INDOOR/OUTDOOR ICE MAKER Models BIM68OSGDR BIM68OSPUMP User’s Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Write Model and Serial Numbers here: FELIX STORCH, INC. Summit Appliance Division An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, New York 10474 Model No.: _____________________ Ser. No.
Table of Contents Ice Maker Safety ............................................................................................... 2 Important Safeguards ................................................................................. 3 - 5 Electrical connection ................................................................................ 4 - 5 Extension cord .............................................................................................. 5 Unpacking, etc. .................................
ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can injure or kill you and others. Safety messages will follow the Safety Alert Symbol and either the words "DANGER", "WARNING" OR "CAUTION".
IMPORTANT SAFEGUARDS Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. SUMMIT® APPLIANCE strongly recommends that you have a professional install your new machine. The warranty may be affected or voided by an incorrect installation.
It is important for the ice maker to be leveled in order to work properly. Otherwise water may not flow properly through the evaporator (ice mold). The ice production will be less than normal. You may need to make several adjustments to level it. All installations must be in accordance with local plumbing code requirements. Make certain that hoses are not pinched, kinked or damaged during installation. Check for leaks after water line is connected.
label on the appliance. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. Never unplug your ice maker by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
The mineral content of the ice produced by the ice maker is reduced compared to the content in the water before conversion into ice. Water containing a low level of impurities is rapidly frozen. The reason for this is that the impurities elevate the temperature of the water. Through such action, most of the impurities condensed in the water-tank of the ice maker form a hard precipitation called scale.
Location of Parts FRONT Door handle Top cover Water tank Door Operation switch Front panel Bottom grill BACK Back cover Water supply socket (inlet) Drain hose Power cord Notes: Model BIM68OSGDR is a gravity-drain ice maker. Model BIM68OSPUMP includes an internal pump. Each has a heavy-duty power cord and stainless steel door and cabinet, and is suitable for either indoor or outdoor use.
Installation Space requirements for installation When moving the ice maker, check whether the prepared opening dimensions, electric power, and piping position are correct. Refer to the installation specifications and drawings shown on pages 10 and 11. Figures 4, 5, 6 and 7 show the dimensions of the ice makers. Model BIM68OSGDR is a gravity drain pipe model that requires a drain pipe to run from the exhaust hole at the back of the product to an appropriate drain.
Requirements for plumbing Plan the arrangement of the water supply pipes. Connect a 1/4" diameter copper cable with the tap water pipe. Install a shutoff valve between the tap water pipe and the product so that the user can operate the valve. Do not install the shutoff valve at the back of the product. Do not use a self-piercing valve. If the tap water has a high level of minerals, a pipeline filter will be required. The pressure of the tap water should be maintained at a level between 20psi (1.
Gravity Drain Pipe Model (BIM68OSGDR) Before connecting the drain tube and the water supply pipe with the ice maker, pipes should be arranged as follows. The horizontal distance of the drain tube should be 1/4" for every 12" (305 mm) distance. An air gap is required between the drainage tube of the ice maker and the drain pipe or sewage container. A stand pipe fitted with a trap at the lower part may be used as a drain pipe or sewage container.
Drain Pump Model (BIM68OSPUMP) 1) Arrange the ice maker at the front of the installation opening. 2) Adjust the leveling legs to the appropriate height. 3) Install the inlet pipe (copper pipe with a diameter of 1/4”) on the wall and connect the water supply valve. 4) Connect the drain pipe from the wall to the ice maker. 5) Important Information: An air gap may be required between the drain tube of the ice maker and the container of the drain pipe under the provision of local laws and regulations.
What to check prior to installation Follow this process! The water supply valve may have different shapes depending on the installation condition. ● The filter may be located close to the water source or back of the product depending on the situation. ● Water inlet:Connectthewatertapadaptortothewa Avoid uneven surfaces or places with too much moisture, tersupply too much dust, or spattering water. direct sunlight, connectionportnearthewatersupplyvalve.
Changing Door-opening Direction The direction in which the door with fixed hinges opens may be changed. The hinges are attached to the right-hand side of the door when the product is shipped from the factory. However, the ice maker is designed so that the hinges may be installed on either side. If the hinges are moved to the holes on the left-hand side, the door will open to the left.
Installation Checklist Important Information: The installation engineer should check whether any installation part has been omitted and follow the check list below to ensure safe and proper installation. If you have any questions or problems regarding installation, address your queries to the distributor or dealer. You may also seek information on the company’s website. Does the ice maker work properly? If the ice maker does not work, check whether the plug has been inserted properly.
SpecificFeatures Fig. 9: Ice maker Sink-Mounted Ice Maker The gravity drain-type naturally drains water, whereas the drain pump-type drains water to an adjacent sink using a built-in pump. A perfect and unified design system with a depth of 24" (610 mm). A decorative door panel may be installed. The product supplies good-quality, transparent ice. The maximum capacity of the ice container is 26 lbs(12kg). Automatic ice-removal function. Left/Right opening door system.
Operation Initial operation Open the water supply valve connected with the ice maker. ② Insert the plug of the ice maker into the electric outlet. ③ Open the door and turn the switch at the lower end of the product to the “ICE” position.” ④ Discard the first batch of ice. ⑤ Good-quality ice is produced 1-2 hours later. ① Using the ice maker Use of the ice maker is very simple. Simply turn the switch at the lower end of the product to the “ICE” position.
Operation time It takes about 20-35 minutes to produce a batch of 24 ice cubes. The length of one cycle of the ice maker (ice production and ice removal) differs depending upon the cleanness of the ice maker, the surrounding temperature, and the temperature of the water supplied to the ice maker. It takes about 10-12 hours to fill the empty ice container with ice. Ice production The ice production process largely consists of two cycles: ice production and ice removal.
Cleaning Cleaning the nozzle / ice slide / water tank 1. Open the door and remove two front injection bolts on the top cover. 2. Pull the top cover to remove it. 3. Slightly lift the ice slide to remove it. 4. Clean the slide with a soft plastic brush or sponge.
5. Clean the gap of the nozzle frame fixed on the vessel sheet (water tank). 6. Lift the drain projectile inside the vessel sheet (water tank), clean it, and drain the water. • Make sure the drain projectile is assembled back in the correct position after cleaning; otherwise, draining will not stop, with the product rendered unable to make ice cubes. Cleaning the nozzle / ice slide / water tank: - Clean at least once a month after turning off power.
2. Open the front door and remove the filter screens from the bottom of the ice tank and water tank. Water tank Ice tank 3. Rinse the screens with running water, and then assemble them back to the tanks. • Otherwise, the water nozzle will get clogged, or dregs inside the ice tank may damage the product by clogging the draining port. • Insert the bottom filter screen first, followed by the top screen.
Cleaning the condenser 1. Remove two screws on the front panel at the center of the inside. 2. Remove dust from the surface of the condenser with a vacuum cleaner. 3. Reassemble the screws to the panel after cleaning. Cleaning the condenser: Clean at least once a month after turning off power.
Maintenance Maintenance in winter ① Clean the ice-production system. ② Turn off the power. ③ Empty the water container. Remove the pump hose. (The pump hose may be removed after removing the back panel from the ice maker.) ④ Separate the inlet pipe connected with the water supply valve. ⑤ Turn on the power and set the switch at the “WASH” position to open the water supply valve and to remove the water from the inlet pipe inside the ice maker.
Specifications ICE MAKER CATEGORY UNIT BIM68OSGDR / BIM68OSPUMP Maximum Ice-Making Capacity※ kg/day 29 lb/day 63.9 WxDxH (mm) 378 x 624 x 855 (excluding handle, legs, hinge) Dimensions WxDxH (inch) 14.9x22.8x33.
Troubleshooting PROBLEM Ice maker does not operate Ice cubes are too large POSSIBLE CAUSE Ice maker is unplugged Plug ice maker in. Breaker tripped Reset breaker - if it happens again, call an authorized service center. Switch turned to “OFF” Turn switch to “ICE”. The ice tank is full. The ice maker has stopped since the ice detection sensor inside the tank is activated. The ice maker will not resume operation immediately after removing ice -- wait for 15~30 minutes.
Notes 25
Notes 26
Limited Warranty ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
