22’ HITCH IMPLEMENTS Operator’s Manual SUPERHARROW PLUS SUPERHARROW 2650 HARROWPACKER 22’ HITCH IMPLEMENTS 3/8” and 9/16” Diameter Tooth Sections 4-RANK SUPERWEEDER IMPORTANT THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE. MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. See www.summersmfg.com for the latest version of all Summers Operator’s Manuals. SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.
Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 12 months from the date of purchase by the end user from Summers’ dealer.
INTRODUCTION This manual provides information about Safety, Assembly, Operation and Parts for the Summers Superharrow PLUS, Superharrow 2650, Harrow Packer and 4-Rank Superweeder featuring the Summers 22 Ft. Hitch. Reference to “right” and “left” in this book is determined when the machine is viewed from the rear. Parts are referenced in each drawing with the Summers Manufacturing Part Number. Use this Part Number when ordering replacement parts from your Summers dealer.
TABLE OF CONTENTS SECTION 1: SAFETY: ALL MACHINES Safety-Alert Symbol & General Safety Practices...................................................... 1-1, 1-2 Safety Decals & Reflectors....................................................................................... 1-3 - 1-7 General Assembly Safety Practices.................................................................................. 1-8 SECTION 2: ASSEMBLY & OPERATION: SUPERHARROW PLUS Set-Up Instructions and Parts.............................
SECTION 1 - SAFETY SAFETY-ALERT SYMBOL This symbol is used to denote possible danger and care should be taken to prevent bodily injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.
SECTION 1 - SAFETY SAFETY DURING TRANSPORT 1. ONLY TOW at a safe speed. Use caution when making corners or meeting traffic. 2. USE a safety chain between tractor drawbar and implement hitch when transporting on public roads. 3. ALWAYS use transport locks when transporting on public roads. 4. COMPLY with local lighting, marking and maximum width regulations when transporting on highways. 5. FREQUENTLY CHECK for traffic from rear, especially during turns. WARNING IMPORTANT INFORMATION ON 22 FT.
SECTION 1 - SAFETY SAFETY DECALS 1. KEEP SAFETY DECALS AND REFLECTORS CLEAN. 2. REPLACE missing or unreadable decals. New decals are available from your Summers dealer by stating correct part number (PN) located in lower right hand corner. 1. TRANSPORT LOCK DECAL (PN 8Z0075). 2. HITCH WARNING DECAL (PN 8Z0092). 3. AUTO-FOLD WARNING DECAL (PN 8Z0093).
SECTION 1 - SAFETY 4. AUTO-FOLD ARM WARNING DECAL (PN 8Z0232). 5. GENERAL CAUTION DECAL (PN 8Z0276). 6. CYLINDER LOCKS DECAL (PN 8Z0342).
SECTION 1 - SAFETY 7. WING DANGER DECAL (PN 8Z0344). 8. ELECTROCUTION DANGER DECAL (PN 8Z0346). 9. PINCH POINT DECAL (PN 8Z0087).
SECTION 1 - SAFETY 10. AMBER REFLECTOR (PN 8Z0800). 11. RED-ORANGE REFLECTOR (PN 8Z0805). 12. RED REFLECTOR (PN 8Z0810). SAFETY LIGHT OPERATION The Summers Safety Light Kit is equipped with a 7 pin connector which meets SAE J560 specification. To protect 7 pin connector, store in dust cap (8K8067) when not attached to towing vehicle.
SECTION 1 - SAFETY 1-7
SECTION 1 - SAFETY GENERAL ASSEMBLY SAFETY PRACTICES YOU ARE RESPONSIBLE for the safe assembly of the machine. BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking. DO NOT ALLOW CHILDREN or other unauthorized persons within the assembly area. ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear. WEAR PERSONAL PROTECTIVE EQUIPMENT which includes a hard hat, eye protection, work gloves and steel toed boots with slip resistant soles.
SECTION 2 - SUPERHARROW PLUS SET-UP INSTRUCTIONS Fig. 1: Field Position Fig. 2: Transport Position The machine should be placed in an area that allows ample room for assembly in field position (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. HITCH – Axles, Wheels and Jack Attach hitch hydraulic depth adjustment and axle assemblies as shown on page 2-2 through page 2-5. Mount hitch wheels and tires and install hitch jack.
2-2 8D0720 8X0309 1" LW 8X0280 8X0281 NY-LOCK 1" 8X0223 1/4" FN 8K8067 8D8490 8X0000 1/4 X 3/4" 8X0140 1 X 7" 8D8500 8X0110 3/4 X 1-1/4" SEE AUTO-FOLD ASSEMBLY 8X0246 1/2" FN 8Z1000 8D2460 8X0318 3/4" FW 8W1204 1/2 X 3 X 3" 8T4385 8A1004 5" HC 8C2660 22' MACHINE HITCH NOTE: CUSHIONS CAN BE ADDED TO DECREASE HOLE SIZE.
8X0260 3/4" N 8W1862 8X0306 3/4" LW 8W1860 2-3 8W1886 8X0121 3/4" X 6-1/2" 8X0092 5/8" X 2-3/4" 8R6065 W/ZERK 8R6060 8W1850 8T3300 8R6067 8X0327 1 1/4" FW 8C2325 8X0261 3/4" LN 8W1884 L 2.5 x 2.5 x 3/8 8X0115 3/4 X 3-1/2" 8R6810 SS BUSH 8X0304 5/8" LW 8X0250 5/8" N 8X0260 3/4" N 1/13/2014 8X0115 3/4 X 3-1/2" 8W1890 8X0265 3/4" LN DETAIL A SCALE 0.08 : 1 8X0070 1/2 X 3-1/4" 8K1100 8X0281 NY-LOCK 1" 8X0316 1" FW 9HD0880.
2-4 8D2400 8D2730 8X0318 3/4" FW 8C2650 8D2730 8C2690 8D0312 8X0414 8C1920 (DUAL CABLE ONLY) 8X0281 NY-LOCK 1" 8X0261 3/4" LN 8C1900 8X0414 8C2690 8D0312 AUTO-FOLD 4" <2 > E ID S IN m TO imu 8S1076 K x a O HO 47" m E D SI IN 8X0150 1" X 20" 8X0261 3/4" LN 1/2/2014 8X0330 1/2" FW 8R6145 8C1940 8X0063 1/2 X 1-1/2" SEE CABLE CHART FOR CABLE LENGTH AND PART NUMBER 8C2600 8C1760 3/4 X 8-1/16 X 6" 8C1470 9HD0880.
SECTION 2 - SUPERHARROW PLUS DRAWBAR ASSEMBLY 8X0307 7/8" LW 8X0286 1 1/2" JN 8X0268 7/8" N 8X0242 NY-LOCK 1/2" N 8X0211 5/16" FN 8X0203 3/8" FN 8C2280 8S1126 8D8522 8X0068 1/2 X 2.
SECTION 2 - SUPERHARROW PLUS 2-6
2-7IN 8J5510 3/4”-16ORB X #6JIC(M) STR 8N3252 NYL.
SECTION 2 - SUPERHARROW PLUS SET BOLTS FOR AUTO FOLD ARM ADJUSTMENT 8X0259 3/4” JN 8X0112 3/4”X2-1/4” 8” SQUARE DRAWBAR SPECIFICATION CHART Machine Size Cable Length PN-Cable SUPERHARROW PLUS PN-Wing PN-Hinged (Hngd Wing - Wing - Right Left Part 1) Part 1 PN-Hinged Wing - End PN-Lift Cylinder 36’ (Solid Wing) 246” 8D1860 8HD6620 8C0432 48’ (Solid Wing) 281” 8D1880 8HD6640 8C0432 60’ (Solid Wing) 324” 8D1900 8HD6660 8C0432 60’ (Hinged Wing)Inside 246” 8D1860 8HD6663 Outsid
SECTION 2 - SUPERHARROW PLUS 2-9
SECTION 2 - SUPERHARROW PLUS Fig. 3: Rear Hitch View Fig. 3A: Left Knuckle SECTIONS: Attach sections to drawbar using 7/8” U-bolts and hardware provided. Position lift arms with following dimensions: Distance from drawbar center to centerline of first lift arm on either side is 24”. Distance between centerlines of lift arms on sections is 24”. Distance between centerlines of lift arms between sections is 48”.
SECTION 2 - SUPERHARROW PLUS Wing Section Lower Stop Bolt Location Center Section Stop Bolt Location (shown installed) Fig. 8 The two front outside teeth on the center section (closest to knuckles) must be secured with PN 8HD6150 (ANGLE, tooth stop) and 1/2” X 3-3/4” cap screws as shown in Fig. 9. This prevents interference in transport position. TRANSPORT WHEELS Locate transport wheel assemblies over end harrow section on 36 through 60 ft. machines with pivot tube in higher position.
2-12 8HD0510 8X0265 8X0118A 8HD0550 8X0242 8X0062 8X0330 8HD6200L 8X0242 8HD0532 8X0064 8HD0064 8HD0591L 8H1190S 8X0078 8X0062 8HD0080 8HD6140 8HD6180 8W1204 1 1 1 1 2 2 4 6 8HD0594L 8HD0595L 8HD6110 8HD6140 8HD6180 8W1204 8X0062 8 8X0303 2 8 8X0265 8X0330 37 8X0242 8 1 8HD0593L 8 1 8HD0592L 8X0240 2 8HD0591L 8X0118A 1 8HD0550 1 1 8HD0540 30 4 8HD0532 8X0078 2 8HD0510 PN 8HD0591L 8HD0592L 8HD0593L 8HD0594L 8HD0595L Distance 17 1/2" 22" 15 1/4" 19 3/4" 13" Lev
SECTION 2 - SUPERHARROW PLUS 2-13
SECTION 2 - SUPERHARROW PLUS 2-14
SECTION 2 - SUPERHARROW PLUS INSTALLATION INSTRUCTIONS 8C2270 - CABLE GUIDE BRACKET 72’ & 84’ SUPERHARROW PLUS Parts required for installation: Qty 2 2* 4* 4 PN 8C2270 8X0113 8X0123 8X0317 Description Cable Guide Bracket Bolt 3/4” x 5” (Use without Hyd. Tine Angle Pivot Bracket) Bolt 3/4” x 5-1/2” (Use with Hyd. Tine Angle Pivot Bracket) 3/4” Flat Washer Refer to the photos below to install the cable guides. The guides must be mounted on the top outside of the first mounting bracket on each wing.
SECTION 2 - SUPERHARROW PLUS Procedure to mount Hydraulic Tine Angle Adjustment Option Summers Mfg. recommends mounting the hydraulic tine angle adjustment option on the Superharrow Plus while machine is in transport position. The following instructions and photos refer to machine in transport position. Reference to left and right are determined when machine is viewed from the rear. 1.
SECTION 2 - SUPERHARROW PLUS 5. Mount cylinder attach brackets (8HD7020) onto 8” SQ drawbar using same set of holes used to attach the harrow section to 8” SQ tube. Locate center cylinder attach bracket at exact center of machine. Locate wing cylinder attach at locations shown in hydraulic tine angle layout drawing. Route hydraulic hoses as shown in photos. NOTE: Hydraulic Tine Angle Option can be used in upper three manual height adjustment settings ONLY.
2-18 8HD7110 8X0303 1/2" LW 8X0260 3/4" N 8X0240 1/2" N 8X0306 3/4" LW DETAIL A SCALE 1 / 9 8R6145 8X0259 3/4" JN 8X0253 NY-LOCK 5/8"-11NC A 8X0260 3/4" N 8X0306 3/4" LW 8X0116 3/4" X 6" 8HD7080 8HD7040 8K5515 3/4 X 4-1/16 X 6" 8C1780 8K5515 8X0307 7/8 X 8-1/16 X 10" 8S0340 8HD7110 3/4 X 4-1/16 X 6" 7/8" LW 1/2 X 4 X 5 1/4" SQ 8X0093 8HD7060 5/8" X 2" 8X0268 7/8" N 8HD7020 8K9102 8D9108 1/4 X 2" RP 8X0260 3/4" N 8K8435 (3-1/2") 8K8440c (4") 8K8445C (4-1/2") 8HD7130 (54") 8HD7136 (84"
SECTION 2 - SUPERHARROW PLUS 6. Remove existing front 3/4” X 5” bolts from inside mounting bracket on right hand section on the center of machine and secure spring flat to prevent movement. Install rock shaft bushing (8HD7000) on section mounting bracket using 3/4” X 5-1/2” bolts provided. Insert center rock shaft (8HD7130) into bushing, slide second bushing on rock shaft and secure this bushing on inside mounting bracket of left hand center section.
SECTION 2 - SUPERHARROW PLUS 9. After installing all lower bolts, remove existing upper bolts. Further elevate rock shaft and insert top 3/4” X 5-1/2” bolts. On right hand side of Superharrow Plus, position rock shaft so it extends 1” ahead of first bushing next to wing tube knuckle. On left hand side of machine, rock shaft needs to extend 4-1/4” ahead of first bushing next to wing tube knuckle. 10.
SECTION 2 - SUPERHARROW PLUS 11. Tighten all mounting hardware. Insure all three hydraulic cylinders are fully retracted. Adjust eye bolts to line up with clevis in levers. Secure eye bolts to levers with 5/8 X 2” bolts and locknuts. Tighten locknuts until they contact lever clevis flat.
SECTION 2 - SUPERHARROW PLUS 2-22
SECTION 2 - SUPERHARROW PLUS 12. Install hydraulic fittings and hoses as shown in hydraulic hose layout drawing (Page 2-22). Secure hoses next to existing hydraulic hoses on drawbar and hitch with clamps and nylon ties provided. Allow ample hose at hinge points to avoid pinching or stretching when folding and unfolding machine. Route hose through loop at rear of hitch to prevent ground contact in transport position. The Hydraulic Tine Angle option utilizes a master – slave hydraulic system.
SECTION 2 - SUPERHARROW PLUS 13. IMPORTANT: BEFORE ACTIVATING HYDRAULIC CYLINDERS, DISCONNECT EXISTING PINS USED FOR TINE ANGLE ADJUSTMENT. a. Remove roll pin from 5/8” diameter pin. b. Remove 5/8” pin, spring and washer from section. 14. Install hydraulic tips. 15. Initial Start-Up for HTA hydraulic cylinders: Hydraulic cylinders for the HTA option should not be charged with oil until machine is lowered into field position.
SET BOLTS FOR AUTO FOLD ARM ADJUSTMENT SEE PAGE 2-8 SECTION 2 - SUPERHARROW PLUS 2-25
SECTION 2 - SUPERHARROW PLUS 2-26
2-27 8Z0092 HITCH WARNING 8Z0276 GENERAL CAUTION 12/17/2013 8Z0204 5.5" SUMMERS DECAL 8Z0093 AUTO-FOLD LOCK WARNING 8Z0346 ELECTROCUTION DANGER 8Z0232 AUTO-FOLD WARNING 8Z0075 TRANSPORT LOCK DECAL DECALS 8C2200.
SECTION 2 - SUPERHARROW PLUS OPERATING INSTRUCTIONS TRANSPORT TO FIELD POSITION 1. Hitch machine to tractor drawbar using a locking pin and safety chain. Connect hydraulic hoses and wiring. Retract jacks and rotate into storage position 2. Select level area to lower machine into field position. 3. IMPORTANT: Remove transport locks. Store locks in storage guide shown in Figure 10. Fig. 10: Transport Lock in Locked Position 4. Back up machine slowly, maneuvering so wings open evenly.
SECTION 2 - SUPERHARROW PLUS SECTION ADJUSTMENT Section down pressure can be increased or decreased hydraulically by adjusting lift cylinders and manually by adjusting the lift cylinder adjustment bolt (8K1720, Page 2-2). Down pressure on wing sections can be increased by replacing the top spacer tubes (8HD0510) with extra pressure spacer tubes (8HD0520). Lower stop bushings can also be replaced with 8HD0520 to adjust individual sections so the machine raises more evenly.
SECTION 2 - SUPERHARROW PLUS NOTE: Hydraulic Tine Angle option can be used in upper three manual height adjustment settings ONLY. (See page 2-10). FIELD TO TRANSPORT POSITION 1. Stop in a level area and back tractor up to provide slack in pull cables. 2. Open manual lock valve on auto-fold lock cylinder. Fully extend auto-fold lock cylinder. 3. Fully retract Hydraulic Depth Adjust cylinders. 4. Fully retract lift cylinders raising sections. 5.
SECTION 2 - SUPERHARROW PLUS Spring Seedbed Preparation Suggested settings and adjustments for Spring Seedbed Preparation with the Summers SH+. IMPORTANT: SH+ sections are designed to run level insuring that all teeth work at the same depth. If rear of section is running higher than the front, the section is incorrectly adjusted and component failure may occur. Summers products are NOT warranted for damage caused by improper adjustment a. Extend hydraulic depth adjustment cylinders 1/2 way.
SECTION 2 - SUPERHARROW PLUS MAINTENANCE AND SERVICE Daily Maintenance: Check all wheel and frame bolts for tightness. Daily Greasing: Two zerks on each knuckle. One zerk on each transport axle pivot. Two zerks on each cable auto-fold arm. Two zerks on hitch hydraulic depth adjustment – pillow block casting (8R6065, page 2-3). 60-84 ft. with hinged wing only: One zerk on each Hinged Wing Pivot. Weekly Maintenance: Inspect wheel bearings for tightness.
SECTION 3 - SUPERHARROW 2650 SET-UP INSTRUCTIONS Fig. 1: Field Position Fig. 2: Transport Position The machine should be placed in an area that allows ample room for assembly in field position (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. Refer to illustrations and parts listing and follow these steps when assembling. HITCH – Axles, Wheels and Jack Attach hitch hydraulic depth adjustment and axle assemblies as shown on pages 3-2 through 3-4.
3-2 8D0720 8X0309 1" LW 8X0280 8X0281 NY-LOCK 1" 8X0223 1/4" FN 8K8067 8D8490 8X0000 1/4 X 3/4" 8X0140 1 X 7" 8D8500 8X0110 3/4 X 1-1/4" SEE AUTO-FOLD ASSEMBLY 8X0246 1/2" FN 8Z1000 8D2460 8X0318 3/4" FW 8W1204 1/2 X 3 X 3" 8T4385 8A1004 5" HC 8C2660 22' MACHINE HITCH NOTE: CUSHIONS CAN BE ADDED TO DECREASE HOLE SIZE.
8X0260 3/4" N 8W1862 8X0306 3/4" LW 8W1860 3-3 8W1886 8X0121 3/4" X 6-1/2" 8X0092 5/8" X 2-3/4" 8R6065 W/ZERK 8R6060 8W1850 8T3300 8R6067 8X0327 1 1/4" FW 8C2325 8X0261 3/4" LN 8W1884 L 2.5 x 2.5 x 3/8 8X0115 3/4 X 3-1/2" 8R6810 SS BUSH 8X0304 5/8" LW 8X0250 5/8" N 8X0260 3/4" N 1/13/2014 8X0115 3/4 X 3-1/2" 8W1890 8X0265 3/4" LN DETAIL A SCALE 0.08 : 1 8X0070 1/2 X 3-1/4" 8K1100 8X0281 NY-LOCK 1" 8X0316 1" FW 9HD0880.
3-4 8D2400 8D2730 8X0318 3/4" FW 8C2650 8D2730 8C2690 8D0312 8X0414 8C1920 (DUAL CABLE ONLY) 8X0281 NY-LOCK 1" 8X0261 3/4" LN 8C1900 8X0414 8C2690 8D0312 AUTO-FOLD 4" <2 > E ID S IN m TO imu 8S1076 K x a O HO 47" m E D SI IN 8X0150 1" X 20" 8X0261 3/4" LN 1/2/2014 8X0330 1/2" FW 8R6145 8C1940 8X0063 1/2 X 1-1/2" SEE CABLE CHART FOR CABLE LENGTH AND PART NUMBER 8C2600 8C1760 3/4 X 8-1/16 X 6" 8C1470 9HD0880.
SECTION 3 - SUPERHARROW 2650 DRAWBAR ASSEMBLY 8X0307 7/8" LW 8X0286 1 1/2" JN 8X0268 7/8" N 8X0242 NY-LOCK 1/2" N 8X0211 5/16" FN 8X0203 3/8" FN 8C2280 8S1126 8D8522 8X0068 1/2 X 2.
SECTION 3 - SUPERHARROW 2650 8C1452 1 X 6 1/2” PIN 8X0414 CTR PIN 8C2246 8J6010 8J6010 3/4”-16ORB X #6JIC(M) 90° ADP 3/4”-16ORB X #6JIC(M) 90° ADP 8X0418 8X0414 CTR PIN 8C1420 1 X 5 7/8” PIN 5/16” CTR PIN 8C1452 1 x 6 1/2” PIN 8N3048 3/8 X 48” HH 8J6010 8N3124 3/4”-16ORB X #6JIC(M) 90° ADP 3/8 X 124” HH 8C2246 8X0418 RESTRICTOR VALVE 8J7116 ASSEMBLY 3/4”-16ORB X 3/4”-16ORB 1-WAY 1/16” RESTR 8J5510 3/4”-16ORB X #6JIC(M) STR CTR PIN 8N3096 3/8 X 96” HH 8N3018 8C0432 8C0532 - 3/8 X
SECTION 3 - SUPERHARROW 2650 SET BOLTS FOR AUTO FOLD ARM ADJUSTMENT 8X0259 3/4” JN 8X0112 3/4”X2-1/4” 22’ HITCH — 8” SQUARE DRAWBAR Specification Chart Machine Size Cable Length PN-Cable PN-Wing (Hngd Wing - Left Part 1) PN-Lift Cylinder SUPERHARROW 2650 56’ 324” 8D1900 262” 8D1870 Outside 88’ Inside 370” 8D1920 262” 8D1870 Outside 383” 8D1930 72’ Inside 3-7 8HD6650 (20’11”) 8C3300 (28’11”) 8HD6682 (36’11”) 8C0432 8C0432 8C0432
SECTION 3 - SUPERHARROW 2650 3-8
3-9 8HD0160 8HD0150 8X0242 8HD0550 DETAIL A SCALE 1/6 8HD6140 8X0520 8X0323 8HD8250 8HD0080 8HD0510 8HD0540 8X0242 8X0265 8HD0532 8X0064 8HD0064 8X0242 8X0062 8X0330 8X0118A 8HD8400 8X0078 8X0072 8X0242 8X0242 A 1/13/2014 8H1184S 8HD8255 1 1 1 1 1 6 1 8HD8255 8HD8260 8HD8265 8HD8270 8X0062 8X0064 8 1 2 1 8X0265 8X0323 8X0330 8X0520 PN 8HD8270 8HD8265 8HD8260 8HD8255 8HD8250 Distance 22" 15 1/2" 19 3/4" 13 1/4" 17 3/4" Lever to End of Pipe Distance 8 52 8X0118A 8X0242 5
SECTION 3 - SUPERHARROW 2650 Fig. 3: Rear Hitch View Fig. 3A: Right Knuckle SECTIONS: Attach sections to drawbar using 7/8” U-bolts and hardware provided. Position lift arms with following dimensions: Distance from drawbar center to centerline of first lift arm on either side is 24”. Distance between centerlines of lift arms is 48”. To compensate for various soil conditions and tooth wear, the sections can be mounted in four different positions as shown in the following chart and (Fig. 4 to 7).
SECTION 3 - SUPERHARROW 2650 Wing Section Lower Stop Bolt Location Center Section Stop Bolt Location (shown installed) Fig. 8 The two front teeth on the wing (closest to knuckles) must be secured with PN 8HD6150 (ANGLE, tooth stop) and 1/2” X 3-3/4” cap screws as shown in Fig. 9. This prevents interference in transport position. TRANSPORT WHEELS Locate transport wheel assemblies over end harrow section on 56 ft. machine with pivot tube in higher position.
SECTION 3 - SUPERHARROW 2650 INSTALLATION INSTRUCTIONS 8C2270 - CABLE GUIDE BRACKET 72’ & 88’ SUPERHARROW 2650 Parts required for installation: Qty 2 2* 4* 4 PN 8C2270 8X0113 8X0123 8X0317 Description Cable Guide Bracket Bolt 3/4” x 5” (Use without Hyd. Tine Angle Pivot Bracket) Bolt 3/4” x 5-1/2” (Use with Hyd. Tine Angle Pivot Bracket) 3/4” Flat Washer Refer to the photos below to install the cable guides. The guides must be mounted on the top outside of the first mounting bracket on each wing.
SECTION 3 - SUPERHARROW 2650 670" 24" 48" 48" * 274 1/2" 291 1/2" NOTE: DIMENSIONS SHOWN ARE APPROXIMATE. CABLE ATTACH BRACKETS SHOULD BE POSITIONED SO WING TUBES ARE LEADING BY 2°. *CONNECT REAR CABLES (8D1760) AT CENTER OF MACHINE WITH FOLLOWING HARDWARE: QTY. PN DESCRIPTION 1 8X0111 BOLT 3/4-10NC X 2-1/2" GR5 YZ 2 8X0318 WASHER 3/4" FLAT YZ 1 8X0261 NUT 3/4"-10NC NY-LOCK GR2 YZ 124" 154" 540" 8/6/2010 3-13 9HD0560.
SECTION 3 - SUPERHARROW 2650 862" 24" 48" 48" * 208 1/4" 370" 350" NOTE: DIMENSIONS SHOWN ARE APPROXIMATE. CABLE ATTACH BRACKETS SHOULD BE POSITIONED SO WING TUBES ARE LEADING BY 2°. *CONNECT REAR CABLES (8D1760) AT CENTER OF MACHINE WITH FOLLOWING HARDWARE: QTY. PN DESCRIPTION 1 8X0111 BOLT 3/4-10NC X 2-1/2" GR5 YZ 2 8X0318 WASHER 3/4" FLAT YZ 1 8X0261 NUT 3/4"-10NC NY-LOCK GR2 YZ 124" 154" 636" 8/6/2010 3-14 9HD0720.
SECTION 3 - SUPERHARROW 2650 1054" 24" 48" 48" * 208 1/4" 432" 366 3/4" NOTE: DIMENSIONS SHOWN ARE APPROXIMATE. CABLE ATTACH BRACKETS SHOULD BE POSITIONED SO WING TUBES ARE LEADING BY 2°. *CONNECT REAR CABLES (8D1760) AT CENTER OF MACHINE WITH FOLLOWING HARDWARE: QTY. PN DESCRIPTION 1 8X0111 BOLT 3/4-10NC X 2-1/2" GR5 YZ 2 8X0318 WASHER 3/4" FLAT YZ 1 8X0261 NUT 3/4"-10NC NY-LOCK GR2 YZ 124" 154" 732" 8/6/2010 3-15 9HD0880.
3-16 8Z0092 HITCH WARNING 8Z0276 GENERAL CAUTION 12/17/2013 8Z0204 5.5" SUMMERS DECAL 8Z0093 AUTO-FOLD LOCK WARNING 8Z0346 ELECTROCUTION DANGER 8Z0232 AUTO-FOLD WARNING 8Z0075 TRANSPORT LOCK DECAL DECALS 8C2200.
SECTION 3 - SUPERHARROW 2650 OPERATING INSTRUCTIONS TRANSPORT TO FIELD POSITION 1. Hitch machine to tractor drawbar using a locking pin and safety chain. Connect hydraulic hoses and wiring. Retract jacks and rotate into storage position 2. Select level area to lower machine into field position. 3. IMPORTANT: Remove transport locks. Store locks in storage guide shown in Figure 10. Fig. 10: Transport Lock in Locked Position 4. Back up machine slowly, maneuvering so wings open evenly.
SECTION ADJUSTMENT SECTION 3 - SUPERHARROW 2650 Section down pressure can be increased or decreased hydraulically by adjusting lift cylinders and manually by adjusting the lift cylinder adjustment bolt (8K1720, Page 3-2). Down pressure on wing sections can be increased by replacing the top spacer tubes (8HD0510) with extra pressure spacer tubes (8HD0520). Lower stop bushings can also be replaced with 8HD0520 to adjust individual sections so the machine raises more evenly.
SECTION 3 - SUPERHARROW 2650 FIELD TO TRANSPORT POSITION 1. Stop in a level area and back tractor up to provide slack in pull cables. 2. Open manual lock valve on auto-fold lock cylinder. Fully extend auto-fold lock cylinder. 3. Fully retract Hydraulic Depth Adjust cylinders. 4. Fully retract lift cylinders raising sections. 5. While machine is resting on its transport wheels, drive tractor forward. Wings should fold to transport position.
SECTION 3 - SUPERHARROW 2650 Spring Seedbed Preparation Suggested settings and adjustments for Spring Seedbed Preparation with the Summers Superharrow 2650. IMPORTANT: Sections are designed to run level insuring that all teeth work at the same depth. If rear of section is running higher than the front, the section is incorrectly adjusted and component failure may occur. Summers products are NOT warranted for damage caused by improper adjustment a. Extend hydraulic depth adjustment cylinders 1/2 way.
SECTION 3 - SUPERHARROW 2650 MAINTENANCE AND SERVICE Daily Maintenance: Check all wheel and frame bolts for tightness. Daily Greasing: Two zerks on each knuckle. One zerk on each transport axle pivot. Two zerks on each cable auto-fold arm. Two zerks on hitch hydraulic depth adjustment – pillow block casting (8R6065, page 3-3). Weekly Maintenance: Inspect wheel bearings for tightness. Seasonal Maintenance: Disassemble, clean and repack wheel bearings.
SECTION 3 - SUPERHARROW 2650 3-22
SECTION 4 - HARROW PACKER SET-UP INSTRUCTIONS Fig. 1: Field Position Fig. 2: Transport Position The machine should be placed in an area that allows ample room for field position assembly (See Fig. 1). 19" 19” Refer to illustrations and parts listings in this section. Position center of axles 19” ahead of the rear of the hitch 8” X 4” tube. Mount hitch wheels and tires and install hitch jack. If machine is equipped with optional Hydraulic Depth Adjustment, see pages 3-3 through 3-7 for (HDA) assembly.
4-2 8X0140 1 X 7" 8X0318 3/4" FW 8X0114 3/4 X 3" 8D0722 (OPT) 8D0720 8D2470 NOTE: CUSHIONS CAN BE ADDED TO DECREASE HOLE SIZE.
4-3 8X0261 3/4" LN DETAIL A SCALE 1 / 10 8X0318 3/4" FW 8C2650 8X0414 8D2730 8X0281 NY-LOCK 1" 8X0414 8D2730 8D2400 8C2680 (SINGLE CABLE) AUTO-FOLD A 8C2660 8C2610 8D2400 8D2730 8X0150 1" X 20" 8R6145 8X0260 3/4" N 8C2620 3/17/2014 8X0063 1/2 X 1-1/2" 8C1470 8C1940 9SS6075H.
SECTION 4 - HARROW PACKER SET BOLTS FOR AUTO FOLD ARM ADJUSTMENT 8X0259 3/4” JN 8X0112 3/4”X2-1/4” 22’ HITCH — 8” SQUARE DRAWBAR Specification Chart Machine Size Cable Length PN-Cable PN-Wing (Hngd Wing Left Part 1) PN-Hinged Wing - Right Part 1 PN-Hinged Wing - End PN-Lift Cylinder SH+ COIL PACKER (9/16” Tooth) 36’ 246” 48’ 521” 60’ 581” 8D1860 8D1970 8D1980 8HD6620 8HD6640 8HD6660 8C0432 8C0532 8C0532 HARROW PACKER (3/8” Tooth) 30’ 227” 40’ 262” 50’ 521” 60’ 581” 70’ 661” 8D1850 8D18
SECTION 4 - HARROW PACKER DRAWBAR ASSEMBLY 8X0286 1 1/2" JN 8X0268 7/8" N 8X0307 7/8" LW 8X0242 NY-LOCK 1/2" N 8X0211 5/16" FN 8K8200 8X0203 3/8" FN 8C2280 8S1126 8C1780 7/8 X 8-1/16 X 10" 8S1120 8D8522 M 8C1710 3/8 X 8 X 9" 8X0330 1/2" FW 8C1480 8X0068 1/2 X 2.
SECTION 4 - HARROW PACKER 8C1452 1 X 6 1/2” PIN 8X0414 CTR PIN 8C2246 8J6010 8J6010 3/4”-16ORB X #6JIC(M) 90° ADP 3/4”-16ORB X #6JIC(M) 90° ADP 1 X 5 7/8” PIN 5/16” CTR PIN 8X0414 CTR PIN 8C1420 8X0418 8C1452 1 x 6 1/2” PIN 8N3048 3/8 X 48” HH 8J6010 8N3124 3/4”-16ORB X #6JIC(M) 90° ADP 3/8 X 124” HH 8C2246 8X0418 RESTRICTOR VALVE 8J7116 ASSEMBLY 3/4”-16ORB X 3/4”-16ORB 1-WAY 1/16” RESTR 8J5510 3/4”-16ORB X #6JIC(M) STR CTR PIN 8N3096 3/8 X 96” HH 8N3018 8C0432 8C0532 - 3/8 X 18”
4-7 8D2100 6 LINK 8X0125 3/4" X 10" 8X0306 3/4" LW 8D2300 9 LINK 8X0330 1/2" FW 8X0242 NY-LOCK 1/2" N 8X0260 3/4" N 8D2210 8 LINK 8X0065 CRG 1/2 X 2" (OPT.
4-8 8X0303 1/2" LW 8X0073 1/2 X 5" 8W1204 1/2 X 3 X 3" 8X0242 NY-LOCK 1/2" N 8X0240 1/2" N * SUPERHARROW PLUS WITH COIL PACKER ONLY 8C4010 8X0063 1/2 X 1-1/2" 8HD6160 - SHORT* (3") 8HD6170 - LONG* (13") 8C4020 - SHORT (12") 8C4040 - LONG (47 3/4") 8HD6174 - SHORT* (23 3/4") 8HD6176 - LONG* (59 3/4") PACKER ASSEMBLY 8X0303 8C4000 8X0301 8C1420 8X0316 1" FW 8X0418 8C4082 7C4020 Packer Assembly.
4-9 8H1110 8H1110S (OPT) 8X0242 NY-LOCK 1/2" N 8H0643 8H0641 8X0071 1/2" X 3" 8H0232 8H0642 8X0400 HPC 8X0234 7/16" LNUT OPT. SPRING PRESSURE MOUNTING HOLE 8H0390 8X0234 7/16" LNUT 8H0644 CHAIN MNT HOLE 8H0645 8H0411 8X0420 CLVS PIN 8X0034 7/16" X 1-3/4" 8H0645 5 FT. HARROW SECTION - 5 BAR (3/8" Dia. Tooth - 8H0795) 7/21/2010 8S0080 1.
SECTION 4 - HARROW PACKER Sections with 9/16” diameter teeth: See assembly instructions on page 2-10 for installation of sections. Attach two long lift arm extensions to the lift arms on the first section to left of center. Extensions for adjoining sections must be alternating lengths (short and long). See Figures 3 & 4 (Page 4-12) for alteration instructions of two tines above knuckles. NOTE: Do not use 8HD6150 (Angle, tooth stop – shown on page 2-11).
SECTION 4 - HARROW PACKER PIVOT STOP AUTO-CABLE FOLD Mount auto-fold pivot brackets ahead of welded stop. Do not fully tighten u-bolts. Attach left and right cable fold arms to pivot brackets with 1-1/4” X 14” pins and hardware. Adjust pivot brackets to provide clearance between cable fold arm bottom guide and hitch tube. This adjustment is made with 3/4” X 2-1/4” bolts (8X0112, page 4-4). This adjustment will allow cable fold arms to pivot freely into transport position.
SECTION 4 - HARROW PACKER 4-12
SECTION 4 - HARROW PACKER 4-13
SECTION 4 - HARROW PACKER OPERATING INSTRUCTIONS TRANSPORT TO FIELD POSITION 1. Hitch machine to tractor drawbar using a locking hitch pin and safety chain. Connect hydraulic hoses and wiring. Retract jacks and rotate into storage position. 2. Select level area to lower machine into field position. 3. IMPORTANT: Remove transport locks. Store locks in storage guide shown in Figure 5. Fig. 5: Transport Lock in Locked Position 4. Back up machine slowly, maneuvering so wings open evenly.
SECTION 4 - HARROW PACKER CABLE PULL BRACKETS Under severe conditions (heavy machine draft due to deep penetration or high field speed) cable brackets may slide on drawbar wing tube, resulting in improper cable adjustment. The recommended solution for this is to relocate cable pull brackets at desired position and weld a stop on drawbar next to cable pull brackets. FIELD TO TRANSPORT POSITION 1. Stop in a level area and back tractor up to provide slack in pull cables. 2.
SECTION 4 - HARROW PACKER MAINTENANCE & SERVICE Daily Maintenance: Check all wheel bolts for tightness. Daily Greasing: Two zerks on each knuckle. Two zerks on each cable auto-fold arm. One zerk on each transport axle pivot. Weekly Greasing: One zerk on each packer bearing (one stroke only). Weekly Maintenance: Inspect all wheel bearings for tightness. Seasonal Maintenance: Disassemble, clean and repack wheel bearings. Lubricate all zerks with a good grade of general purpose grease.
SECTION 5 - 4-RANK SUPERWEEDER Fig. 1: Field Position Fig. 2: Transport Position The machine should be placed in an area that allows ample room for field position assembly (See Fig. 1). CAUTION: For safety purposes, block equipment while working on it. Refer to illustrations and parts listings on pages 5-2 through 5-20 and follow these steps when assembling. HITCH – Axles, Wheels and Jack Attach hitch axle assemblies as shown on page 5-2.
5-2 8X0140 1 X 7" 8X0318 3/4" FW 8X0114 3/4 X 3" 8D0722 (OPT) 8D0720 8D2470 NOTE: CUSHIONS CAN BE ADDED TO DECREASE HOLE SIZE.
8X0260 3/4" N 8W1862 8X0306 3/4" LW 8W1860 5-3 8W1886 8X0121 3/4" X 6-1/2" 8X0092 5/8" X 2-3/4" 8R6065 W/ZERK 8R6060 8W1850 8T3300 8R6067 8X0327 1 1/4" FW 8C2325 8X0261 3/4" LN 8W1884 L 2.5 x 2.5 x 3/8 8X0115 3/4 X 3-1/2" 8R6810 SS BUSH 8X0304 5/8" LW 8X0250 5/8" N 8X0260 3/4" N 1/13/2014 8X0115 3/4 X 3-1/2" 8W1890 8X0265 3/4" LN DETAIL A SCALE 0.08 : 1 8X0070 1/2 X 3-1/4" 8K1100 8X0281 NY-LOCK 1" 8X0316 1" FW 9HD0880.
5-4 8D2400 8D2730 8X0318 3/4" FW 8C2650 8D2730 8C2690 8D0312 8X0414 8C1920 (DUAL CABLE ONLY) 8X0281 NY-LOCK 1" 8X0261 3/4" LN 8C1900 8X0414 8C2690 8D0312 AUTO-FOLD SI IN 8S1076 4" <2 > DE SI N I m TO imu K x a O HO 47" m E D 8X0150 1" X 20" 8X0261 3/4" LN 1/2/2014 8X0330 1/2" FW 8R6145 8C1940 8X0063 1/2 X 1-1/2" SEE CABLE CHART FOR CABLE LENGTH AND PART NUMBER 8C2600 8C1760 3/4 X 8-1/16 X 6" 8C1470 9HD0880.
SECTION 5 - 4-RANK SUPERWEEDER DRAWBAR ASSEMBLY 8X0211 5/16" FN 8C1780 7/8 X 8-1/16 X 10" 8X0330 1/2" FW 8X0021A 5/16 X 1" 8X0068 1/2 X 2.
SECTION 5 - 4-RANK SUPERWEEDER 406" 376" 346" 316" 286" 257" 224" 196" 136" 166" 106" 76" 45" 15" 0" C D Centerline Of Machine 7 1/2" 30" 31" 7 1/2" 15" 30" 31" 30" 20" Centerline Of Machine TYPICAL EXTENDED S-TINE LOCATIONS 2 1/2" DETAIL D SCALE 1 : 30 2 1/2" 1/14/2014 5-6 9W7022.
5-7 8X0269 7/8" JAM NUT 8X0132 7/8" X 2-1/2" 8D1750 8X0067 1/2-13NCX2-1/4" 8X0303 1/2" LW 8X0605 7/16 X 1" SET SCREW 8X0240 1/2" N 8X0232 7/16" N 8D1740 8X0415 8X0330 1/2" FW 8X0415 8D1702 8C1780 7/8 X 8-1/16 X 10" 8X0303 1/2" LW 8X0242 NY-LOCK 1/2" N 8X0330 1/2" FW 8D1720 8X0330 1/2" FW 8H1320 8D1730 8D1710 8X0400 HPC 8X0242 NY-LOCK 1/2" N 8D2100 6 LINK 8W1710 8W1720 - W/CYL. ATTCH.
SECTION 5 - 4-RANK SUPERWEEDER TINE TUBES AND TINES Special Lift Arm for Hydraulic Cylinder Connecting Lever 1/2” x 2-1/4” Cap Screw Connecting Link 1/2” Lock Nut Cylinder Lever Tube Bushing Tine Mounting Tube 1/2” U-Bolt Tube Clamp Assembly Fig. 3: Lift arms and tine tube assembly – 4-Rank Assemble tine tube and S-tines to lift arms as shown in Figure 3. Secure tube bushings in place with four 7/16” X 1” bolts, lock washers and nuts.
5-9 8W1020 - 2.75" OPT. 8W1021 - 4" STD. 8X0302 7/16" LW 8X0302 7/16" LW 8W1015 STANDARD (SLVR) 8W1016 HI-CLR (GOLD) 8W1710 8W1228 - 102-1/2" 8W1230H - 110" 8W1245H - 162-1/2" 8W1250 - 172" 4/15/2014 4 RANK SUPERWEEDER SECTION 8W1275 8X0240 1/2" N 8W1280 8X0250 5/8" N 8W1264 8X0067 1/2-13NCX2-1/4" 8W1710 8X0304 5/8" LW 8W1285 8X0096 5/8" X 4" 8W1720 W/CYL. ATTCH 8W1200 1/2 X 2 X 3-1/4" 8X0303 1/2" LW 8D9116 W/CYL.
SECTION 5 - 4-RANK SUPERWEEDER Spacing measurements shown begin at centerline and apply to all machines. 30 Ft. Spacing Legend a = 2-1/2” b = 7-1/2” c = 15” d = 30” Centerline Of Machine e = 20” = 1/4” Thick Wall Tube (Painted Black) 30” 31” d c 31” 30” e * b b * a a – Typical Extended S-tine Locations. 40 Ft. 8W1245H 162 1/2” 8W1245H 162 1/2” 50 Ft. Left Wing *Space S-tines between these lift arms only at 21” Right Wing Fig.
SECTION 5 - 4-RANK SUPERWEEDER 60 Ft. 8W1245H 162 1/2” (8W1228) 102-1/2” 8W1245H 162 1/2” 70 Ft. Left Wing (8W1228) 102-1/2” Right Wing (8W1245H) 162-1/2” Left Wing Right Wing Fig.
SECTION 5 - 4-RANK SUPERWEEDER HYDRAULIC S-TINE DEPTH CONTROL Mount 2-1/2” X 8” cylinders on lift arms as shown in Figure 3. Connect hose lines to cylinders and manifold block mounted on hitch (See Figures 6 & 7). Assemble tractor hose lines and route with lift cylinder lines along hitch. Secure 1/4” hydraulic hose to lift arms with clamps (8W1390) and u-bolts provided. Leave slack in lines at knuckles between center and wing sections.
Hose Lengths a = 24” - 8N2024 b = 110” - 8N2110 c = 120” - 8N2120 d = 190” - 8N2190 e = 135” - 8N2135 f = 250” - 8N2250 g = 76” - 8N2076 h = 50” - 8N2050 i = 210” - 8N2210 (50’) (40’) (40’) (50’) 8W1357 Fig. 7: Hydraulic System, S-Tine Rotation – 4-Rank Superweeder 5-13 8N3312 3/8X312” 8W1360 8N3288 3/8X288” 8J6010 8J5500 8J6010 8D9116 60 and 70 Ft. Units 10/15/13 Manuals/22ft. Hitch/Photos/HydSysRot2 8J5300 8J5300 (50’) (40’) (40’) (50’) 40 and 50 Ft.
5-14 8J5510 3/4”-16ORB X #6JIC(M) STR 8N3252 NYL.
SECTION 5 - 4-RANK SUPERWEEDER 8N3288 - 3/8X288” HH (30’) 8N3360 - 3/8X360” HH (40’) 8N3432 - 3/8X432” HH (50’) 5-15
5-16 8H1110 8H1110S (OPT) 8X0242 NY-LOCK 1/2" N 8H0643 8H0641 8X0071 1/2" X 3" 8H0232 8H0642 8X0400 HPC 8X0234 7/16" LNUT OPT. SPRING PRESSURE MOUNTING HOLE 8H0390 8X0234 7/16" LNUT 8H0644 CHAIN MNT HOLE 8H0645 8H0411 8X0420 CLVS PIN 8X0034 7/16" X 1-3/4" 8H0645 5 FT. HARROW SECTION - 5 BAR (3/8" Dia. Tooth - 8H0795) 7/21/2010 8S0080 1.
SECTION 5 - 4-RANK SUPERWEEDER TRANSPORT WHEELS Locate transport wheel assemblies as shown in chart below. TRANSPORT WHEEL ASSEMBLIES Machine Size Location on Wing Pivot Tube Position 30’ & 40’ Over End Section Up Between end and 50’ & 60’ Second Section from Up End of Wing Over Second 70’ Section from End of Down Wing Secure with 7/8” u-bolts and hardware. Transport axle “toe-in” can be adjusted with outside stop set bolt (8X0665, page 5-5).
SECTION 5 - 4-RANK SUPERWEEDER SET BOLTS FOR AUTO FOLD ARM ADJUSTMENT 8X0259 3/4” JN 8X0112 3/4”X2-1/4” 22’ HITCH — 8” SQUARE DRAWBAR Specification Chart Machine Size Cable Length PN-Cable 4-RANK SUPERWEEDER 30’ 40’ 50’ Inside Outside 60’ Inside Outside 70’ Inside Outside 227” 262” 246” 281” 262” 324” 262” 341” 8D1850 8D1870 8D1860 8D1880 8D1870 8D1900 8D1870 8D1910 PN-Wing (Hngd Wing Left Part 1) PN-Hinged Wing - Right Part 1 PN-Hinged Wing - End 8C3100 8C3150 8C3200 PN-Lift Cylinder 8
SECTION 5 - 4-RANK SUPERWEEDER 5-19
5-20 8Z0092 HITCH WARNING 8Z0276 GENERAL CAUTION 12/17/2013 8Z0204 5.5" SUMMERS DECAL 8Z0093 AUTO-FOLD LOCK WARNING 8Z0346 ELECTROCUTION DANGER 8Z0232 AUTO-FOLD WARNING 8Z0075 TRANSPORT LOCK DECAL DECALS 8C2200.
SECTION 5 - 4-RANK SUPERWEEDER OPERATING INSTRUCTIONS TRANSPORT TO FIELD POSITION 1. Hitch machine to tractor drawbar using a locking hitch pin and safety chain. Connect hydraulic hoses and wiring. Retract jacks and rotate into storage position. 2. Select a level area to lower machine into field position. 3. IMPORTANT: Remove transport locks. Store locks in storage guide shown in Figure 8. Fig. 8: Transport Lock in Locked Position 4. Back up machine slowly, maneuvering so wings open evenly.
SECTION 5 - 4-RANK SUPERWEEDER 5. Extend main lift cylinders to lower machine into field position. If pull cables become tight before transport wheel is off the ground, back up to provide slack in cable. 6. Hinged wing machines only: Remove 1-1/4” hinge lock pins and store in holes provided. LIFT ARM ADJUSTMENT To level individual lift arms in field position, loosen top nut of lift arm attach u-bolt and adjustment bolt jam nut. Turn adjustment bolt until lift arm is correctly positioned. Retighten nuts.
SECTION 5 - 4-RANK SUPERWEEDER UNHITCHING MACHINE 1. Park machine on a level area. Block wheels to prevent machine from rolling. 2. Follow steps outlined in WARNING – NEGATIVE HITCH WEIGHT on page 1-2. Fig. 9: Hitch Warning This hitch WARNING Decal (PN 8Z0092) must be installed at location indicated by arrow (Fig. 10). Fig. 10: Hitch Warning Decal Location If decal is missing from machine, contact your Summers Dealer for replacement.
SECTION 5 - 4-RANK SUPERWEEDER MAINTENANCE & SERVICE Daily Maintenance: Check all wheel bolts for tightness. Daily Greasing: Two zerks on each knuckle. Two zerks on each cable fold arm. One zerk on each transport axle pivot. 60 & 70 Ft. machines only: One zerk on each Hinged Wing Pivot. Weekly Maintenance: Inspect wheel bearings for tightness. Seasonal Maintenance: Disassemble, clean and repack wheel bearings. Lubricate all zerks with a good grade of general purpose grease.
6-1 22’ HITCH IMP.
6-2 4 1/2 x 16 5 X 16 8D9466 (CP-#2WNG) 8D9516 8D9518 ( -93) 8D9525(94- ) * (2" ROD) 8D9418 ( -93) 8D9418A (94- ) * 1-3/4" ROD) 8D9468 (98- ) 4 X 36 5 X 36 3 X 31 3 1/2 X 10 3 3/4 X 10 4 X 10 4 X 10 4 1/2 X 10 5 X 10 5 1/2 X 10 6 X 10 8K9640 8K9650 8R6870 (700 RP) 8T1035 (2" ROD) 8T1037 (1-3/8"ROD) 8T1040 (2" ROD) 8T1040B (1-3/8"RD) 8T1045 (2" ROD) 8T1050 (2-1/8"ROD) 8T1055 (2-1/4" ROD) 8T1060 (2-3/8" ROD) 4 1/2 X 8 4 3/4 X 8 (1.5"ROD) 5 X 8 (1.
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8A1155 8A1156 8A1157 8A4048 8A4050 8A4052 8A4054 8C0150 8C0216 8C0220 8C0250 8C0270 8C0432 8C0532 8C0535 8C0650 8C1420 8C1452 8C1470 8C1480 8C1700 8C1710 8C1718 8C1720 8C1736 8C1740 8C1751 8C1752 8C1755 8C1760 8C1780 8C1800 8C1800D 8C1802 8C1802D 8C1805 8C1805P 8C1900 8C1920 8C1940 8C1950 8C1970 8C2002 8C2200 8C2210 8C2246 8C2260 8C2270 8C2280 8C2300 8C2300H 8C2310 8C2310H 8C2316 8C2318 8C2320 8C2322H 8C2325 8C2350 8C2360 8C2420 8C243
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8C4615 8C4710 8C4715 8C5050 8C5840 8C5850 8C5860 8C5870 8C6010 8C6015 8C9010 8C9017 8C9030 8C9035 8C9040 8C9050 8C9055 8C9060 8D0312 8D0330 8D0340 8D0350 8D0720 8D0722 8D0724 8D0730 8D0745B 8D1160 8D1236 8D1242 8D1660 8D1700 8D1702 8D1710 8D1720 8D1730 8D1740 8D1750 8D1751 8D1760 8D1800 8D1810 8D1820 8D1830 8D1840 8D1850 8D1860 8D1870 8D1880 8D1890 8D1900 8D1910 8D1920 8D1930 8D1940 8D1950 8D1960 8D1970 8D1980 8D1990 8D2000 8D2100 8D2
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8D5316 8D5317 8D5319 8D5320 8D5332 8D5334 8D5336 8D5340 8D5355 8D8490 8D8500 8D8521 8D8521L 8D8521U 8D8522 8D8523 8D9108 8D9110 8D9113 8D9116 8D9118 8D9119 8D9119A 8D9130 8D9180 8D9192 8G2281 8G2282 8G2283 8G2284 8G2285 8G2286 8G8010 8G8020 8H0232 8H0260 8H0350 8H0370 8H0390 8H0410 8H0411 8H0641 8H0642 8H0643 8H0644 8H0645 8H0650 8H1110 8H1110S 8H1140 8H1140S 8H1180S 8H1184S 8H1190S 8H1195S 8H1280 8H1304 8H1307 8H1309 8H1311 8H1315 8H
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8H2096 8H2098 8H2099 8H2100 8H2107 8H2108 8H2114 8H2118 8H2120 8H2131A 8H2132 8H2142 8H2144 8H2150 8H2160 8H2170 8H2184 8H2190 8H2315 8H2601 8H2610 8H2618 8H2620 8H2634 8H2636 8H2660 8H2664 8H2666 8H2702 8H2706 8H2708 8H2710 8HD0064 8HD0080 8HD0150 8HD0152 8HD0160 8HD0200 8HD0510 8HD0520 8HD0522 8HD0532 8HD0540 8HD0550 8HD0591 8HD0591L 8HD0592 8HD0592L 8HD0593 8HD0593L 8HD0594A 8HD0594L 8HD0595A 8HD0595L 8HD5052 8HD5054 8HD5056 8HD505
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8HD6660 8HD6663 8HD6664 8HD6665 8HD6680 8HD6682 8HD6684 8HD6685 8HD6698 8HD7000 8HD7020 8HD7040 8HD7060 8HD7080 8HD7100 8HD7110 8HD7120 8HD7130 8HD7136 8HD7148 8HD7160 8HD7172 8HD7184 8HD8200 8J5100 8J5102 8J5110 8J5152 8J5200 8J5298 8J5300 8J5312 8J5500 8J5510 8J5520 8J5540 8J5600 8J5620 8J5680 8J5682 8J5690 8J5700 8J5710 8J6000 8J6002 8J6004 8J6010 8J6020 8J6030 8J6060 8J7000 8J7040 8J7116 8J7216 8J7250 8J7260 8K0050 8K1720 8K1750 8
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8K8015 8K8020 8K8030A 8K8060B 8K8067 8K8070B 8K8074 8K8075A 8K8080A 8K8088 8K8090B 8K8095B 8K8105A 8K8200 8K8210 8K8220 8K8430 8K8435 8K8440C 8K8445C 8K8452C 8K8455 8K8460 8K8520 8K8530 8K8540 8K8600 8K8610 8K8620 8K8630 8K8642 8K8644 8K8646 8K8660 8K9102 8K9106 8K9108 8K9174 8K9176 8K9178 8K9180 8K9200 8L0251 8L0252 8L0258 8L0260 8L0262 8L0266 8L0268 8L0270 8L0272 8L1060 8N2012 8N2024 8N2036 8N2050 8N2054 8N2060 8N2072 8N2076 8N2088
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8N3390 8N3408 8N3432 8N3462 8N3534 8N3570 8N3606 8N4016 8N4060 8N4114 8N4120 8N4138 8N4160 8N4198 8N4216 8N4228 8N4546 8N4624 8N7000 8R6060 8R6065 8R6067 8R6805 8R6808 8R6810 8R6815 8R6820 8R6901 8R6902 8R6911 8R6913 8R6914 8R6915 8R6917 8R6921 8R6922 8R6923 8R6924 8R6925 8R6927 8S0080 8S0330 8S0340 8S0345 8S0358 8S0360 8S1076 8S1120 8S1124 8S1126 8S2980 8S2990 8T2986 8T2988 8T2990 8W1006 8W1007 8W1011 8W1012 8W1015 8W1016 8W1020 8W10
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8X0000B 8X0001 8X0002 8X0004 8X0005 8X0006 8X0007 8X0008 8X0009 8X0010 8X0013 8X0014 8X0015 8X0016 8X0017 8X0019 8X0020 8X0021 8X0021A 8X0021B 8X0022 8X0023 8X0030 8X0031 8X0033 8X0034 8X0036 8X0038 8X0041 8X0044 8X0045 8X0046 8X0047 8X0048 8X0061 8X0062 8X0063 8X0064 8X0065 8X0065L 8X0065S 8X0066 8X0067 8X0068 8X0069 8X0070 8X0071 8X0072 8X0073 8X0074 8X0075 8X0077 8X0078 8X0080 8X0082 8X0083 8X0084 8X0087 8X0090 8X0091 8X0092 8X0093
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8X0142 8X0143 8X0145 8X0146 8X0149 8X0150 8X0201 8X0202 8X0203 8X0205 8X0210 8X0211 8X0212 8X0218 8X0220 8X0222 8X0223 8X0232 8X0234 8X0240 8X0242 8X0244 8X0246 8X0250 8X0251 8X0253 8X0256 8X0259 8X0260 8X0261 8X0264 8X0265 8X0266 8X0268 8X0269 8X0270 8X0274 8X0277 8X0278 8X0280 8X0281 8X0282 8X0283 8X0284 8X0285 8X0286 8X0290 8X0292 8X0292S 8X0299 8X0300 8X0301 8X0302 8X0303 8X0304 8X0306 8X0307 8X0308 8X0309 8X0311 8X0315 8X0316 8X0
SECTION 7 - PART NUMBERS Stock Code Description Stock Code Description 8X0480 8X0492 8X0505 8X0520 8X0523 8X0528 8X0605 8X0632 8X0665 8X0708 8X0710 8X0721 8X0725 8X0727 8X0728 8X1120 8Z0070 8Z0075 8Z0079 8Z0087 8Z0089 8Z0090 8Z0092 8Z0093 8Z0126 8Z0127 8Z0232 8Z0276 8Z0340 8Z0342 8Z0344 8Z0346 8Z0650 8Z0800 8Z0805 8Z0810 8Z1000 8Z1101 8Z1101R HITCH PIN W/LYNCH 5/8X4”YZ LYNCH PIN 3/16 X 1-1/4” YZ S-HOOK .
History of Summers Manufacturing Co., Inc. 1965 – Summers Manufacturing is founded by Harley Summers, who purchases patent rights for Goebel truck and pickup hoists from the Goebel Brothers of Lehr, ND. These hoists, produced in Harley Summers’ blacksmith shop the first year, were distributed nationwide by a Cincinnati, Ohio, dealer. With increasing sales, the company soon outgrows the small shop. Summers wins the Herman harrow contract, beginning the company’s Herman culti-harrow line.
Tillage Cultivators/Harrows Rock Picker Mounted Attachments Land Rollers/Packers Sprayers 1-800-732-4347 • www.summersmfg.
