FROST-FREE REFRIGERATOR and FREEZER MODEL NOS. Refrigerator: Freezer: ACR45L ACF33L INSTRUCTION MANUAL BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Model and Serial Nos. (on lower left corner of inside cabinet) here: Model No.: _______________________ Serial No.: _______________________ Felix Storch, Inc. ISO 9001:2015 registered 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5 Installation Instructions 6-8 Before Using Your Appliance 6 Installation of Your Appliance 6 Electrical Connection 6-7 Extension Cord 7 Reversing the Door Swing of Your Appliance 7 Installing the Stainless Steel Handle 8 Operating Your Appliance 8-12 Control Panel for ACR45L 8-9 Control Panel for ACF33L 9-10 Temperature Memory Function 10 Defrosting 10 Using the Freezer ACF33L 10 Door Alarm 11
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the word DANGER or WARNING.
In the event of any damage: - Avoid open flames and anything that creates a spark, - Disconnect from the power supply, - Air the room in which the appliance is located for several minutes, and - Contact the Service Department for advice. The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up.
LOCATION OF PARTS MODEL ACR45L – FROST-FREE REFRIGERATOR MODEL ACF33L – FROST-FREE FREEZER 5
INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior and interior packing. Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth. Install the handle on the door, if it is not already attached. (See page 8.
appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.
INSTALLING THE HANDLE This appliance includes a handle that is not required to operate the unit. To install the handle, follow the instructions below: 1. Use a screwdriver to remove the screws on the side of door where the handle is to be installed. 2. Align the handle with the screws removed in step # 1. Tighten the screws using a Phillips head screwdriver until the handle is both flush and secured tightly against the door side. (DO NOT over-tighten as this will cause damage to the door surface.
Setting the Temperature Control You can set the temperature by pressing the UP and DOWN symbols. When you press either of the two buttons for the first time, the LED readout will show the original temperature set previously. (The temperature preset at the factory is 39°F or 4°C.) The temperature you are setting will increase by one degree each time you press the UP symbol, and will decrease by one degree each time you press the DOWN symbol. The range of set temperature settings is from 36°F to 43°F.
from Fahrenheit to Celsius or from Celsius to Fahrenheit, press and hold the SUPERFREEZE key for 5 seconds. Setting the Temperature Control You can set the temperature by pressing the UP and DOWN keys. When you press either of the two keys for the first time, the LED readout will show the original temperature set previously. (The temperature preset at the factory is -4°F, or -20°C.
DOOR ALARM If the door has been left open for more than 60 seconds, the alarm will sound. Pressing the POWER key once or closing the door can switch off the audible alarm. DOOR LOCK Your unit is provided with a lock and key combination. The keys are located inside the plastic bag that contains the Instruction Manual. Insert the key into the lock and turn it counter-clockwise to unlock the door. To lock the door, do the reverse operation, making sure the metal pin is engaged completely.
Function of Controls MODE/RESET Key: Press ONCE to reset Max/Min temperature record. When the unit is sounding an alarm, press ONCE to turn off the beeping sound. HI/LO Key: Press ONCE to display high alarm setting. Press TWICE to display low alarm setting. Press THREE TIMES to display current temperature reading. ºF/ºC Key: Press this button to change the temperature display scale from Fahrenheit (ºF) to Celsius (ºC).
CARE AND MAINTENANCE CLEANING YOUR APPLIANCE Turn off the power, unplug the appliance, and remove all items, including shelves. Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of baking soda to a quart of water). Wash the shelves with a mild detergent solution. Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts. Wash the outside cabinet with warm water and mild liquid detergent.
HOW TO REMOVE THE THERMOMETER / ALARM If you need to disconnect the thermometer / alarm, please follow these steps: 1. Gently pull out the Thermometer / Alarm (1) and then disconnect it from the temperature sensor cable. (Fig. 1) 2. Unscrew the three screws (2) and (7) to remove the shelf cover (3) and the glass bottle holder (6). Be careful to hold the glass bottle holder (6) and temperature sensor glass bottle (5) firmly after removing the screws. (Fig. 3) 3.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. PROBLEM Appliance does not operate. POSSIBLE CAUSE Appliance is not connected to a power supply. The appliance is turned off. Tripped circuit breaker or a blown fuse. The temperature is not set correctly. The ambient temperature could require a lower temperature setting. The door was opened too often.
“E1”. “E2”, “E3”, “E4”, “E5” or “E7”. The alarm sounds and the temperature display flashes. The icon “--” is lit and flashing in the temperature display. for 3-zone models. “E1” or “E2” indicates that the air temperature sensor has failed. “E3” or “E4”indicates that the defrost sensor in the evaporator has failed. “E5” indicates a defrost heater failure. “E7” indicates a door switch failure.
NOTES 17
NOTES 18
NOTES 19
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
