Instructions / Assembly

NOTE: AFTER ABOUT 1- INCH OF WATER IS ON THE BOTTOM, STOP FILLING AND SMOOTH
WRINKLES OUT OF THE BOTTOM OF THE POOL WORKING THEM FROM THE CENTER OUTWARD.
BE SURE FLOOR OF POOL IS ROUND AND FLAT. Next pull the outer wall out from under the top ring,
all around the bottom of the pool, so that it fills evenly.
NOTE: IF MORE THAN 1-2 INCHES OF WATER COLLECTS ON ANY ONE SIDE BEFORE THE POOL
STARTS FILLING IN THE CENTER, THE POOL IS NOT LEVEL ENOUGH, AND MUST BE CORRECTED,
SEE “SITE PREPARATION”, ABOVE.
D. NOTE: THE WEIGHT OF THE WATER WILL PREVENT ADJUSTMENT AFTER THIS POINT.
E. Now, as you continue filling, the inflated ring will rise as the water deepens. Max. Water Level is the
bottom seam of the inflatable ring; this information is printed on the ring. Once this is done, refer back
to the “Swimming Pool Filter System” owner’s manual, and continue from Step “D” on through the rest
of the installation if you have a filter/pump system.
Should you encounter any problems, contact the Customer Service at [phone].
Extended operating days and hours during peak season requirements.
Should you encounter any problems, contact the Customer Service at [phone].
Extended operating days and hours during peak season requirements.
5 6
POOL COVER SAFETY
IF YOU ARE GOING TO USE A POOL COVER, SOLAR COVER OR SOLAR
BLANKET, PLEASE READ THIS INFORMATION.
VERY IMPORTANT
DO NOT USE A POOL COVER, SOLAR COVER OR SOLAR
BLANKET ON THIS POOL IF IT DOES NOT HAVE THIS TYPE OF
WARNING LABEL ON THE COVER.
DANGER
Competent supervision and knowledge of the safety requirements
is the only way to prevent drowning or permanent injury
in the use of this product!
Never leave young children unattended.
3 DISASSEMBLY AND STORAGE
GENERAL INFORMATION: Pool must be stored if temperatures are expected to fall below 32°F.
A. All parts should be cleaned with a mild soap and lukewarm water only - DO NOT use detergent or
hot water.
B. Make sure all parts are dry before storing to help prevent mildew from forming.
C. Store all parts in a dry heated area where temperatures do not go below 32° F or above 125° F.
D. Failure to follow the proper storage instructions could cause damage to pool parts and void warranty.
E. YOU MUST FOLLOW THE ASSEMBLY INSTRUCTIONS TO REASSEMBLE YOUR POOL NEXT SEASON. Pool
site must be cleared and leveled again before setting up your pool.
QUICK-SET® POOL:
A. To drain the pool, locate the drain plug on the outside of the pool wall and remove the drain cap. A
standard garden hose will thread onto the drain fitting. Extend the hose to the area where the water is
to be drained. When you have placed the garden hose where desired, the drain plug on the inside of
the pool can be opened.
B. Once you have drained as much water as possible out of the pool, using the hose connected to the
drain fitting, open the air valve and deflate the top ring. Then, carefully push the sides of the pool wall
down to allow remaining water to run out.
C. Remove any remaining water as you wash and completely dry pool using a soft cotton cloth. Push the
drain plug into the fitting and replace the cap.
D. Frame Pools: If your pool has metal frame work, disassemble those pieces by depressing the plastic
buttons sliding those pieces apart or by removing the plastic pins holding them together again sliding
those pieces apart, clean them and wipe them dry. If in doubt of proper disassembly refer to the pools
set-up sheet and reverse those steps. Place them all together in a safe storage place for reassembly next
season. Order replacement parts for any damaged, broken, or worn parts.
E. Solar blankets, leaf covers, ladders, etc., should be cleaned and dried before storing.
POOL COVER WARNING
SOLAR COVER WARNING
SOLAR BLANKET WARNING
!
WARNING
AVOID DROWNING RISK
STAY OFF COVER - WILL NOT SUPPORT WEIGHT.
KEEP CHILDREN AWAY. CHILDREN OR OBJECTS CAN
NOT BE SEEN UNDER COVER.
REMOVE STANDING WATER - CHILD CAN DROWN ON
TOP OF COVER.
REMOVE COVER COMPLETELY BEFORE ENTRY OF
BATHERS - ENTRAPMENT POSSIBLE.
NON-SECURED OR IMPROPERLY SECURED COVERS
ARE A HAZARD.
FAILURE TO FOLLOW ALL INSTRUCTIONS MAY
RESULT IN INJURY OR DROWNING.
THIS IS NOT A SAFETY COVER.
TYPE OC COVER CLASSIFICATION.
INSTALL COVER WITH LABELS FACING UP.
USE DRAWSTRING TO SECURE COVER TO POOL.
THIS COVER MEETS REQUIREMENTS DESCRIBED
IN SPECIFICATION F-1346 (ASTM).
!
WARNING
AVOID DROWNING RISK
STAY OFF COVER - WILL NOT SUPPORT WEIGHT.
KEEP CHILDREN AWAY. CHILDREN OR OBJECTS CAN
NOT BE SEEN UNDER COVER.
REMOVE STANDING WATER - CHILD CAN DROWN ON
TOP OF COVER.
REMOVE COVER COMPLETELY BEFORE ENTRY OF
BATHERS - ENTRAPMENT POSSIBLE.
NON-SECURED OR IMPROPERLY SECURED COVERS
ARE A HAZARD.
FAILURE TO FOLLOW ALL INSTRUCTIONS MAY
RESULT IN INJURY OR DROWNING.
THIS IS NOT A SAFETY COVER.
TYPE OC COVER CLASSIFICATION.
INSTALL COVER WITH LABELS FACING UP.
LAY COVER ON TOP SURFACE OF WATER.
THIS COVER MEETS REQUIREMENTS DESCRIBED
IN SPECIFICATION F-1346 (ASTM).