ELECTRIC COOKTOP / TABLE DE CUISSON ÉLECTRIQUE Owner’s Manual / Mode d’emploi Models / Modèles: CR2B22ST / LCR22B BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. AVANT UTILISATION, VEUILLEZ LIRE ET SUIVRE TOUTES LES RÈGLES DE SÉCURITÉ ET LES INSTRUCTIONS D'UTILISATION. Write Serial No. (on bottom of unit) here: Inscrivez le numéro de série (au bas de l'unité) ici: ______________________________ FELIX STORCH, INC.
TABLE OF CONTENTS Appliance Safety 2 Important Safeguards 2-4 Location of Parts 5 Installation Instructions 6-9 Before Using Your Appliance 6 Installation of Your Appliance 6-7 Electrical Connection 8-9 Operating Your Appliance 10 Operating Your Cooktop 10 Operating Indicators 10 Cookware Selection 10 Care and Maintenance 11 Cleaning Your Appliance 11 Troubleshooting 12 Limited Warranty 13 French version of this manual 14 - 27 1
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words DANGER or WARNING.
FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL This appliance is only intended for residential cooking. The manufacturer cannot be held responsible for damage or injury caused by improper use or for uses other than those for which this appliance is intended. Do not touch hot surfaces. Use handles or knobs. To protect against electrical shock, do not immerse cordor body of unit in water or other liquid. Close supervision is necessary when any appliance is used by or near children.
Use Only Dry Potholders – Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth. Make Sure Reflector Pans or Drip Bowls Are in Place – Absence of these pans or bowls during cooking may subject wiring or components underneath to damage. Protective Liners – Do not use aluminum foil to line surface unit drip bowls or oven bottoms, except as suggested in the manual.
LOCATIONOF PARTS BURNER(1800W/7") BURNER(1200W/51 2") OPERATING INDICATOR RESIDUAL HEAT INDICATOR CONTROL KNOB 5
INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior packing. Check if there is any damage to the unit. Clean the unit. A thorough cleaning with a recommended cooktop cleaner will provide a clean, shiny coating on the cooktop surface. INSTALLATION OF YOUR APPLIANCE Follow these directions to prepare the countertop cutout and install your cooktop: 1. Countertop Preparation NOTE: Please read this section prior to making cutout for cooktop.
the cooktop. Heat transferred from the cooktop bottom pan during operation will overheat an improperly ventilated area. Allow a 2" minimum clearance between the bottom of the metal pan of the cooktop and any combustible surface located below, i.e.: the upper edge of a drawer installed below the cooktop. Failure to provide proper clearances and ventilation may result in a fire hazard. If the cooktop is installed above an oven, keep the cooktop’s power cord from contacting the oven.
ELECTRICAL CONNECTION WARNING Improper connection of the equipment-grounding can result in the risk of electrical shock. If the power cord of the unitis damaged, have it replaced by an authorized service center. The appliance must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA No. 70 (Latest Edition) and local electrical code requirements. Installation should be made by a licensed electrician.
2. 4-Wire Power Cord Installation IMPORTANT: Use the 4-wire cable from power supply where local codes do not permit connecting the frame-ground conductor to the neutral (white) junction box wire. 1. Disconnect power 2. Remove junction box cover if present. 3. Connect the flexible cable conduit (3) from the 1 cooktop to the junction box (4) using a UL listed or CSA approved conduit connector (7). 4. Tighten screws on conduit connector, if present. 5.
OPERATING YOUR APPLIANCE OPERATING YOUR COOKTOP Any burner can be turned on by pushing the control knob down and turning it clockwise or counterclockwise to the desired setting. To adjust the setting, turn the knob without pressing down. The burner is turned off by turning the control knob clockwise or counter-clockwise to "OFF". OPERATING INDICATORS When the burner is turned on, the corresponding operating indicator will light up regardless of the setting.
CARE AND MAINTENANCE CLEANING YOUR APPLIANCE Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface and to components for which the manufacturer cannot accept responsibility. Do not use any sharp, pointed objects which could damage the seal between the ceramic surface, the surrounding frame and the countertop.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling a service technician. Troubleshooting Guide PROBLEM POSSIBLE CAUSE The appliance does not operate. Not connected to power supply. Circuit breaker has tripped or fuse is blown. The heating element cycles on and off frequently. The power setting is too low.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
TABLE DES MATIÈRES Sécurité de l'appareil 15 Mesure de sécurité importantes 15 - 17 Emplacement des pièces 18 Instructions d'installation 19 - 23 Avant d'utiliser votre apparei 19 Installation de votre appareil 19 - 21 Connexion électrique 22 - 23 Utilisation de votre appareil 24 Utiliser votre table de cuisson 24 Indicateurs de fonctionnement 24 Sélection des ustensiles de cuisson 24 Dépannage 25 Soin et entretien 26 Nettoyer votre appareil 26 Garantie limitée 27 14
SÉCURITÉ DE L'APPAREIL Votre sécurité et celle des autres sont très importantes. Nous avons fourni de nombreux messages de sécurité importants dans ce manuel et sur votre appareil. Toujours lire et obéir à tous les messages de sécurité. C'est le symbole d'alerte de sécurité. Le symbole vous avertit des dangers potentiels qui peuvent tuer ou blesser vous et d'autres. Tous les messages de sécurité suivront le symbole d’alerte de sécurité et les mots DANGER ou AVERTISSEMENT.
AVERTISSEMENT SUIVEZ LES AVERTISSEMENTS CI-DESSOUS UNIQUEMENT LORSQU’ILS SONT APPLICABLES À VOTRE MODÈLE Cet appareil est uniquement destiné à la cuisine résidentielle. Le fabricant ne peut être tenu responsable des dommages ou des blessures résultant d'une utilisation incorrecte ou pour des utilisations autres que celles auxquelles cet appareil est destiné. Ne touchez pas les surfaces chaudes. Utilisez des poignées ou des boutons.
Ne touchez pas les éléments chauffants ou les zones proches des éléments chauffants - Les éléments chauffants peuvent être chauds même s'ils sont de couleur sombre. Les zones proches des éléments chauffants peuvent devenir suffisamment chaudes pour causer des brûlures.
EMPLACEMENT DES PIÈCES BR LEUR(1800W/7") BR LEUR(1200W/51 2") INDICATEUR DE FONCTIONNEMENT INDICATEUR DE CHALEUR R SIDUELLE BOUTON DE CONTROLE 18
INSTRUCTIONS D’INSTALLATION AVANT D'UTILISER VOTRE APPAREIL Retirez l'emballage extérieur. Vérifiez si l'appareil est endommagé. Nettoyez l'appareil. Un nettoyage en profondeur avec un nettoyant pour table de cuisson recommandé donnera un revêtement propre et brillant à la surface de la table de cuisson. INSTALLATION DE VOTRE APPAREIL Suivez ces instructions pour préparer la découpe du comptoir et installer votre table de cuisson : 1.
Avant de découper le comptoir, vérifiez le jeu. Vérifiez si la table de cuisson dégage les parois avant et latérales de l’armoire de base. Il est également important de prévoir une ventilation suffisante. Une ventilation adéquate de l'espace sous le comptoir doit être fournie pour assurer le bon fonctionnement de la table de cuisson. La chaleur transférée du plateau inférieur de la table de cuisson pendant le fonctionnement peut surchauffer une zone mal ventilée.
2. Installer la table de cuisson Quatre supports de montage sont fournis avec la table de cuisson électrique. Ces supports sont conçus pour maintenir la table de cuisson fermement en place. La table de cuisson doit être collée au comptoir en utilisant un composé de literie doux qui empêchera les dommages si un retrait ultérieur est nécessaire. Nous recommandons une très petite perle de mastic silicone.
CONNEXION ÉLECTRIQUE AVERTISSEMENT Une mauvaise connexion de la mise à la terre de l'équipement peut entraîner un risque de choc électrique. Si le cordon d'alimentation de l'appareil est endommagé, faites-le remplacer par un centre de service autorisé. L'appareil doit être correctement installé et mis à la terre par un technicien qualifié conformément au code électrique national ANSI / NFPA N ° 70 (dernière édition) et aux exigences du code électrique local.
boîte de jonction à l'aide de l'écrou de fil répertorié UL. 8. Installez le couvercle de la boîte de jonction. 9. Rebranchez le courant. 2. Installation du cordon d'alimentation à 4 fils IMPORTANT: Utilisez le câble à 4 fils de l'alimentation électrique lorsque les codes locaux ne permettent pas de connecter le conducteur de masse du châssis au fil neutre (blanc) de la boîte de jonction. 1. Déconnecter l’alimentation. 2. Retirez le couvercle de la boîte de jonction, le cas échéant. 1 3.
UTILISATION DE VOTRE APPAREIL UTILISER VOTRE TABLE DE CUISSON Vous pouvez allumer n’importe quel brûleur en poussant le bouton de commande vers le bas et en le tournant dans le sens des aiguilles d’une montre ou dans le sens inverse des aiguilles d’une montre pour obtenir le réglage souhaité. Pour ajuster le réglage, tournez le bouton sans appuyer. Pour éteindre le brûleur, tournez le bouton de commande dans le sens des aiguilles d'une montre ou dans le sens inverse pour le désactiver.
DÉPANNAGE Vous pouvez résoudre facilement de nombreux problèmes courants et économiser ainsi le coût d'un appel de service éventuel. Essayez les suggestions ci-dessous pour voir si vous pouvez résoudre le problème avant d'appeler un technicien de maintenance. PROBLÈME CAUSE POSSIBLE L'appareil ne fonctionne pas. Non connecté à l'alimentation. Le disjoncteur s'est déclenché ou le fusible a sauté. L'élément chauffant s'allume et s'éteint fréquemment. Le réglage de puissance est trop bas.
SOIN ET ENTRETIEN NETTOYER VOTRE APPAREIL N'utilisez pas de nettoyeur à vapeur pour nettoyer cet appareil. La vapeur pourrait pénétrer dans les composants électriques et provoquer un court-circuit. La vapeur sous pression pourrait causer des dommages permanents à la surface et aux composants pour lesquels le fabricant ne peut être tenu responsable. Ne pas utiliser d'objets pointus qui pourraient endommager le joint entre la surface en céramique, le cadre environnant et le comptoir.
GARANTIE LIMITÉE UN AN DE GARANTIE LIMITÉE Dans les 48 États américains contigus, pendant un an de la date d’achat, lorsque cet appareil est utilisé et entretenu conformément aux instructions jointes à ou fournies avec le produit, le garant paiera pour les pièces spécifiées en usine et pour la main-d’œuvre pour corriger les défauts de matériaux ou de fabrication. Le service doit être fourni par une compagnie de service désignée.