reservoir Take care because brake fluid can harm your hands or eyes and damage painted surfaces.
4-3. Do-it-yourself maintenance Battery Check the battery as follows. ■ Battery exterior Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Hold-down clamp Terminals ■ Checking battery fluid Check that the level is between “UPPER LEVEL” and “LOWER LEVEL”. “UPPER LEVEL” “LOWER LEVEL” If the fluid level is at or below “LOWER LEVEL”, add distilled water.
4-3. Do-it-yourself maintenance ■ Adding distilled water Low O.K. STEP 1 Remove the vent plug. STEP 2 Add distilled water. If the “UPPER LEVEL” line cannot be seen, check the fluid level by looking directly at the cell. STEP 3 Put the vent plug back on and close securely.
4-3. Do-it-yourself maintenance ■ Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: ● If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable. ● Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
4-3. Do-it-yourself maintenance WARNING ■ Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: ● Do not cause sparks by touching the battery terminals with tools. ● Do not smoke or light a match near the battery. ● Avoid contact with eyes, skin and clothes. ● Never inhale or swallow electrolyte.
4-3. Do-it-yourself maintenance CAUTION ■ When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. ■ When adding distilled water Avoid overfilling. Water spilled during battery recharging may cause corrosion. Washer fluid If the washer fluid level is at “LOW”, add washer fluid.
4-3. Do-it-yourself maintenance WARNING ■ When adding washer fluid Do not add washer fluid when the engine is hot or running, as washer fluid contains alcohol and may catch fire if spilled on the engine etc. CAUTION ■ Washer fluid Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces. ■ Diluting washer fluid Dilute washer fluid with water as necessary.
4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance schedules and treadwear. ■ Checking tires New tread Treadwear indicator Worn tread The location of treadwear indicators is shown by the “TWI” or “ ” marks, etc., molded on the sidewall of each tire. Check spare tire condition and pressure if not rotated. ■ Tire rotation Rotate the tires in the order shown.
4-3. Do-it-yourself maintenance Installing tire pressure warning valves and transmitters (vehicles with a tire pressure monitoring system) When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and tire pressure monitoring system must be initialized.
4-3. Do-it-yourself maintenance Registering ID codes (vehicles with a tire pressure monitoring system) The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your SUBARU dealer.
4-3. Do-it-yourself maintenance ■ Maximum load of tire Check that the maximum load of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire. (→P.
4-3. Do-it-yourself maintenance ■ Initializing the tire pressure monitoring system (if equipped) Initialize the system with the tire inflation pressure adjusted to the specified level. ■ Routine tire inflation pressure checks (vehicles with a tire pressure monitoring system) The tire pressure monitoring system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.
4-3. Do-it-yourself maintenance WARNING ■ Tire pressure monitoring system operation (if equipped) The tire pressure monitoring system may not provide warning immediately if a tire bursts or if sudden air leakage occurs. ■ When inspecting or replacing tires Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury.
4-3. Do-it-yourself maintenance CAUTION ■ Repairing or replacing tires, wheels, tire pressure warning valves, transmitters and tire valve caps (vehicles with a tire pressure monitoring system) ● When removing or fitting the wheels, tires or the tire pressure warning valves and transmitters, contact your SUBARU dealer as the tire pressure warning valves and transmitters may be damaged if not handled correctly. ● When replacing tire valve caps, do not use tire valve caps other than those specified.
4-3. Do-it-yourself maintenance CAUTION ■ Low profile tires and wheels (vehicles with 17-inch tires) Low profile tires may cause greater damage than usual to the wheel when receiving impact from the road surface. Therefore pay attention to the following: ● Be sure to use proper tire inflation pressure. If tires are under-inflated, they may be damaged more severely. ● Avoid pot holes, uneven pavement, curbs and other road hazards. Failure to do so may lead to severe tire and wheel damage.
4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is displayed on the tire and loading information label. (→P.
4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge STEP 1 Remove the tire valve cap. STEP 2 Press the tip of the tire pressure gauge onto the tire valve. STEP 3 Read the pressure using the graduations of the gauge. STEP 4 If the tire inflation pressure is not within the recommended levels, adjust the pressure. If you add too much air, press the center of the valve to lower.
4-3. Do-it-yourself maintenance ■ Effects of incorrect tire inflation pressure Driving with incorrect tire inflation pressure may result in the following: ● Reduced fuel efficiency ● Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your SUBARU dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ● Check only when the tires are cold.
4-3. Do-it-yourself maintenance WARNING ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury.
4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at your SUBARU dealer. *: Conventionally referred to as “offset”.
4-3. Do-it-yourself maintenance ■ When replacing wheels (vehicles with a tire pressure monitoring system) The wheels of your SUBARU are equipped with tire pressure warning valves and transmitters that allow the tire pressure monitoring system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P.
4-3. Do-it-yourself maintenance CAUTION ■ Replacing tire inflation pressure warning valves and transmitters (vehicles with a tire pressure monitoring system) ● Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your SUBARU dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your SUBARU dealer.
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method STEP 1 Vehicles without a keyless access with push button start system Turn the engine switch off. Vehicles with a keyless access with push button start system Turn the push-button ignition switch off. STEP 2 Open the glove box. Slide off the damper.
4-3. Do-it-yourself maintenance STEP 4 Lower the glove box slowly until surface is horizontal with the floor, then pull it out. (Simply pulling with gentle force will disengage the lower claws.) Lower claw Lower point claw engagement Do not forcibly pull the glove box. Otherwise, the lower claws or the lower claw engagement points may be deformed, making it difficult to reinstall or close the glove box. STEP 5 Remove the filter cover.
4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Warranty and Maintenance Booklet”.) ■ If air flow from the vents decreases dramatically The filter may be clogged. Check the filter and replace if necessary.
4-3. Do-it-yourself maintenance Transmitter/access key battery Replace the battery with a new one if it is depleted. ■ You will need the following items: ● Flathead screwdriver ● Lithium battery CR2016 (vehicles without a keyless access with push button start system), or CR2032 (vehicles with a keyless access with push button start system) ■ Replacing the battery (vehicles without a keyless access with push button start system) STEP 1 Remove the cover.
4-3. Do-it-yourself maintenance Open the case cover using a coin protected with tape and remove the depleted battery. STEP 3 Insert a new battery with the “+” terminal facing up. ■ Replacing the battery (vehicles with a keyless access with push button start system) Take out the mechanical key. STEP 1 4 Groove Insert the tip of a flathead screwdriver into the groove and remove the cover. To prevent damage to the key, wrap the tip of the screwdriver with protective tape.
4-3. Do-it-yourself maintenance STEP 3 Remove the depleted battery. To prevent damage to the key, wrap the tip of the screwdriver with protective tape. STEP 4 Install a new battery with the “+” terminal facing up, as shown in the illustration. STEP 5 Align the protruding part with the slot and install the cover.
4-3. Do-it-yourself maintenance ■ Use a CR2016 (vehicles without a keyless access with push button start system) or CR2032 (vehicles with a keyless access with push button start system) lithium battery ● Batteries can be purchased at your SUBARU dealer, local electrical appliance shops or camera stores. ● Replace only with the same or equivalent type recommended by the manufacturer. ● Dispose of used batteries according to local laws.
4-3. Do-it-yourself maintenance CAUTION ■ For normal operation after replacing the battery Observe the following precautions to prevent accidents: ● Always work with dry hands. Moisture may cause the battery to rust. ● Do not touch or move any other component inside the remote control. ● Do not bend either of the battery terminals.
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP 1 Vehicles without a keyless access with push button start system Turn the engine switch off. Vehicles with a keyless access with push button start system Turn the push-button ignition switch off. STEP 2 Open the fuse box cover. Engine compartment Push the tabs in and lift the lid off.
4-3. Do-it-yourself maintenance STEP 3 After a system failure, see “Fuse layout and amperage ratings” (→P. 338) for details about which fuse to check. STEP 4 Remove the fuse with the pullout tool. STEP 5 Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact your SUBARU dealer. Type D Normal fuse Blown fuse Contact your SUBARU dealer.
4-3. Do-it-yourself maintenance Fuse layout and amperage ratings ■ Engine compartment Fuse Circuit 1 MIR HTR 7.5 A Outside rear view mirror defoggers 2 RDI 25 A Electric cooling fan 3 (PUSH-AT) 7.5 A Engine control unit 4 ABS NO.
4-3. Do-it-yourself maintenance Fuse Ampere Circuit SPARE See note. Spare fuse 17 SPARE See note. Spare fuse 18 SPARE See note. Spare fuse 19 SPARE See note. Spare fuse 20 SPARE See note. Spare fuse 21 ST 7.5 A Starting system 22 ALT-S 7.5 A Charging system 23 (STR LOCK) 7.5 A Steering lock system 24 D/L 20 A Power door lock 25 ETCS 15 A Engine control unit 26 (AT+B) 7.5 A Transmission 27 (AM2 NO. 2) 7.
4-3. Do-it-yourself maintenance Fuse Ampere Circuit 37 HORN NO. 2 7.5 A Horn 38 HORN NO. 1 7.5 A Horn 39 H-LP LH LO 15 A Left-hand headlight (low beam) 40 H-LP RH LO 15 A Right-hand headlight (low beam) 41 H-LP LH HI 10 A Left-hand headlight (high beam) 42 H-LP RH HI 10 A Right-hand headlight (high beam) 43 INJ 30 A Multiport fuel injection system/ sequential multiport fuel injection system 44 H-LP WASHER 30 A 45 AM2 NO.
4-3. Do-it-yourself maintenance ■ Instrument panel Fuse Ampere ECU ACC 10 A 2 16 P/POINT No.2 PANEL TAIL DRL STOP OBD HEATER-S HEATER FR FOG LH FR FOG RH BK/UP LP ECU IG1 AM1 AMP AT UNIT 15 A 10 A 10 A 10 A 7.5 A 7.5 A 7.5 A 10 A 10 A 10 A 7.5 A 10 A 7.5 A 15 A 15 A 17 GAUGE 7.5 A 3 4 5 6 7 8 9 10 11 12 13 14 15 ECU IG2 SEAT HTR LH 20 SEAT HTR RH 21 RADIO 22 P/POINT No.1 18 19 10 A 10 A 10 A 7.
4-3. Do-it-yourself maintenance ■ After a fuse is replaced ● If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (→P. 343) ● If the replaced fuse blows again, have the vehicle inspected by your SUBARU dealer. ■ If there is an overload in the circuits The fuses are designed to blow, protecting the wiring harness from damage. WARNING ■ To prevent system breakdowns and vehicle fire Observe the following precautions.
4-3. Do-it-yourself maintenance Light bulbs You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your SUBARU dealer. ■ Preparing a replacement light bulb Check the wattage of the light bulb being replaced. (→P.
4-3.
4-3. Do-it-yourself maintenance Replacing light bulbs ■ Front turn signal lights STEP 1 Turn the bulb base counterclockwise. STEP 2 3 Remove the light bulb. 4 Maintenance and care STEP 3 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Front side marker lights STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. STEP 2 Remove the clips and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 3 Release the light's claw. Insert the screwdriver into the hole.
4-3. Do-it-yourself maintenance Remove the light bulb. STEP 5 STEP 6 When installing, reverse the steps listed. ■ Front fog lights (if equipped) STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. Remove the clips and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag.
4-3. Do-it-yourself maintenance STEP 3 Unplug the connector while depressing the lock release. STEP 4 Remove the light bulb. STEP 5 348 BRZ_U When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Rear side marker lights STEP 1 Remove a clip and partly remove the cover. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 2 Turn the bulb base counterclockwise. 4 STEP 4 Remove the light bulb. Maintenance and care STEP 3 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Rear turn signal lights STEP 1 Remove a clip and partly remove the cover. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 2 Turn the bulb base counterclockwise. STEP 3 Remove the light bulb. STEP 4 350 BRZ_U When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Back-up lights STEP 1 Turn the bulb base counterclockwise. STEP 2 3 Remove the light bulb. 4 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ License plate lights STEP 1 Remove the trunk lid panel cover clips and partly remove the trunk lid panel cover. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 2 Turn the bulb base counterclockwise. STEP 3 Remove the light bulb. STEP 4 352 BRZ_U When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Interior light STEP 1 Remove the lens. To prevent damage to the interior light, cover the tip of the screwdriver with a rag. STEP 2 Remove the light bulb. 4 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Vanity lights (if equipped) STEP 1 Open the cover and remove the lens. To prevent damage to the vanity light, cover the tip of the screwdriver with a rag. STEP 2 STEP 3 354 BRZ_U Remove the light bulb. When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance ■ Replacing the following bulbs If any of the lights listed below has burnt out, have it replaced by your SUBARU dealer. ● Headlight high and low beams ● Parking lights ● Daytime running lights ● Stop/tail lights ● High mounted stoplight ● Door courtesy lights (if equipped) ■ Condensation build-up on the inside of the lens Contact your SUBARU dealer for more information in the following situations.
4-3. Do-it-yourself maintenance ■ When replacing light bulbs SUBARU recommends that you use genuine SUBARU products designed for this vehicle. Because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable. ■ Removing and installing the luggage trim cover and trunk lid panel cover clip Removing Installing WARNING ■ Replacing light bulbs ● Turn off the lights.
4-3. Do-it-yourself maintenance WARNING ■ Discharge headlights ● Contact your SUBARU dealer before replacing the discharge headlights (including light bulbs). ● Do not touch the discharge headlight’s high voltage socket when the headlights are turned on. An extremely high voltage of 25000 V will be discharged and could result in serious injury or death by electric shock.
4-3.
