BEVERAGE MERCHANDISERS Model Nos.: SCR615TD / LCR625 / FF616TD User Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Serial No. (on lower left corner of inside cabinet) here: ____________________________________________ Felix Storch, Inc. An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5 Installation Instructions 6-8 Before Using your Appliance 6 Installing your Appliance 6 Electrical Connection 7 Extension Cord 7 Reversing the Door Swing of your Appliance 8 Installing the Stainless Steel Handle 8 Operating your Appliance 9-11 Control Panel 9-10 Sabbath Mode 10 Temperature Memory Function 10 Temperature Alarm/Door Alarm 10 Door Lock 10 Defrosting 11 Bottle Storage and Accessor
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words "DANGER" or "WARNING".
parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes. In the event of any damage: - Avoid open flames and anything that creates a spark, - Disconnect from the electrical power line, - Air the room in which the appliance is located for several minutes and - Contact the Service Department for advice. The more coolant there is in an appliance, the larger the room it should be installed in.
LOCATION OF PARTS 5
INSTALLATION INSTRUCTIONS Before Using your Appliance Remove the exterior and interior packing. CAUTION: After unpacking you MUST allow your appliance to stand upright for at least 2 hours to allow the lubricant and refrigerant to drain back into the compressor and stabilize. Failure to do so may adversely affect performance and the lifetime of the unit. Clean the interior surface with lukewarm water using a soft cloth. Install the handle on the door. (See page 8.
Electrical Connection WARNING Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by a qualified electrician or an authorized service center. This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of electrical shock.
Reversing the Lower Door Swing of your Appliance This unit has the capability of the door opening from either the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow the reversal instructions shown below. NOTE: All parts removed must be saved to allow the door swing to be reversed. 1. Remove the bottom hinge 2 by unscrewing the four lock screws 1.
OPERATING YOUR APPLIANCE It is recommended that you install the appliance in a place where the ambient temperature is between 72º and 78ºF (23º-26ºC). If the ambient temperature is above or below the recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extremely cold or hot conditions may cause interior temperatures to fluctuate. The range of 36º-43ºF (2º-6ºC) may not be reached.
The temperature you are setting will increase by one degree each time you press the UP symbol, and will decrease by one degree each time you press the DOWN symbol. The range of the temperature control is from 36°F/2°C to 43°F/6°C. To view the set temperature at any time, press the UP or DOWN symbol. The set temperature will flash in the display window for 5 seconds. After 5 seconds, the temperature inside the unit will reappear in the display window.
Defrosting The unit defrosts automatically during normal operating conditions. The evaporator behind the rear wall of the unit defrosts automatically. The condensate collects in the drainage channel behind the rear wall of the unit, and flows through the drainage hole into the drip tray by the compressor where it evaporates. However, frost may accumulate on the evaporator if the unit is repeatedly opened in a high heat or high humidity location.
CARE AND MAINTENANCE Cleaning your Beverage Merchandiser Turn off the power, unplug the appliance, and remove all items, including shelves. Wash the inside and outside surfaces as well as the shelves with warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft cloth. Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts. Do not use steel wool or a steel brush on the stainless steel.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting Guide PROBLEM The appliance does not operate. The appliance is not cold enough. POSSIBLE CAUSE Appliance is not connected to a power source. The appliance is turned off. Tripped circuit breaker or a blown fuse. REMEDY Connect the appliance. The temperature is not set correctly.
may cause popping and crackling noises. The door will not close properly. The appliance is not properly level. Level the appliance with the adjustable feet. The appliance is not properly level. Level the appliance with the adjustable feet. Check the door hinge and reassemble correctly. Clean the door gasket. Check the shelves and refit correctly. The door was reversed and not properly installed. The gasket is dirty. The shelves are out of position. Call for service. Display “E0”, “E1”.
NOTES 15
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
