62’ & 84’ SUPERROLLER Operator’s Manual 62’ & 84’ SUPERROLLER 62’ & 84’ SUPERROLLER IMPORTANT THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE SINCE MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. See www.summersmfg.com for latest version of all Summers Operator’s Manuals. SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.com MADDOCK, NORTH DAKOTA 58348....................................
Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 12 months from the date of purchase by the end user from Summers’ dealer.
INTRODUCTION This manual provides the following information about your Summers Land Roller. SECTION CONTENTS Section 1 – SAFETY explains important safety precautions and familiarizes the Operator with the decals and their locations. Section 2 – ASSEMBLY includes step by step assembly instructions for your Summers Land Roller. Section 3 – LAND ROLLER OPERATION provides necessary information for the operation and adjustment of the machine.
TABLE OF CONTENTS SECTION 1 – SAFETY Safety-Alert Symbol......................................................................................................................................1-1 General Safety Practices................................................................................................................................1-1 Safety During Transport.................................................................................................................................
SECTION 1 - SAFETY SAFETY-ALERT SYMBOL This symbol is used to denote possible danger and care should be taken to prevent bodily injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to limited to the most extreme situations.
SECTION 1 - SAFETY SAFETY DURING TRANSPORT 1. Ability to safely operate the Summers Superroller is determined by both tractor horsepower and weight. The minimum tractor weight for operating this implement is 30,000 lbs. Minimum tractor engine horsepower is 300. Dual tires or single tires set at maximum width are required for safe operation of Land Roller. 2. ONLY TOW at a safe speed – 20 MPH MAXIMUM. Use caution when making corners and meeting traffic. 3.
SECTION 1 - SAFETY 3. PN 8Z0087 – DECAL FOR PINCH POINT HAZARD 4. PN 8Z0132 – SUPERROLLER ID DECAL 5.
SECTION 1 - SAFETY 6. PN 8Z0800 – AMBER REFLECTOR 7. PN 8Z0805 – RED-ORANGE REFLECTOR 8. PN 8Z0810 – RED REFLECTOR SAFETY LIGHT OPERATION The Summers Safety Light Kit is equipped with a 7 pin connector which meets SAE J560 specification. To protect 7 pin connector, store in dust cap (8K8067) when not attached to towing vehicle. On most towing vehicles WITHOUT brake lights: Amber lights will turn on with flashers or turn signals. Red lights will turn on with parking, road or field lights.
8Z0805 8Z0087 8Z0810 8Z0087 DETAIL A 8Z0800 1-5 8Z0800 8Z0800 8Z0087 8Z0800 8Z0800 8Z0087 8Z0075 ON ALL TRANSPORT CYCLINDERS 8Z0800 8Z0132 8Z0079 NOTE: DECALS ARE SYMMETRICAL WITH EXCEPTIONS OF 8Z0087, 8Z0276 AND 8Z0075. 8Z0276 12/9/2009 9LR6242.
SECTION 1 - SAFETY 1-6
SECTION 2 - ASSEMBLY GENERAL ASSEMBLY SAFETY PRACTICES 1. READ AND UNDERSTAND Operator’s Manual before assembly of machine. 2. If machine is to be assembled INDOORS, check that exit door is a MINIMUM OF 18’ WIDE and a MINIMUM of tractor height. 3. Reference to “RIGHT” and “LEFT” is determined when machine IS VIEWED FROM THE REAR. 4. Reference to “FORWARD” means TOWARDS THE TRACTOR. 5. Reference to “REAR” means AWAY FROM THE TRACTOR.
SECTION 2 - ASSEMBLY GENERAL SAFETY PRACTICES BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking. YOU ARE RESPONSIBLE for the safe assembly of the machine. ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear. DO NOT ALLOW CHILDREN or other unauthorized persons within the assembly area. BE SURE LIFTING DEVICE IS RATED TO HANDLE THE WEIGHT.
SECTION 2 - ASSEMBLY Main Frame Roller Installation (Instructions for both 62’ & 84’) (NOTE: 62’ shown in drawings) MF1. Position 8P4215 on a flat even surface; block the roller to avoid unexpected movement. CAUTION: The 15’ roller weighs 4285 lbs., use extreme care when moving rollers and frame components. NOTE: An H has been stamped onto one end of each roller. Position the center roller with the H to the left. All other rollers should have the H positioned to the center of the machine. MF2.
SECTION 2 - ASSEMBLY Hitch Installation H1. Position hitch as shown in Figure 2; install the pins and hardware shown in Figure 2. IMPORTANT Always install the pins with the cross hole towards the outside. Pay attention to the orientation of the cross hole in the pin to the cross hole in the bushing on the main frame, only drive the pin in far enough to line up the holes, install the fasteners shown in Figure 2. H2. Install the jack stand and pin. H3.
8X0095 5/8" X 5" 8D9108 1/4 X 2" RP Figure 2 8X0323 5/8" FW 8X0327 1 1/4" FW DETAIL B 8X0253 NY-LOCK 5/8"-11NC 8P3910 8D9108 1/4 X 2" RP B 8X0327 1 1/4" FW 8D9108 1/4 X 2" RP 8X0304 5/8" LW 8K1620 8P7140 2-5 8P7130 A 8X0327 1 1/4" FW 8D8500 8X0523 ROLL PIN 8X0110 3/4 X 1.25" 8D8490 8K8067 8X0318 3/4" FW 8X0309 1" LW 8X0281 NY-LOCK 1" 8D8522 8D0720 NOTE: DRUM OMITTED FROM THIS VIEW. DETAIL A 8X0140 1 X 7" 3/25/2009 9LR6242.
SECTION 2 - ASSEMBLY Main Frame Transport Frame Installation T1. Loosely position 8T4100 on the main frame and affix the hardware associated with 8T4100. Do not tighten the fasteners. 8T4100 should always be positioned as shown, with the offset gap to the inside. 8T4100 OFFSET GAP TO INSIDE 3/28/2008 9LR6242.iam/8T4100 OFFSET T2. Position the transport frame at the rear of the main frame, note the orientation of the cylinders clevis.
8T4100 8X0044 7/16" X 3-1/2" 2-7 8K7042 8X0306 3/4" LW 8X0234 7/16" LNUT 8T3640 8D9108 1/4 X 2" RP 8X0265 3/4" LN A 8X0242 NY-LOCK 1/2" N 8X0327 1 1/4" FW 8D9108 1/4 X 2" RP 8X0327 1 1/4" FW 8K9106 8P0510 8K1105S DETAIL A 8D9108 1/4 X 2" RP 8D9108 1/4 X 2" RP 8X0072 1/2" X 3-3/4" 8P7180 8X0327 1 1/4" FW 8X0327 1 1/4" FW 3/25/2009 8K9106 9LR6242.
SECTION 2 - ASSEMBLY Part 1 Wing Installation The following instructions depict the left part 1 wing being installed on the machine. The right hand wing will follow the same procedure. P1W 1. Install the cast knuckle, 8C1805. The orientation of the knuckle is extremely important. Installing the knuckle in the wrong orientation will not allow the wings to fold properly. Structural damage may occur if the knuckle is installed incorrectly and the machine is unfolded. Install the pins and hardware as shown.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY Figure 4 8P7100L - 84' LEFT 8P7100R - 84' RIGHT 8P7102L - 62' LEFT (SHOWN) 8P7102R - 62' RIGHT 8X0095 5/8" X 5" 8X0253 NY-LOCK 5/8"-11NC 8K1660 8X0304 5/8" LW 8X0323 5/8" FW 8D9108 1/4 X 2" RP 8X0304 5/8" LW 8X0323 5/8" FW 8X0095 5/8" X 5" 8K9106 DETAIL B 8X0253 NY-LOCK 5/8"-11NC 8X0327 1 1/4" FW 8X0234 7/16" LNUT 8T3640 8T4100 8C1805 8X0327 1 1/4" FW B 8P6100 8P6100 8X0306 3/4" LW 8R6040 A C 8X0265 3/4" LN 8X0044 7/16" X 3-1/2" 8K7042 8P4215
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY Figure 5 A 8X0327 1 1/4" FW 8X0095 5/8" X 5" 8D9108 1/4 X 2" RP 8X0323 5/8" FW 8D9108 1/4 X 2" RP 8X0304 5/8" LW 8P3910 8K9106 8X0253 NY-LOCK 5/8"-11NC 8P7150LB 8P0510 8X0327 1 1/4" FW 8X0323 5/8" FW DETAIL A 8X0323 5/8" FW 8X0304 5/8" LW 8X0095 5/8" X 5" 8P3910 8X0304 5/8" LW 8X0095 5/8" X 5" 8X0253 NY-LOCK 5/8"-11NC 8P3910 8P7112L - 62' LEFT (SHOWN) 8P7112R - 62' RIGHT 8P7110L - 84' LEFT 8P7110R - 84' RIGHT 8P4212 - 62' 8P4217 - 84' 8P4205 -
SECTION 2 - ASSEMBLY 1. Install snap rings on each roller shaft. Ensure that the roller is centered in the bearings and tighten the set screws. P1W6. Install the hubs on 8P6100 as shown in Detail C of Figure 4. Attach with the shown hardware and tighten. P1W7. Install the tires to the hubs installed in the previous step. Tighten the wheel nuts to 170 ftlbs. torque. P1W8. Loosely position 8T4100 on the wing frame and affix the hardware associated with 8T4100. Do not tighten the fasteners. P1W9.
SECTION 2 - ASSEMBLY Caster Installation Note: The caster wheel shown in Figure 6 is for the left hand side. The tire should be positioned towards the drum. C1. Install 8P7190B as shown in the diagram, center 8P7190B on the caster wing. Attach with the hardware shown, tighten all nuts. C2. Install 7P8530 into the caster weldment, attach the spindle with the hardware shown and tighten all fasteners. C3.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY Figure 6 A 8X0286 1 1/2" JN 8X0368 1-1/2" FW 8X0114 3/4 x 3" 8X0306 3/4" LW 8P7200 8P7250 8K9102 8X0260 3/4" N 8X0261 3/4" LN 8X0292 2" SLTD N 8X0320 3/8" FW 8D9108 1/4 X 2" RP 8X0202 3/8" LN 7P8530 8P7190B 8K1723 8D9108 1/4 X 2" RP 8P7160L 8K5200 7L2150 8L0320 8P0302 8X0306 3/4" LW 8X0122 8X0260 3/4" N 8K7042 8X0072 1/2" X 3-3/4" 2-13 8L0252 8K1105S 8X0284 1 1/4" N 8X0242 NY-LOCK 1/2" N 8X0311 1 1/4" LW 12/9/2009 9LR6242.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8P7050 - 62' 8P7050 - 84' (42" DIA.) 8P7040 - 84' (36" DIA.) NOTE ORIENTATION OF CLIPPED CORNERS DETAIL B SCALE 1/10 8P7030 - 62' 8P7030 - 84' (42" DIA.) 8P7020 - 84' (36" DIA.) B 8P7070 - 62' 8P7010 - 84' (42" DIA.) 8P7000 - 84' (36" DIA.) 8X0064 CRG 1/2 X 1-1/2" 8P7070 - 62' 8P7010 - 84' (42" DIA.) 8P7000 - 84' (36" DIA.) A DETAIL A SCALE 1/10 8X0246 1/2" FN NOTE: DRUMS OMITTED 8/2/2010 2-14 9LR6242.
SECTION 2 - ASSEMBLY Hydraulic Installation H1. Install Hydraulic components as shown in Figure 7 provided. A. Leave enough slack at all pivot points to allow folding machine without stretching or pinching hydraulic hoses. B. Secure hoses with nylon ties and clamps provided. Do not over tighten clamps. H2. Install 8J5300 (one to each port) on front cylinder. Install 8J5700 to each end of tees.
SECTION 2 - ASSEMBLY NOTES 2-16
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY Figure 7 TO REAR CASTER LOCK CYLINDERS (H HOSES) E 8J6010 (4X) FROM TRACTOR (432" HOSES) 8J6010 3/4-16ORB X #6JIC(M) 90° ADP TO RIGHT SIDE WING LOCK CYLINDER (F & G HOSES) B TO LEFT SIDE WING LOCK CYLINDER (F & G HOSES) 8J5620 3/4" X #6 JIC (F-SW) 8J6000 9/16ORB X #6JIC(M) 90° DETAIL E - SECTION 2 CYLINDER DETAIL G CASTER LOC K C YLIND ER (COMPONENT S REMOVED FOR BET TER VIEW) DETAIL F - CENTER FRAME TEES 8J5500 9/16" X #6 JIC(M) C 8J5500 9/16" X #6
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY Figure 8 - Wiring and Safety Installation 8X0440 8P7310 8K8090A DETAIL A 8K8095A A B 8X0402 8K8095A 8K8075B (2X) (EXT. HARNESS) 8K8090A 8K8030A 8S1120 8S1126 8X0202 3/8" LN 8K8210 8K8070B (MAIN HARNESS) 8A1155 3/8X6-1/16X5" DETAIL B 9/20/2010 2-18 9LR6242.
SECTION 3 – OPERATION LAND ROLLER OPERATION SAFETY 1. READ AND UNDERSTAND Operator’s Manual before using machine. Review at least annually thereafter. 2. VERIFY all safety devices and shields are in place before using machine. 3. KEEP hands, feet, hair and clothing away from moving parts. 4. STOP engine, place all controls in neutral, set parking brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting, maintaining or unplugging. 5.
SECTION 3 – OPERATION INITIAL HOOKUP: 1. Make tractor to hitch connection with locking draw pin and safety chain. 2. Retract jack and rotate into storage position. 3. Plug Lockpin Cylinder hoses into desired tractor outlet, adjust hydraulic flow rate to 35% of maximum. Insure that tips and couplers are CLEAN. 4. Plug Lift Cylinder hoses into desired tractor outlet, adjust hydraulic flow rate to 35% of maximum. 5.
SECTION 3 – OPERATION STEPS REQUIRED TO UNFOLD FROM TRANSPORT TO FIELD POSITION: 1. WARNING: Land Roller must be attached directly to tractor drawbar and not an intermediate towed vehicle or implement. Loss of control could result causing serious injury or death to you or others. Never tow this implement with less than an 30,000 lb. vehicle 2. Ability to safely operate the Summers Land Roller is determined by both tractor horsepower and weight.
SECTION 3 – OPERATION LAND ROLLER FIELD OPERATION: 1. Choose an operating speed which achieves desired results. Operating at over 7 MPH will decrease effectiveness and increase chance of immovable rocks denting roller tube. Denting of roller tube is NOT covered by warranty. 2. Slow down for turns. Because of the weight of the roller turning at high speeds may cause the tractor to “fish tail”. Control will be more easily maintained at slow rates of turns.
SECTION 3 – OPERATION TRANSPORTING LAND ROLLER: 1. If Land Roller is in Field Position, follow “Steps Required to Fold Land Roller from Field to Transport Position”, page 3-4. 2. Ability to safely operate the Summers Superroller is determined by both tractor horsepower and weight. The minimum tractor weight for operating this implement is 30,000 lbs. Minimum tractor engine horsepower is 300. Dual tires or single tires set at maximum width are required for safe operation of Land Roller. 3.
SECTION 3 – OPERATION UNHOOKING LAND ROLLER FROM TRACTOR IN FIELD POSITION: 1. NEVER unhook Land Roller if positioned between Field and Transport Position. 2. Choose a firm level surface. 3. With Land Roller in Field Position; shut off tractor, engage parking brake and relieve hydraulic pressure by cycling remote lever. 4. Block rollers to prevent movement after hitch pin is removed. 5. Check that hitch pin is not bound with sideways or front to back pressure.
SECTION 4 – MAINTENANCE MAINTENANCE SAFETY 1. STOP engine, place all controls in neutral, set parking brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting or maintaining. 2. BE CAREFUL when working around high pressure hydraulic system. 3. ALWAYS make sure that Land Roller is lowered into field position, it is blocked to prevent movement and pressure is relieved from hydraulic circuits before servicing. 4. USE EXTREME CARE when making adjustments. 5.
SECTION 4 – MAINTENANCE PERIODIC MAINTENANCE Caster Wheel Pivot Lock Adjustment The pivot lock cylinders will require periodic adjustment. With the pivot lock cylinder retracted, adjust the lock pin so it is 1/8” inside the lock collar as shown on Page 3-5. Grease all zerks shown in the diagram daily. Check tightness of castle nuts and all component of the caster wheel. 1. Repack wheel bearings and check tightness. 2. Check the tightness of all hardware.
SECTION 5 – PARTS OWNER REGISTER INFORMATION, LOCATED AT THE BEGINNING OF THIS MANUAL, MAY BE NEEDED WHEN ORDERING PARTS (SERIAL NUMBER IS LOCATED BY THE FRONT OF THE HITCH).
8R8010 8X0265 3/4" LN DETAIL A 5-2 8P5080 8P4215 (42" DIA.) 8P4203 (36" DIA.) 8X0111 3/4" X 2-1/2" A AFTER DRUM IS INSTALLED PLACE STANDS AT THE 4 LOCATIONS SHOWN TO STABILIZE FRAME. 2/23/2011 9LR6242.
8X0323 5/8" FW 8X0095 5/8" X 5" 8D9108 1/4 X 2" RP 8X0327 1 1/4" FW DETAIL B 8X0253 NY-LOCK 5/8"-11NC 8P3910 8D9108 1/4 X 2" RP B 8X0327 1 1/4" FW 8D9108 1/4 X 2" RP 8X0304 5/8" LW 8K1620 8P7140 5-3 8P7130 A 8X0327 1 1/4" FW 8D8500 8X0523 ROLL PIN 8X0110 3/4 X 1.25" 8D8490 8K8067 8X0318 3/4" FW 8X0309 1" LW 8X0281 NY-LOCK 1" 8D8522 8D0720 NOTE: DRUM OMITTED FROM THIS VIEW. DETAIL A 8X0140 1 X 7" 3/25/2009 9LR6242.
HITCH AND DRUM OMITTED FOR CLEARER VIEW 8D0340 3/4 X 4 X 7-3/4" 8X0044 7/16" X 3-1/2" 5-4 8K7042 8X0306 3/4" LW 8X0234 7/16" LNUT 8T3640 8D9108 1/4 X 2" RP 8X0265 3/4" LN A 8X0242 NY-LOCK 1/2" N 8X0327 1 1/4" FW 8D9108 1/4 X 2" RP 8X0327 1 1/4" FW 8K9106 8P0510 8K1105S DETAIL A 8D9108 1/4 X 2" RP 8D9108 1/4 X 2" RP 8X0072 1/2" X 3-3/4" 8P7180 8X0327 1 1/4" FW 8X0327 1 1/4" FW 3/25/2009 8K9106 9LR6242.
SECTION 5 – PARTS 8P7100L - 84' LEFT 8P7100R - 84' RIGHT 8P7102L - 62' LEFT (SHOWN) 8P7102R - 62' RIGHT 8X0095 5/8" X 5" 8X0253 NY-LOCK 5/8"-11NC 8K1660 8X0304 5/8" LW 8X0323 5/8" FW 8D9108 1/4 X 2" RP 8X0304 5/8" LW 8X0323 5/8" FW 8X0095 5/8" X 5" 8K9106 DETAIL B 8X0253 NY-LOCK 5/8"-11NC 8X0327 1 1/4" FW 8X0234 7/16" LNUT 8T3640 8T4100 8C1805 8X0327 1 1/4" FW B 8P6100 8P6100 8X0306 3/4" LW 8R6040 A C 8X0265 3/4" LN 8X0044 7/16" X 3-1/2" 8K7042 8P4215 - 62' (SHOWN) 8P4217 - 84' DETAIL
SECTION 5 – PARTS 8X0327 1 1/4" FW 8D9108 1/4 X 2" RP 8D9108 1/4 X 2" RP DETAIL A A 8K9106 8X0095 5/8" X 5" 8X0323 5/8" FW 8P3910 8X0327 1 1/4" FW 8X0323 5/8" FW 8X0304 5/8" LW 8P7150L 8X0095 5/8" X 5" 8X0323 5/8" FW 8X0095 8X0304 5/8" X 5" 5/8" LW 8X0253 NY-LOCK 5/8"-11NC 8X0304 5/8" LW 8P0510 8P3910 8X0253 NY-LOCK 5/8"-11NC 8P7112L - 62' LEFT (SHOWN) 8P7112R - 62' RIGHT 8P7110L - 84' LEFT 8P7110R - 84' RIGHT 8P3910 8P4212 B 8X0265 3/4" LN 8R8010 8X0253 NY-LOCK 5/8"-11NC 8X0306 3/4" LW 8
8X0368 1-1/2" FW 8X0114 3/4 x 3" 5-7 8X0306 3/4" LW 8P7200 8P7250 8K9102 8X0260 3/4" N 8X0261 3/4" LN 8X0292 2" SLTD N 8X0320 3/8" FW 8D9108 1/4 X 2" RP 8X0202 3/8" LN 7P8530 8P7190B 8K1723 8D9108 1/4 X 2" RP 8P7160L 8K5200 7L2150 8L0320 8P0302 8X0306 3/4" LW 8X0122 8X0260 3/4" N 8K7042 8L0252 8K1105S 8X0072 1/2" X 3-3/4" 8X0284 1 1/4" N 8X0242 NY-LOCK 1/2" N 8X0311 1 1/4" LW 12/9/2009 9LR6242.
HUB AND AXLE COMPONENTS Assembly Notes: A. Before towing machine, pack wheel bearings and fill 1/2 of hub cavity with high quality bearing grease. B. Tighten axle nut to 45 ft.-lbs, loosen nut until first slot is aligned with hole in axle, install cotter pin and bend to retain. Legend: SMC Part Number INDUSTRY Part Number or Size H211 1. SEAL 2. INNER BEARING 3. INNER RACE 8G8220 8G8217 8G8230 4. OUTER 5. HUB ASSY RACE 8G8230 8G8211 6. WHEEL STUD 7.
SECTION 5 – PARTS SECTION 5 – PARTS TO REAR CASTER LOCK CYLINDERS (H HOSES) E 8J6010 (4X) FROM TRACTOR (432" HOSES) 8J6010 3/4-16ORB X #6JIC(M) 90° ADP TO RIGHT SIDE WING LOCK CYLINDER (F & G HOSES) B TO LEFT SIDE WING LOCK CYLINDER (F & G HOSES) 8J5620 3/4" X #6 JIC (F-SW) 8J6000 9/16ORB X #6JIC(M) 90° DETAIL E - SECTION 2 CYLINDER DETAIL G CASTER LOC K C YLIND ER (COMPONENT S REMOVED FOR BET TER VIEW) DETAIL F - CENTER FRAME TEES 8J5500 9/16" X #6 JIC(M) C 8J5500 9/16" X #6 JIC(M) 62' - 25
SECTION 5 – PARTS 8X0440 8P7310 8K8090A DETAIL A 8K8095A A B 8X0402 8K8095A 8K8075B (2X) (EXT. HARNESS) 8K8090A 8K8030A 8S1120 8S1126 8X0202 3/8" LN 8K8210 8K8070B (MAIN HARNESS) 8A1155 3/8X6-1/16X5" DETAIL B 9/20/2010 5-10 9LR6242.
SUMMERS MFG. CO., INC. 3/21/12 INSTALLATION AND OPERATION INSTRUCTIONS FOR 8K1800 ACRE METER FOR SUPERROLLER 1. If Roller Shaft is not tapped, weld ½”-20 UNF nut at center of left pivot shaft of middle roller. Position external taper of nut toward shaft. Insure that threads are not damaged by weld heat or spatter. Allow weld to cool. 2. Attach Acre Meter with ½” lock washer. Tighten to 260-390 in-lbs. * For accurate logging of acres, it is important that meter is mounted concentrically on roller shaft.
Stock Code Description 8A1155 U-BOLT 3/8 X 6-1/16 X 5” SQ 8A4048 NYLON TIE .18 X 11” 8A4050 NYLON TIE .30 X 8-7/8” 8A4052 NYLON TIE .30 X 15-1/4” 8C0270 SPLITSTEELBUSH1.375ODX1”ID-1” 8C0432 HYD CYLINDER 4” X 32” 8C1760 U-BOLT 3/4 X 8 X 6” SQ 8C1780 U-BOLT 7/8 X 8 X 10” SQ 8D0330 U-BOLT 5/8 X 6-1/16 X 5-5/8”SQ 8D0340 U-BOLT 3/4 X 4 X 7-3/4” SQ 8D0350 U-BOLT 3/4 X 4 X 10” SQ 8D0720 HITCH PIECE CAST CAT.3CTD PNTD 8D0722 PERFECT HTCH BACKSTOP W/HDWE 8D0724 CLEVIS OPT.HITCH CAT.
Stock Code Description 8N4198 1/2X 198”HYD HOSE#10FJX3000PSI 8N4216 1/2X 216”HYD HOSE#10FJX3000PSI 8N4228 1/2X 228”HYD HOSE#10FJX3000PSI 8N4546 1/2X 546”HYD HOSE#10FJX3000PSI 8N4624 1/2X 624”HYD HOSE#10FJX3000PSI 8P0302 HYD. CYL 3”DIAX1.75” 3500 P1.25RD 8P3010 PLUG 2-1/2” NPT SQUARE HD STL 8P3500 TUBE 2-1/4ODX 1.268ID- 2-1/4” 8P3900 PIN 2 X 11-1/8” HARDENED 8P3910 PIN 2 X 13-1/2” HARDENED 8P4215 ROLLER 42”DIAMETER 15’ 058P5070 ANGL WNG LCK 1/2X3X3.5- 10.25” 8P5080 ANGLE BRNG 3/8X2.5X2.
Stock Code Description 8X0107 BOLT 3/4-10NC X 2” GR5 ZDI 8X0110 BOLT 3/4-10NC X 1-1/4” GR5 ZDI 8X0111 BOLT 3/4-10NC X 2-1/2” GR5 ZDI 8X0112 BOLT 3/4-10NC X 2-1/4” GR5 ZDI 8X0113 BOLT 3/4-10NC X 5” GR5 ZDI 8X0114 BOLT 3/4-10NC X 3” GR5 ZDI 8X0115 BOLT 3/4-10NC X 3-1/2” GR5 ZDI 8X0115A BOLT 3/4NCX 3.
History of Summers Manufacturing Co., Inc. 1965 – Summers Manufacturing is founded by Harley Summers, who purchases patent rights for Goebel truck and pickup hoists from the Goebel Brothers of Lehr, ND. These hoists, produced in Harley Summers’ blacksmith shop the first year, were distributed nationwide by a Cincinnati, Ohio, dealer. With increasing sales, the company soon outgrows the small shop. Summers wins the Herman harrow contract, beginning the company’s Herman culti-harrow line.
Model 700 Rock Picker Superrollers Superchisel Coulter-Chisel Disk-Chisel Hydraulic Fold Coil Packer & Hydraulic Fold Rolling Chopper Mounted Harrows Rolling Choppers Superharrow Plus & Superharrow 2650 Diamond Disk & 2510 DT Supercoulter Plus © Copyright 2013 Summers Manufacturing Co., Inc. All Rights Reserved Rolling Baskets Ultra & Ultimate NT Supersprayer 11-1-12 To find a dealer near you check out our website - www.summersmfg.
