WINE CELLAR ModelNos.:SWC007/ALWC15/SWC1535B/SWC1102/SWC1875B/ SWC1926/SWC1966 Instruction Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Serial No. (on lower left corner of inside cabinet) here: ___________________________________________ Felix Storch, Inc. An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5-8 Installation Instructions 8-13 Before Using Your Appliance 8 Installation of Your Appliance 8-9 Built-in Cabinet Instructions 9 Electrical Connection 9-10 Extension Cord 10 Reversing the Door Swing of Your Appliance Installing the Stainless Steel Handle 10-12 13 Operating Your Appliance 13-17 Recommended Temperature Settings 13 Control Panel for SWC007 13 Control Panel for ALWC15/SWC1535B/SWC1102/SW
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the wordsDANGER or WARNING.
- Avoid open flames and anythingthat creates a spark, - Disconnect from the electrical power line, - Air the room in which the appliance islocated for several minutes, and - Contact the Service Department foradvice. The more coolant there is in anappliance, the larger the room it shouldbe installed in. In the event of aleakage, if the appliance is in a smallroom, there is the danger ofcombustible gases building up.For every ounce of coolant at least 325cubic feet ofroom space is required.
LOCATIONOF PARTS MODEL SWC007 Door Digital Control Panel Handle Ventilation Grille Adjustable Legs Cabinet MODEL ALWC15 Digital Control Panel Door Shelves(5) Handle Security Lock Ventilation Grille Adjustable Legs Cabinet 5
MODEL SWC1535B Digital Control Panel Door Shelves(6) Handle Security Lock Ventilation Grille Adjustable Legs Cabinet MODEL SWC1875B Digital Control Panel Upper Door Handle Upper Zone Security Lock Lower Door Lower Zone Shelves (14) Ventilation Grille Adjustable Legs Cabinet 6
MODEL SWC1102 Digital Control Panel Handle Shelves (12) Door Security Lock Ventilation Grille Adjustable Legs Cabinet MODEL SWC1926 Digital Control Panel Door Handle Shelves (15) Security Lock Ventilation Grille Adjustable Legs 7
MODEL SWC1966 Door Digital Control Panel Handle Shelves (14) Security Lock Ventilation Grille Adjustable Legs Cabinet INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior and interior packing. Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth.
the top are suggested, which allows the proper air circulation to cool the compressor and condenserfor energy saving. Even for built-in installation, it is a must to keep at least 1/8” (3mm) of space on each side, 5/8” (16mm) at the back and 1/16” (1.6mm) at the top to ensure proper service access and ventilation. And the air vent at the front of the appliance must never be covered or blocked in any way.
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord. EXTENSION CORD Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this appliance.
- Model SWC1875B 7 8 3 2 1 4 4 5 6 10 1. Remove the plastic cover (1) then remove thebottom hinge(3) by unscrewing thefour screws (2).Be careful to hold the lower glass door (4)firmly after removing the screws. And then gently pull down to remove the lower glass door from the middle hinge and place it on a padded surface to avoid the risk of damage. (Fig. 1) 2. Unscrew and transfer the door adapter (5) and (8) to the designated opposite position of lower glass door.
10. Recheck and adjust the lower door alignment by loosening the screws (6) &(7) and moving the door adapter (5) & (8). Tighten the screws (6) &(7)after the door is levelled. (Fig. 5) 11. Transfer the handles and plugs to the opposite positions.(See page 13. Handle Installation) - Model SWC1102/SWC1926/SWC1966 6 4 3 2 1 5 7 3 4 9 1 1. Remove the plastic cover (1) the remove the bottom hinge (3)by unscrewing thefour lock screws (2).
INSTALLING THE STAINLESS STEEL HANDLE This appliance includes a stainless steel handle that is not required to operate the unit. To install the handle, follow the instructions below: 1. Remove the door gasket (2) on the side you wish to install the handle - you can see two designated holes for handle installation. 2. Install the handle (4) tightly as shown above with two screws (1) and flat washers (3) provided. 3. Replace the door gasket.
NOTE: Pressing thePOWER key once can switch off the audible alarm when the alarm is on. LIGHT Turn the interior light on and off with this switch. UP Used to increase (warm) the set temperature by 1°C/1ºF. DOWN Used to decrease (cool) the set temperature by 1°C/1ºF. Indicator Light The indicator light is the decimal pointlocated at the right lower corner of the display. The indicator light will be on when a multi-key function is selected.
UP Used to increase (warm) the set temperature by 1°C/1ºF. DOWN Used to decrease (cool) the set temperature by 1°C/1ºF. Indicator Light The indicator light is the decimal pointlocated at the right lower corner of the display. The indicator light will be on when a multi-key function is selected. To perform a multi-key function, press and hold the first key, then press the second key for at least 5 seconds and then release both keys.
INTERIOR LIGHT The interior light makes it easy to view your wine labelsand enhances the display of your collection. TheLIGHTswitch allows you to toggle between 2 modes of operation forthe internal lights: functional (default) mode and showcasemode. If you are in functional (default) mode(also named as energy saving mode), the lightswill turn on only when the door is open. If you are in showcasemode, the lights will be on whether or not the door is open.
WINE SHELVES To prevent damaging the door gasket, make sure to have the door all the way open when pulling the shelves out of the rail compartment. For easy access to the storedbottles, you canpull the shelf approximately halfwayout of the rail compartment.However this unit was designed with a plastic post on each side of the shelf track to prevent bottles from falling. When removing the wooden shelf from the inner rails, make sure to remove all bottles first.
CARE AND MAINTENANCE CLEANING YOUR WINE CELLAR Turn off the power, unplug the appliance, and remove all items, including shelves. Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of baking soda to a quart of water). Wash the shelves with a mild detergent solution. Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting Guide PROBLEM Appliance does not operate. POSSIBLE CAUSE Appliance is not connected to a power supply. The appliance is turned off. Tripped circuit breaker or a blown fuse. The temperature is not set correctly. The ambient temperature could require a lower temperature setting.
The appliance is not properly level. The door will not close properly. Display “E0”, “E1”. “E2”, “E3”, “E4”, “E5” or “E7”. The alarm sounds and the temperature display flashes. The icon “--” is lit up and flashing in the temperature display. The door was reversed and not properly installed. The gasket is dirty. The shelves are out of position. “E0”indicates a communication error for 3-zone models. “E1” or “E2” indicates that the air temperature sensor has failed.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.