Owner's Manual
Table Of Contents
- IMPORTANT SAFEGUARDS
- /Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. SUMMIT® APPLIANCE strongly recommends that you have a professional install your new machine. The warranty may be aff...
- SAVE THESE INSTRUCTIONS
- Electrical Connection
- Extension Cord
- Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this ice maker.
- TECHNICAL INFORMATION
- Excessive Weight Hazard
- Electrical Shock Hazard
- You must connect the drain line before using the ice maker. Follow the steps below.
- Connecting the drain line:
- Mobile installation:
- Enclosed Installation:
- Operating Method
- Set the ON/OFF button to the ON position. The machine will automatically go to the ice making stage.
- There are two distinct cycles: ice freeze and harvest.
- Preparing the Ice Maker for Long Storage
- Exterior cleaning
- MAJOR FUNCTIONS
- IMPORTANT SAFEGUARDS
- /Avant la machine à glaçons est utilisée, elle doit être correctement positionnée et installée comme décrit dans ce manuel, donc lire attentivement le manuel. SUMMIT® APPLIANCE recommande fortement que vous avez un professionnel installer votre nouvel...
- CONSERVEZ CES INSTRUCTIONS
- Connexion électrique
- Rallonge
- En raison des risques potentiels pour la sécurité dans certaines conditions, il est fortement recommandé de ne pas utiliser une rallonge avec ce fabricant de glace.
- INFORMATIONS TECHNIQUES
- Vous devez connecter la ligne de vidange avant d'utiliser la machine à glaçons. Suivez les étapes ci-dessous.
- Installation mobile :
- Installation close :
- Méthode de fonctionnement
- Risque de choc électrique
- Réglez le bouton ON / OFF sur la position ON. La machine se met automatiquement à l'étape de fabrication de glace.
- Il y a deux cycles distincts: la congélation de la glace et la récolte.
23
Water distribution tube cleaning
When you find the ice cubes are incompletely formed or the output is low, the water
distribution tube may be blocked. Turn off the power button, gently take out the water
distribution tube, locate the holes in the distribution tube and use a pointed object such as
a toothpick to dredge the holes. Then put the water distribution tube back to its original
position. If the tube is badly blocked, clean it as follows:
1. Shut off the water supply
2. Disconnect the water hose from the distribution tube.
3. Gently take out the distribution tube.
4. With a brush, clean the tube with a dilute solution of warm water and a mild detergent
such as dishwashing liquid. After removing the dirt and lint from the surface, rinse the
tube with clean water.
5. Replace the distribution tube.
6. Reconnect the water supply.
Ice-making system cleaning
Minerals that are removed from the water during the freezing cycle will eventually form a
hard, scaly deposit in the water system. Cleaning the system regularly helps remove the
mineral scale buildup. How often to clean the system depends upon how hard your water
is or how effective your filtration may be. With hard water of 15 to 20 grains/gal. (4 to 5
grains/ liter), you may need to clean the system as often as once every 6 months.
1. Make sure that all the ice is off the evaporator. If ice is being formed, wait until the
cycle is completed, then press the machine’s ON/OFF switch on the control panel.
2. Remove all ice from the storage bin.
3. Keep the ice maker connected to the water supply. Pour 8 oz. of Nickel-Safe Ice
Maker Cleaner Solution into the water trough. Then press the ON/OFF switch and the
CLEAN button, initiating the wash cycle. The machine will run in the Automatic
Clean Mode.
4. Allow 30 minutes for proper cleaning. After cleaning, press the ON/OFF switch again.
Use a drain hose on the front of the water trough to drain off the waste water to a
convenient container.
NOTE: Don’t drain off the waste water to the inside of the cabinet.
5. Repeat steps 3 and 4 (without Ice Maker Cleaning Solution) three times to rinse the ice
making system thoroughly.
• NOTE: Ice Maker Cleaner Solution in the water bin during the rinse is not
needed.