FROST-FREE DRAWER REFRIGERATORS and DRAWER FREEZERS Model Nos. FF642D / SPR627OS2D SCFF532D / SPFF51OS2D INSTRUCTION MANUAL BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Serial Number (on lower left corner of inside cabinet) here: Serial No.: _______________________ Felix Storch, Inc. An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5 Installation Instructions 6-8 Before Using Your Appliance 6 Installation of Your Appliance 6 Electrical Connection 6-7 Extension Cord 7 Anti-Tip Bracket Installation 7 Installing the Stainless Steel Handles 8 Full Overlay Panel Installation Instructions 8 Operating Your Appliance 9-12 Control Panel for FF642D/SPR627OS2D 9-10 Control Panel for SCFF532D/SPFF51OS2D 10-11 Sabbath Mode 11 Temperature M
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the word DANGER or WARNING.
In the event of any damage: – Avoid open flames and anything that creates a spark, – Disconnect from the power source, – Air the room in which the appliance is located for several minutes, and – Contact the Service Department for advice. • The more coolant there is in an appliance, the larger the room in which it should be installed. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up.
LOCATION OF PARTS NOTE: Refrigerator model SPR627OS2D and freezer model SPFF51OS2D are designed for outdoor as well as indoor use. They are equipped with a reinforced exterior and a power cord made to stand up to the elements. Refrigerator model FF642D and freezer model SCFF532D are for indoor use only.
INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE • Remove the exterior and interior packing. • Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. • Clean the interior surface with lukewarm water using a soft cloth. • Install the handles on the drawers, if they are not already attached. (See page 8.
The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged.
INSTALLING THE STAINLESS STEEL HANDLES This appliance includes two stainless steel handles that are not required to operate the unit. To install the handles, follow the instructions below: 1. Remove the door gasket. 2. Install the handle with the screws provided. (DO NOT over-tighten as this will cause damage to the stainless steel door surface.) 3. Replace the door gasket. FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS These models are designed for field-installed overlay panels.
OPERATING YOUR APPLIANCE It is recommended you install the appliance in a place where the ambient temperature is between 44º and 95ºF (7º to 35ºC). If the ambient temperature is above or below the recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extremely cold or hot conditions may cause interior temperatures to fluctuate. The expected operating temperature range may not be reached.
Interior Light • The interior light makes it easy to view your items. Pressing the LIGHT symbol toggles between 2 modes of operation for the internal lights: functional (default) mode and showcase mode. If you are in functional (default) mode, the lights will turn on only when a drawer is open. If you are in showcase mode, the lights will be on whether or not the drawer is open.
flash in the display window for 5 seconds. After 5 seconds, the temperature inside the unit will reappear in the display window. Interior Light The unit is equipped with an interior LED light which will be turned ON when a drawer is open. NOTE: • If the unit is unplugged or power is lost or turned off, you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the unit will not start.
TEMPERATURE ALARM / DOOR ALARM • An audible alarm sounds if the storage temperature is not cold enough. The temperature display flashes at the same time. • The cause of the temperature being too high may be: – Warm fresh food was placed inside – Too much warm ambient air flowed in when rearranging and removing food – Power failure for some time – The appliance is faulty.
CARE AND MAINTENANCE CLEANING YOUR APPLIANCE • Turn off the power, unplug the appliance, and remove all items, including racks and dividers. • Wash the inside surfaces with a solution of warm water and baking soda (about 2 tablespoons of baking soda to a quart of water). • Wash the racks and dividers with a mild detergent solution. • Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting Guide PROBLEM Appliance does not operate. Appliance is not cold enough. Appliance turns itself on and off frequently. POSSIBLE CAUSE • Appliance is not connected to a power supply. • The appliance is turned off. • Tripped circuit breaker or blown fuse • The temperature is not set correctly.
Display “E0”, “E1”. “E2”, “E3”, “E4”, “E5” or “E7”. The alarm sounds and the temperature display flashes. The icon “--” is lit and flashing in the temperature display. • “E0” indicates a communication error for 3 zone models. • “E1” or “E2” indicates that the air temperature sensor has failed. • “E3” or “E4”indicates that the defrost sensor in the evaporator has failed. • “E5” indicates defrost heater failure. • “E7” indicates door switch failure.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.