SUMMERS ® Operator’s Manual CULTI-HARROW SUPERHARROW 3-RANK SUPERWEEDER HDC IMPORTANT THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE SINCE MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.com MADDOCK, NORTH DAKOTA 58348 .................................. (701) 438-2855 DEVILS LAKE, NORTH DAKOTA 58301 ............................. (701) 662-5391 8Z1100 © Summers Mfg.
Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 12 months from the date of purchase by the end user from Summers’ dealer.
INTRODUCTION This manual provides information about Safety, Assembly, Operation and Parts for the Summers Culti-Harrow, Superharrow and 3-Rank Superweeder featuring the Summers 16 and 20 Ft. Hitch. Please refer to these sections before assembling or operating your machine. Reference to “right” and “left” in this book is determined when the machine is viewed from the rear. It is the policy of the company to improve its products whenever possible and practical to do so.
TABLE OF CONTENTS SECTION 1: SAFETY: ALL MACHINES Safety-Alert Symbol & General Safety Practices ..................................................................................... 1-1, 1-2 Safety Decals & Reflectors ........................................................................................................................ 1-3 - 1-7 General Assembly Safety Practices ....................................................................................................................
SECTION 1 - SAFETY SAFETY-ALERT SYMBOL This symbol is used to denote possible danger And care should be taken to prevent bodily Injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. DANGER WARNING CAUTION indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.
SECTION 1 - SAFETY SAFETY DURING TRANSPORT 1. ONLY TOW at a safe speed. Use caution when making corners or meeting traffic. 2. USE a safety chain between tractor drawbar and implement hitch when transporting on public roads. 3. ALWAYS use transport locks when transporting on public roads. 4. COMPLY with local lighting, marking and maximum width regulations when transporting on highways. WARNING IMPORTANT INFORMATION ON 16 & 20 FT. HITCH MACHINES WITH NEGATIVE HITCH WEIGHT 4.
SECTION 1 - SAFETY SAFETY DECALS 1. KEEP SAFETY DECALS AND REFLECTORS CLEAN. 2. REPLACE missing or unreadable decals. New decals are available from your Summers dealer by stating correct part number (PN) located in lower right hand corner. 1. TRANSPORT LOCK DECAL (PN 8Z0075) – Used on all machines. 2. HITCH WARNING DECAL (PN 8Z0092) 3.
SECTION 1 - SAFETY 4. AUTO-FOLD ARM WARNING DECAL (PN 8Z0232) 5. GENERAL CAUTION DECAL (PN 8Z0276) 6.
SECTION 1 - SAFETY 7. ELECTROCUTION DANGER DECAL (PN 8Z0346) 8. AMBER REFLECTOR (PN 8Z0800) 9. RED-ORANGE REFLECTOR (PN 8Z0805) 10.
SECTION 1 - SAFETY 11.
SECTION 1 - SAFETY 1-7
SECTION 1 - SAFETY GENERAL ASSEMBLY SAFETY PRACTICES BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking. YOU ARE RESPONSIBLE for the safe assembly of the machine. DO NOT ALLOW CHILDREN or other unauthorized persons within the assembly area. ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear. BE SURE LIFTING DEVICE IS RATED TO HANDLE THE WEIGHT.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW Fig. 1 The machine should be placed in an area that allows ample room for assembly in field position (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. Refer to illustrations and parts listing on pages 8-2 through 8-20 and follow these steps when assembling. 16’ HITCH ASSEMBLY HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW Fig. 2 20’ HITCH ASSEMBLY Bolt the two A-frame sections of the hitch together, using eight 7/8” bolts and locknuts. NOTE: Since these larger pieces have a tendency to warp when welded, it may be necessary to pull the legs of the hitch together to match the center tube brackets. HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires. Mount hitch wheels and tires and install hitch jack.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW LIFT ARMS Attach the lift arms to the wing tubes using 7/16” x 7-1/4” bolts. Start at machine center and measure outward using the following guide. All measurements are to the center of the lift arms. The end lift arm on each wing should be close to the end wheel so the section harrows out the wheel track. In cases where both 5-1/2’ and 7’ sections are used on the wings, the 7’ sections are used on the ends.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW more information. WING TUBE JACK BRACKET Harrows without sprayers on hitch may require the transport wheel assemblies to be positioned further ahead to provide a better balance on the hitch. A wing tube jack bracket is provided with all machines and allows for mounting the hitch jack on the wing tube for added stability. (See Fig. 6). CABLES Install cable brackets and cable assemblies as shown in figures 1, 2 and 7.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW HYDRAULIC SYSTEMS FOR MACHINES WITH 16 OR 20 FT. HITCHES Mount lift cylinders and assemble hose lines as shown in figures 19 and 20. the lift cylinders requires a restrictor valve on the tractor end. Thread this valve on with the arrow pointing back towards the cylinders as illustrated. NOTE: The hydraulic line leading from the rod-end of Fig. 19 Hydraulic Lift System - 16 ft.
SECTION 2 – SET-UP INSTRUCTIONS — CULTI-HARROW Fig. 20 Hydraulic Lift System - 20 ft.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Fig. 1 The machine should be placed in an area that allows ample room for assembly in field position (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. Refer to illustrations and parts listing on pages 8-2 to 8-20 and follow these steps when assembling. 16’ HITCH ASSEMBLY HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Fig. 2 20’ HITCH ASSEMBLY Bolt the two A-frame sections of the hitch together, using eight 7/8” cap screws and locknuts. NOTE: Since these larger pieces have a tendency to warp when welded, it may be necessary to pull the legs of the hitch together to match the center tube brackets. HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires. Mount hitch wheels and tires and install hitch jack.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Use CAUTION when making manual height adjustments. For Safety purposes, block equipment while working on it. On the center two sections only, move the lower stop bolt and bushing to the front hole (Fig. 12). This will allow the sections to raise more evenly. To compensate for various soil conditions and tooth wear, the sections can be mounted in four different positions as shown below. Suggested Initial Setting Fig.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW WING TUBE JACK BRACKET A wing tube jack bracket is provided with all machines and allows for mounting the hitch jack on the wing tube for more stability (See Fig. 6). CABLES Install cable brackets and cable assemblies as shown in figures 1, 2 and 7. Secure brackets using 3/4” U-bolts, lock washers and nuts. Two cables are required for each wing on the split wing models. NOTE: Adjust cables so wings slightly lead center when standing in field position.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Fig.
3-6 SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Fig.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW HYDRAULIC SYSTEMS FOR MACHINES WITH 16 OR 20 FT. HITCHES Mount lift cylinders and assemble hose lines as shown in figures 19 and 20. the lift cylinders requires a restrictor valve on the tractor end. Thread this valve on with the arrow pointing back towards the cylinders as illustrated. NOTE: The hydraulic line leading from the rod-end of Fig. 19 Hydraulic Lift System - 16 ft.
SECTION 3 – SET-UP INSTRUCTIONS — SUPERHARROW Fig. 20 Hydraulic Lift System - 20 ft.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER Fig. 1 The machine should be placed in an area that allows ample room for assembly in field position (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. Refer to illustrations and parts listing on pages 8-2 through 8-20 and follow these steps when assembling. 16’ HITCH ASSEMBLY HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER Fig. 2 20’ HITCH ASSEMBLY Bolt the two A-frame sections of the hitch together, using eight 7/8” bolts and locknuts. NOTE: Since these larger pieces have a tendency to warp when welded, it may be necessary to pull the legs of the hitch together to match the center tube brackets. HITCH, HUBS AND WHEELS Mount axle plates with spindles down for 11L tires and with spindles up for 14L tires. Mount hitch wheels and tires and install hitch jack.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER Fig. 15 Lift Arms and Tine Tube Assembly LIFT ARMS, TINE TUBES AND TINES Referring to figures 15, 16 and 17, position all lift arms and secure in place with two 1/2 x 7-1/2” bolts, lockwashers and nuts. Lift arm spacing is determined by referring to legend and schematic of respective model represented in Fig. 17. NOTE: Special lift arms are used where hydraulic cylinders are located. These special lift arms are left or right handed (Fig.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER When center section tines are properly spaced and secured, install tube clamps to prevent tubes from moving from side to side. Position tube clamps by taking advantage of places where an S-tine serves the same purpose on the opposite side of lift arm. Four tube clamps are provided for each section. After all tines are mounted, install connecting levers and links, centering them between tines at location indicated on the schematics.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER Fig.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER 4-6
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER 4-7
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER HARROW SECTIONS Attach harrow sections with pull and lift chains as illustrated in Fig. 18. Assemble 5 bar section lever linkage as shown in Fig. 4 on Page 2-3.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER HYDRAULIC SYSTEMS FOR MACHINES WITH 16 OR 20 FT. HITCHES Mount lift cylinders and assemble hose lines as shown in figures 19 and 20. the lift cylinders requires a restrictor valve on the tractor end. Thread this valve on with the arrow pointing back towards the cylinders as illustrated. NOTE: The hydraulic line leading from the rod-end of Fig. 19 Hydraulic Lift System - 16 ft.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER Fig. 20 Hydraulic Lift System - 20 ft.
SECTION 4 – SET-UP INSTRUCTIONS — SUPERWEEDER HYDRAULIC DEPTH CONTROL The Superweeder Hydraulic Depth Control System requires one hydraulic cylinder per section to rotate S-tines up or down. Mount these cylinders on special lift arms as shown in figure 15. Assemble hose lines as shown in figure 22 and pages 4- 12 and 4-13. Each cylinder requires two hoses leading to the manifold mounted on the hitch crossmember.
SUPERWEEDER HYDRAULIC SYSTEM (25’-42’) f 180” 210” 230” 230” 230” 250” 290” 4-12 HOSE PART NO. 8N2050 8N2060 8N2076 8N2088 8N2150 8N2160 8N2170 8N2180 8N2190 8N2210 8N2230 8N2250 8N2290 *20’ Hitch Superweeders use 8N3252 (3/8”x252” Hyd.
SUPERWEEDER HYDRAULIC SYSTEM (47’-70’) a 50” 50” 76” 50” 50” 76” 76” 76” h 210” 230” 250” 210” 250” 290” 290” 290” i 88” 88” 88” 170” 110” 110” 170” 190” j 110” 110” 110” 180” 120” 120” 180” 210” HOSE PART NO.
NOTES 4-14
SECTION 5 – SET-UP INSTRUCTIONS CABLE AUTO-FOLD (16 Ft. Hitches) CABLE AUTO-FOLD (16 Ft. Hitches) SPRING ANCHOR BRACKETS Mount the spring anchor brackets (Ref. 16) to the outside of the hitch frame as shown in Fig. 28 and at a distance “A” as shown in Fig. 27. Note that latch spring mounting bracket (Ref. 11) also attaches with the two right front mounting bolts. Mount so the 3/8” dia. hole is up. Secure anchor brackets to the hitch frame with a mounting plate (Ref.
SECTION 5 – SET-UP INSTRUCTIONS CABLE AUTO-FOLD (16 Ft. Hitches) Fig. 27 Cable Auto-Fold Positioning (16 Ft. Hitch) Fig. 28 Assembly: Cable Auto-Fold (16 Ft.
SECTION 5 – SET-UP INSTRUCTIONS CABLE AUTO-FOLD (16 Ft. Hitches) Ref. Part No. Description Qty. 1 8D2100 CHAIN, 6 link 1 2 4 8D3152 8D4012 8D4020 U-BOLT, 1/2 x 3-3/8” (16’ New) CHAIN, 5/16” x 18 links - 16’ hitch CABLE, 1/4” x 13’ - 16’ hitch 2 2 1 5 8D4024 CABLE CLAMP, 1/4” 2 6 8D4026 CABLE THIMBLE, 1/4” 1 7 8D4030 LINK, cable and chain attach.
NOTES 5-4
SECTION 6 – SET-UP INSTRUCTIONS CABLE AUTO-FOLD (20 Ft. Hitches) CABLE AUTO FOLD, 20 Ft. Hitch Refer to Fig. 29 and follow these steps: 4” bolt and jamnut (Ref. 25 & 28) to provide clearance between the guide (A) and the hitch tube. Tighten 5/8” U-bolts on pivot mounting brackets when adjustments are complete. PIVOT MOUNTING BRACKETS AND CABLE FOLD ARMS Mount the left and right pivot mounting brackets to the outside of the hitch frame against the welded stops.
SECTION 6 – SET-UP INSTRUCTIONS CABLE AUTO-FOLD (20 Ft. Hitches) CABLE AUTO-FOLD ASSEMBLY (20 Ft. Hitch) Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 21A 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Part No.
SECTION 7 – OPERATION - ALL MACHINES 2. Insure that Transport Lock Pins are installed (See Fig. 30). 3. If hitch tongue is light, mount hitch jacks on wing tube before tractor is removed. (See Fig. 31 and Page 1-2 – Negative Hitch Weight Warning). Two wing tube jack brackets are standard on all Superweeders. The second wing tube jack bracket is optional on most CultiHarrows and Superharrows. Order PN 8C2280 for bracket and PN 8D0330 for mounting U-bolt.
SECTION 7 – OPERATION - ALL MACHINES Fig. 33 Teeth Set for Shallow Penetration Fig. 34 Teeth Set for Deep Penetration tions ride high on front, place top pull chain in bottom hole on lift arm bracket. If section rides low in front, place top pull chain in top hole on lift arm bracket. HARROW SECTION ADJUSTMENT Harrow sections should be attached to lift arms as shown in figure 3, page 2-3. To adjust sections for deep or shallow penetration, see figures 33 and 34.
SECTION 7 – OPERATION - ALL MACHINES USING THE SUPERWEEDER AS A HARROW ONLY To use your Summers Superweeder for pre-emergence chemical incorporation, (Example: Treflan incorporated over seeded wheat) simply fully extend the S-tine controlling cylinders. This will rotate S-tines completely out of the ground (6” ground clearance) and thus convert the Superweeder into a “straight harrow”. NEVER rotate S-tines forward or backward with machine in transport position.
SECTION 7 – OPERATION - ALL MACHINES MAINTENANCE AND SERVICE LUBRICATION Grease fitting locations and lube frequencies: Over Winter: Coat extended hydraulic cylinder rods with grease to prevent corrosion. Daily: Daily: Daily: Weekly: Weekly: TIRE INFLATION Listed below are recommended tire inflations: 2 on each knuckle 1 on hinged joint on hinged wing machines Auto-Fold pivots 1 on each transport wheel axle 1 on each pivot tube where center section attaches to hitch Periodic: Repack wheel bearings.
SECTION 8 – PARTS 16’ Hitch 8-2 16’ Hitch — Auto-Fold 8-3 16’ Hitch — Hydraulic System 8-4 16’ Hitch — Cable, Center and Wing Chart 8-5 20’ Hitch 8-6 20’ Hitch — Auto-Fold 8-7 20’ Hitch — Hydraulic Systems 8-8 20’ Hitch — Cable, Center and Wing Chart 8-9 Drawbar Centers and Wings 8-10, 8-11 (A)djustable (D)ouble (D)isk Drawbar 8-10, 8-11 Transport Axle 8-12 Cables and Pins 8-13 Superweeder Sections 8-14 Superweeder Hydraulics 8-15, 8-16 5 1/2’ 5 Bar 3/8” Tooth Section (8H0805)
SECTION 8 – PARTS HITCH ASSEMBLY — 16 FT. Ref. 1 2 3 4 5 6 7 8 9 10 11 Part No.
SECTION 8 – PARTS Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CABLE AUTO-FOLD ASSEMBLY (16 Ft. Hitch) Ref. Part No. Part No. 21 8R4190 - Selector Spring 8D2100 - Chain 6 Link 22 8R4335 - Eye Bolt 3/8" NC 8D3152 - U-Bolt 1/2x3-3/8x7-1/4" Sq 23 8R6145 - Eye Bolt 3/4" 8D4012 - 16 Ft. Chain 24 8X0034 - Bolt 7/16x1.75 w/1" Thread 8D4020 - 16 Ft.
SECTION 8 – PARTS HYDRAULIC SYSTEM — 16 FT. HITCH Ref. 1 2 3 4 5 6 7 8 9 10 11 12 Part No.
SECTION 8 – PARTS 16’ HITCH — 6” X 4” DRAWBAR Specification Chart Machine Size Cable Length PN-Cable Single CULTI-HARROW (3/8” Tooth) 25’ 33’ 39’ 42’ 44’ 53’ 55’ (Hinged Wing) Inside Outside 56’ 61’ 66’ (Hinged Wing) Inside Outside 67’ 67’ (Hinged Wing) Inside Outside 70’ 70’ (Hinged Wing) Inside Outside 77’ (Hinged Wing) Inside Outside 149” 193” 193” 193” 193” 246” 178” 262” 246” 246” 214” 324” 324” 178” 324” 324” 193” 324” 214” 370” 8D1800 8D1830 8D1830 8D1830 8D1830 8D1860 8D1820 8D1870 8D1860 8D18
SECTION 8 – PARTS HITCH ASSEMBLY — 20 FT. Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 8D1013A - 20' Hitch Front 8D1014 - 20' Hitch Rear 8D0720 - Hitch Piece Cast 8D0724 - Clevis Hitch (Optional) 8D6340 - Drop Axle Hitch w/Hardware 8D6350 - Spindle w/Plate Hitch for 611 Hub 8D6355 - Spindle w/611 Hub Hitch 8D3840 - Spindle w/Plate Hitch for 614 Hub 8D3845 - Spindle w/614 Hub Hitch See Hub Breakdown Page 10.
SECTION 8 – PARTS 7/13/03 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 CABLE AUTO-FOLD – (20 Ft. Hitch) Ref. Part No. Part No. 20 8R6145 - Eye Bolt 3/4" 8D2400 - Chain 3 Link .625" Dia. 21 8J5600 - 9/16”-18 ORB X #6 JIC(F-SW) 8D2410 - Chain 9 Link .625" Dia.
SECTION 8 – PARTS HYDRAULIC SYSTEM — 20 FT. HITCH Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 Part No.
SECTION 8 – PARTS 20’ HITCH — 6” X 4” DRAWBAR Specification Chart Machine Size Cable Length PN-Cable Single CULTI-HARROW (3/8” Tooth) 56’ 56' w/Auto-Fold 70' 70' w/Auto-Fold 70' (Hinged Wing) Inside Outside 70' (Hinged Wing) Inside w/Auto-Fold Outside 84' (Hinged Wing) Inside Outside 84' (Hinged Wing) Inside w/Auto-Fold Outside 98' (Hinged Wing) Inside Outside 98' (Hinged Wing) Inside w/Auto-Fold Outside 112' (Hinged Wing) Inside Outside 112' (Hinged Wing) Inside w/Auto-Fold Outside 324” 295" 383" 341"
SECTION 8 – PARTS 8-10
SECTION 8 – PARTS DRAWBAR CENTERS AND WINGS Ref. 1-5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Ref. Part No. See Chart Page 8-5 - 16’ Hitch 24 See Chart Page 8-7 - 20’ Hitch 25 8D0620 - Knuckle Cast w/Zerks 6x4 Drawbar 26 Trans. Whl Asmbly - See Page 8-12 27 Hub Asmbly - See Page 8-21 28 8D6351 - Spindle w/Plate Wing for 611 Hub 29 8D6356 - Spindle w/611 Hub Wing 30 8D3850 - Spindle w/Plate Wing for 614 Hub (opt.) 31 8D3855 - Spindle w/614 Hub Wing (opt.
SECTION 8 – PARTS TRANSPORT AXLE FOR H611 HUB (1 3/4” Dia. - Used 0n 1980 Models & Later) Ref. 1 2 3 4 5 6 7 8 9 10 Part No. 7D1145 - Bracket 1-3/4" Trans Axle 8X0361 - NR Mach Bushing 1.
SECTION 8 – PARTS CABLES AND PINS Ref. 1 Part No.
SECTION 8 – PARTS Ref. 1 2 3 4 5 6 7 8 9 10 11 SUPERWEEDER SECTIONS (3 Rank) 12 8X0031 - Bolt 7/16-14NCx1" Part No.
SUPERWEEDER HYDRAULIC SYSTEM (25’-42’) 25’, 29’, 33’, 35’, 39’ and 42’ Machines MACHINE HOSE LENGTHS SIZE a b c d e 25’ 50” 60” 150” 160” 170” 29’ 50” 60” 170” 180” 190” 33’ 50” 60” 190” 210” 210” 35’ 50” 60” 190” 210” 230” 39’ 50” 60” 210” 210” 230” 42’ 50” 60” 210” 230” 230” 42’ w/20’ Hitch 76” 88” 250” 250” 290” f 180” 210” 230” 230” 230” 250” 290” SECTION 8 – PARTS 8-15 HOSE PART NO.
SUPERWEEDER HYDRAULIC SYSTEM (47’-70’) MACHINE SIZE 47’ w/16’ Hitch 50’ w/16’ Hitch 50’ w/20’ Hitch 55’ w/16’ Hitch 56’ w/16’ Hitch 56’ w/20’ Hitch 58’ w/20’ Hitch 70’ w/20’ Hitch a 50” 50” 76” 50” 50” 76” 76” 76” 47’, 50’, 55’, 56’, 58’ and 70’ Machines HOSE LENGTHS b c d e f g 60” 24” 36” 180” 88” 110” 60” 24” 36” 210” 88” 110” 88” 24” 36” 210” 88” 110” 60” 24” 36” 190” 180” 190” 60” 24” 36” 230” 110” 120” 88” 24” 36” 230” 110” 120” 88” 24” 36” 210” 180” 190” 88” 24” 36” 230” 230” 230” h 210” 230” 250”
SECTION 8 – PARTS 7/15/03 5-1/2 FOOT HARROW SECTION - 5 BAR (8H0805) Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part No. 8H0410 - Side Angle Left 5 Bar 8H0411 - Side Angle Right 5 Bar 8H0370 - Flat 5/16x1.5 - 57" 8H0235 - Flat 5/16x1.5 - 49.5" 8H0260 - Flat 5/16x1.5 -18.5" Adj Culti 8H0631 - 1st Pipe w/Lever 5.5' 5 Bar 8H0632 - 2nd Pipe w/Lever 5.5' 5 Bar 8H0633 - 3rd Pipe w/Lever 5.5' 5 Bar 8H0634 - 4th Pipe w/Lever 5.5' 5 Bar 8H0635 - Rear Pipe w/Lever 5.
SECTION 8 – PARTS 8-18
SECTION 8 – PARTS 8-19
SECTION 8 – PARTS 8-20
HUB AND AXLE COMPONENTS Assembly Notes: A. Before towing machine, pack wheel bearings and fill 1/2 of hub cavity with high quality bearing grease. B. Tighten axle nut to 50 ft.-lbs, loosen nut until first slot is aligned with hole in axle, install cotter pin and bend to retain.
NOTES 8-22
Stock code Description Stock code Description 7C4020 7C4040 7C4050 7C4055 7C4060 7C4070 7D1107 7D1107S 7D1108 7D1108S 7D1145 8A4048 8A4050 8A4052 8C0050 8C0150 8C0200 8C0202 8C0204 8C0206 8C0250 8C0270 8C0432 8C0450 8C0532 8C0535 8C0650 8C0800 8C1410 8C1420 8C1430 8C1435 8C1452 8C1470 8C1480 8C1700 8C1710 8C1720 8C1740 8C1750 8C1755 8C1760 8C1780 8C1800 8C1800D 8C1802 8C1802D 8C1805 8C1900 8C1920 8C1940 8C1950 8C1970 8C2200 8C2210 8C2246 8C2260 8C2270 8C2280 8C2300 8C2300H 8C2310 8C2310H 8C2316 8C2318 8C2
Stock code Description Stock code Description 8C5280 8C5300 8C5310 8C5370 8C5402 8C5412 8C5500 8C5510 8C5600 8C5650 8C5805 8C5807 8C5820 8C5910 8C5920 8C5980 8C6000 8C6010 8C6012 8C6015 8C6110 8C6120 8D0110 8D0112 8D0200 8D0300 8D0302 8D0310 8D0312 8D0327 8D0330 8D0340 8D0350 8D0490 8D0520 8D0620 8D0675 8D0677 8D0702 8D0704 8D0706 8D0720 8D0722 8D0724 8D0730 8D0750 8D1010 8D1013A 8D1014 8D1022 8D1024 8D1028 8D1029 8D1030 8D1031 8D1032 8D1033 8D1036 8D1040 8D1042 8D1062 8D1065 8D1075 8D1080 8D1081 8D1090 8
Stock code Description Stock code Description 8D3042 8D3045 8D3046 8D3047 8D3048 8D3049 8D3050 8D3051A 8D3053 8D3095 8D3096 8D3097 8D3097A 8D3098 8D3099 8D3100 8D3100A 8D3101 8D3102 8D3107 8D3108 8D3110 8D3130 8D3140 8D3150 8D3152 8D3212 8D3800 8D3830 8D3840 8D3845 8D3850 8D3855 8D4010 8D4012 8D4018 8D4020 8D4024 8D4026 8D4030 8D4040 8D4050 8D4110 8D4120 8D4130 8D4140 8D4150 8D4160 8D4170 8D4200 8D4202 8D4210 8D4220 8D4222 8D4230 8D4232 8D4250 8D5110 8D5111 8D5112 8D5113 8D5114 8D5117 8D5118 8D5120 8D5210
Stock code Description Stock code Description 8D9120 8D9121 8D9122 8D9130 8D9138 8D9140 8D9146 8D9160 8D9180 8D9186 8D9192 8D9211 8D9213 8D9214 8D9215 8D9216 8D9217 8D9217A 8D9217B 8D9218 8D9218A 8D9220 8D9224 8D9226 8D9230 8D9232 8D9234 8D9236 8D9240 8D9250 8D9260 8D9316 8D9318 8D9318A 8D9326 8D9330 8D9330A 8D9332 8D9332A 8D9334 8D9340 8D9340B 8D9350 8D9358 8D9360 8D9416 8D9418 8D9418A 8D9420 8D9424 8D9426 8D9430 8D9432 8D9434 8D9436 8D9440 8D9450 8D9458 8D9466 8D9470 8D9472 8D9473 8D9474 8D9475 8D9476 8
Stock code Description Stock code Description 8H1380 8H1382 8H1384 8H1385 8H1395 8H1398 8H1480 8H1498 8H1499 8H1502 8H1504 8H1506 8H1510 8H1512 8H1520 8H1522 8H1530 8H1532 8H1540 8H1541 8H1546 8H1550 8H1560 8H2010 8H2040 8H2042 8H2044 8H2045 8H2060 8H2062 8H2064 8H2065 8H2076 8H2078 8H2079 8H2086 8H2088 8H2089 8H2094 8H2096 8H2098 8H2099 8H2100 8H2107 8H2108 8H2114 8H2120 8H2130 8H2132 8H2142 8H2144 8H2145 8H2150 8H2155 8H2160 8H2170 8H2180 8H2190 8H2300 8H2310 8H2314 8H2315 8HD0060 8HD0064 8HD0080 8HD015
Stock code Description Stock code Description 8HD5190 8HD5225 8HD5230 8HD5240 8HD6110 8HD6120 8HD6120S 8HD6140 8HD6150 8HD6160 8HD6170 8HD6174 8HD6176 8HD6180 8HD6182 8HD6460 8HD6464 8HD6490 8HD6620 8HD6640 8HD6660 8HD6660H 8HD6663 8HD6664 8HD6665 8HD6680 8HD6684 8HD6685 8HD6698 8HD7000 8HD7020 8HD7040 8HD7060 8HD7080 8HD7100 8HD7110 8HD7120 8HD7130 8HD7136 8HD7148 8HD7160 8HD7172 8HD7184 8J0190 8J0200 8J1022 8J1023 8J1027 8J3010 8J3246 8J3256 8J3266 8J3276 8J4000 8J4015 8J4020 8J4030 8J4032 8J4040 8J4042
Stock code Description Stock code Description 8K1532 8K1540 8K1610 8K1620 8K1640 8K1660 8K1680 8K1682 8K1682C 8K1683 8K1684 8K1900 8K1920 8K2000 8K2020 8K2050 8K2080 8K2090 8K2102 8K2104 8K2120 8K2130 8K2140 8K2150 8K2160 8K2170 8K3001 8K3002 8K4000 8K4009 8K4010 8K4019 8K4020 8K4130 8K4200 8K4210 8K4300 8K4392 8K4400 8K4410 8K4420 8K4430 8K4449 8K4450 8K4610 8K4620 8K4630 8K4640 8K4650 8K4660 8K4670 8K4690 8K4692 8K4698 8K4700 8K4710 8K5024 8K5024C 8K5026 8K5200 8K5210 8K5214 8K5350 8K5505 8K5515 8K5520
Stock code Description Stock code Description 8K8445C 8K8452 8K8452C 8K8455 8K8460 8K8520 8K8530 8K8540 8K8560 8K8600 8K8608 8K8610 8K8620 8K8630 8K8640 8K8642 8K8650 8K8660 8K8710 8K8720 8K8730 8K8732 8K8734 8K8736 8K8750 8K8770 8K8774 8K8776 8K8778 8K8782 8K8786 8K8790 8K8792 8K8810 8K8814 8K8816 8K8818 8K8822 8K8826 8K8830 8K8832 8K8856 8K8858 8K8960 8K9084 8K9090 8K9102 8K9104 8K9106 8K9160 8K9162 8K9164 8K9174 8K9176 8K9178 8K9180 8K9190 8K9220 8K9230 8K9375 8K9400 8K9425 8K9450 8K9475 8K9500 8K9640
Stock code Description Stock code Description 8R6852 8R6853 8R6854 8R6855 8R6856 8R6857 8R6858 8R6859 8R6860 8R6861 8R6864 8R6866 8R6867 8R6868 8R6898 8R6899 8R6900 8R6901 8R6902 8R6911 8R6913 8R6914 8R6917 8R6920 8R6921 8R6922 8R6923 8R6924 8R6925 8R6927 8R6942 8R6944 8S0072 8S0074 8S0075 8S0080 8S0250 8S0280 8S0290 8S0295 8S0300 8S0310 8S0315 8S0319 8S0320 8S0330 8S0340 8S0345 8S0350 8S0360 8S1120 8S1124 8S1126 8S1420 8S1430 8S2980 8S2990 8T0100 8T0400 8T0500 8T0549 8T0550 8T0600 8T0606 8T0608 8T1004 8T
Stock code Description Stock code Description 8T4300 8T4325 8T4350 8T4380 8T4400 8T4410 8T4510 8T4520 8T4530 8T4540 8T4550 8T5000 8T5020 8T5049 8T5050 8T5150 8T5200 8T5345 8T6000 8T6010 8T6020 8T6810 8T7020 8W0115 8W0200 8W0240 8W0250 8W0950 8W1002 8W1005 8W1006 8W1007 8W1011 8W1012 8W1015 8W1016 8W1018 8W1020 8W1021 8W1022 8W1023 8W1039 8W1040 8W1041 8W1100 8W1104 8W1106 8W1110 8W1120 8W1130 8W1136 8W1140 8W1142 8W1150 8W1152 8W1160 8W1162 8W1200 8W1204 8W1210 8W1220 8W1221 8W1222 8W1224 8W1226 8W1228 8W
Stock code Description Stock code Description 8X0015 8X0016 8X0017 8X0018 8X0019 8X0020 8X0021 8X0021A 8X0021B 8X0022 8X0023 8X0024 8X0026 8X0027 8X0028 8X0029 8X0030 8X0031 8X0033 8X0034 8X0035 8X0036 8X0037 8X0038 8X0041 8X0044 8X0045 8X0046 8X0047 8X0048 8X0049 8X0060 8X0061 8X0062 8X0063 8X0064 8X0065 8X0066 8X0066S 8X0067 8X0068 8X0069 8X0070 8X0071 8X0072 8X0073 8X0074 8X0075 8X0076 8X0077 8X0078 8X0079 8X0080 8X0081 8X0082 8X0083 8X0084 8X0085 8X0086 8X0087 8X0090 8X0091 8X0092 8X0093 8X0094 8X0095
Stock code Description Stock code Description 8X0240 8X0242 8X0246 8X0250 8X0251 8X0252 8X0253 8X0254 8X0255 8X0257 8X0258 8X0259 8X0260 8X0261 8X0262 8X0263 8X0264 8X0267 8X0268 8X0269 8X0270 8X0277 8X0278 8X0279 8X0280 8X0281 8X0282 8X0283 8X0284 8X0285 8X0286 8X0287 8X0288 8X0289 8X0290 8X0292 8X0299 8X0300 8X0301 8X0302 8X0303 8X0304 8X0305 8X0306 8X0307 8X0308 8X0309 8X0311 8X0312 8X0313 8X0314 8X0315 8X0316 8X0317 8X0318 8X0319 8X0320 8X0321 8X0322 8X0323 8X0324 8X0325 8X0326 8X0327 8X0328 8X0328H 8
Stock code Description 8Z0232 8Z0276 8Z0278 8Z0285 8Z0340 8Z0342 8Z0344 8Z0346 8Z0348 8Z0800 8Z0805 8Z0810 8Z1070 8Z1088 8Z1089 8Z1090 8Z1096 8Z1098 8Z1100 8Z1101 8Z1102 8Z1105 8Z1129 Stock code Description AUTO FOLD WARNING DECAL 2 X 7" GENERAL CAUTION DECAL 91WHEEL TIGHTENING DECAL 96DAILY MAINTENANCE DECAL 96REPHASING CYLINDERS DECAL INSTALL CYL LOCKS DECAL WING DANGER DECAL ELECTROCUTION-TILL DECAL GAUGE WHEEL DEPTH DECAL REFLECTOR AMBER ADHSV-BCK 98REFLCTR REDORANGE ADHSV-BK 99REFLECTOR RED ADHSV-BCK
